TC-21FJ30LA Important Safety Notice Special components are used in this television set which are important for safety. These parts are identified on the schematic diagram by the symbol . It is essential that these critical parts are replaced with the manufacturer’s specified replacement parts to prevent X-ray radiation, shock, fire or other hazards.
TC-21FJ30LA ABOUT LEAD FREE SOLDER (PbF) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead. We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn), Silver, (Ag), and Copper, (Cu).
TC-21FJ30LA IC601 - PINOUT Symbol Description P3.1/ADC1 port 3.1 or ADC1 input P3.2/ADC2 port 3.2 or ADC2 input P3.3/ADC3 port 3.3 or ADC3 input VSSC/P digital ground for m-Controller core and periphery P0.5 port 0.5 (8 mA current sinking capability for direct drive of LEDs) P0.6/CVBSTD...
TC-21FJ30LA IC601 - PINOUT Symbol Blue output VDDA analog supply of Teletext decoder and digital supply of TV-processor (3.3 V) OTP Programming Voltage VDDC digital supply to core (3.3 V) OSCGND oscillator ground supply XTALIN crystal oscillator input XTALOUT crystal oscillator output...
TC-21FJ30LA THE DAC CONTROL FOR GP3 CHASSIS FUNCTIONS AND ADJUSTMENTS HOW TO ENTER IN THE SERVICE MODE: 1- Set the “OFF TIMER” to 30 minutes. 2- Press simultaneously “RECALL” key on the remote control and VOL(-) button on the unit.
TC-21FJ30LA ADJUSTMENTS CHK2 MODE - VCJ ADJUSTMENTS CHK2 MODE TABLE On CHK2 mode it is possible to adjust the items of the table shown here. Standard values Note: To select an item, type “4” to move forward and “3” to move back.
TC-21FJ30LA ADJUSTMENTS ITEM / PREPARATION PROCEDURE ADJUSTMENT: 1- RF AGC ADJUSTMENT 1. Select “RF AGC” on “CHK2” service mode. 1. Supply a color bar pattern and adjust the RF input signal of 69 dB µV (75Ω opened channel 07 RF freq.: 175.25 2.
TC-21FJ30LA ADJUSTMENTS ITEM / PREPARATION PROCEDURE 5- PAL COLOR OUTPUT SIGNAL ADJUSTMENT CALIBRATION: 1. Supply a color bar signal and adjust the local frequency. 1. Connect the oscilloscope in TPL2 (G-OUT) with a 10KΩ 2. Adjust “IMAGE” to DYNAMIC NORMAL, “CONTRAST” to resistor and adjust “CONTRAST”, so that the [B] waveform...
TC-21FJ30LA ADJUSTMENTS ITEM / PREPARATION PROCEDURE 8- SUB-BRIGHT AND SUB-CONTRAST SUB-BRIGHT CALIBRATION CALIBRATION 1. Position the color analyzer in the LOW LIGHT image area. Supply a WINDOW pattern signal 2. Ajust S-BRT <CHK 4> control, so that it is Y=0,7±0.2.
TC-21FJ30LA ADJUSTMENTS ITEM / PREPARATION PROCEDURE 11- WHITE QUALITY CALIBRATION CALIBRATION: PREPARATION: 1. Adjust the magnetic field in 0.4x10-4T (400 mG), and check the white quality with the CRT turned to EAST and to WEST. 1. Adjust the HELMHOLTZ device to local magnetic field. Ho- 2.
TC-21FJ30LA ADJUSTMENTS ITEM / PREPARATION PROCEDURE 14- VERTICAL DEFLECTION CALIBRATION AND S-CORR CONFIRMATION AND CALIBRATION CONFIRMATION 1) Confirmation in 50Hz 1. Adjust IMAGE to DYNAMIC NORMAL 1. Supply a PHILIPS PAL-N signal. 2. Confirm that S-CORR 50Hz is in 33 DAC .
TC-21FJ30LA SIGNAL WAVEFORM • All waveforms were obtained using 127V 60Hz power source and Color Bars Pattern (Model: TC-20KL04) IC451 Pino 1 Pino 5 Pino 7 IC601 Pino 16 Pino 17 - 22 -...
TC-21FJ30LA REPLACEMENT MECHANICAL PARTS LIST Part No. Part Name & Description Ref. No. A51QDX993X004 PICTURE TUBE 21" (FLAT SAMSUNG) TKK4G8597 SPEAKER SUPPORT EASG15S02H2 SPEAKER TBM4G3013 PANASONIC LOGO TBX4G90110 POWER BUTTON TKP4G13030 CONTROL PANEL DOOR T-TKU2B22702 REAR COVER TLK4G9037X DEGAUSSING COIL...
TC-21FJ30LA REPLACEMENT ELECTRICAL PARTS LIST Part No. Part Name & Description Part No. Part Name & Description Ref. No. Ref. No. FULLY ASSEMBLED BOARDS C628 ECJ2YB1H473K CERAMIC CAP. 47,00 nF 50,0 V “A” PAL21FJ30LAMON “A”+“L” P.C.B. ASS´Y C631 ECJ2VB1H222K CERAMIC CAP. 2.200,00 PF 50,0 V “YUV”...
Page 29
TC-21FJ30LA Part No. Part Name & Description Part No. Part Name & Description Ref. No. Ref. No. C2113 ECA1HM4R7B ELECTROLYTICAL CAP. 4,70 µF 50,0 V D511 MAZ4108J0F ZENER DIODE 10,8 V 0,37 W 250,0 mA C2115 ECA1HM4R7B ELECTROLYTICAL CAP. 4,70 µF 50,0 V...
Page 30
TC-21FJ30LA Part No. Part Name & Description Part No. Part Name & Description Ref. No. Ref. No. L510 EXCELSA35T BEAD CORE R021 ERJ6GEYJ273V FILM RESISTOR 27,00 kOhm 1/8 W L511 EXCELSA35T BEAD CORE R022 ERJ6GEYJ473V FILM RESISTOR 47,00 kOhm 1/8 W...
Page 31
TC-21FJ30LA Part No. Part Name & Description Part No. Part Name & Description Ref. No. Ref. No. R605 ERJ6GEYJ101V FILM RESISTOR 100,00 Ohm 1/8 W R1141 ERJ6GEYJ562V FILM RESISTOR 5,60 kOhm 1/8 W R606 ERJ6GEYJ101V FILM RESISTOR 100,00 Ohm 1/8 W...