Advertisement
Table of Contents
Owner's Manual & Safety Instructions
Save This Manual
inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
1-1/8" VaRiaBlE SPEED
ROTARY HAMMER
00x
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
Copyright
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly, operating,
Visit our website at: http://www.harborfreight.com
Email our technical support at: tech@harborfreight.com
©
®
2011 by Harbor Freight Tools
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE thiS manual.
ITEM 69274
Advertisement
Table of Contents
Related Manuals for Chicago Electric 69274
Summary of Contents for Chicago Electric 69274
- Page 1 No portion of this manual or any artwork contained herein may be reproduced in Failure to do so can result in serious injury. any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing SaVE thiS manual.
-
Page 2: Table Of Contents
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Page 2 For technical questions, please call 1-800-444-3353. Item 69274... - Page 3 A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Item 69274 For technical questions, please call 1-800-444-3353. Page 3...
-
Page 4: Rotary Hammer Safety Warnings
• Do not use with power switch locked on. If unreadable or missing, contact • Properly maintain and inspect to avoid Harbor Freight Tools for a replacement. electrical shock. • Any power cord must be properly 7. avoid unintentional starting. - Page 5 If any abnormal seek medical advice as soon as possible. vibration occurs, stop use immediately. SaVE thESE inStRuCtiOnS. Item 69274 For technical questions, please call 1-800-444-3353. Page 5...
- Page 6 Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Outlets for 2-Prong Plug Page 6 For technical questions, please call 1-800-444-3353. Item 69274...
- Page 7 Do not cover ventilation ducts. Keep flammable objects away. n 0 xxxx/min. No Load Revolutions per Minute (RPM) WARNING marking concerning Risk of Electric Shock. Properly connect power cord to appropriate outlet. Item 69274 For technical questions, please call 1-800-444-3353. Page 7...
-
Page 8: Specifications
Parts List and Diagram on page 14. Functions Grease Port Auxiliary Trigger (101) Hammer Switch (54) Drill Switch (66) Handle (S-101) Chuck (3) Lock Knob (S-106) Speed Control (102) Figure a Page 8 For technical questions, please call 1-800-444-3353. Item 69274... -
Page 9: Operation
Chisel: Rotate the Drill Switch to the Drill OFF setting. Hammer Rotate the Hammer Switch to the Hammer ON setting. Switch The Rotary Hammer will hammer when powered. Figure D Item 69274 For technical questions, please call 1-800-444-3353. Page 9... - Page 10 4. Set the speed by rotating the Speed Control. the bit to cool then remove it from the Chuck. Clean, then store the tool indoors out of children’s reach. 5. Plug in the Power Cord. Page 10 For technical questions, please call 1-800-444-3353. Item 69274...
-
Page 11: Maintenance
Grease Port Cover Figure E: Grease Port Monthly, open the Grease Port, clean out old grease, and replace with new grease. CautiOn: Warranty void if grease maintenance is not maintained. Item 69274 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Troubleshooting
See Extension Cords in Grounding section on page 6. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Page 12 For technical questions, please call 1-800-444-3353. Item 69274... - Page 13 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 69274 For technical questions, please call 1-800-444-3353. Page 13...
-
Page 14: Parts List And Diagram
Needle Bearing Hk1210 S-103 Screw M8x40 Bearing 6001-2Z S-104 Clamp Ring Middle Cover Seal Ring S-105 Nut M6 Rubber Pin S-106 Lock Knob Steel Ball 4 S-107 Depth Gauge Hammer Switch Page 14 For technical questions, please call 1-800-444-3353. Item 69274... -
Page 15: Assembly Diagram
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 69274 For technical questions, please call 1-800-444-3353. Page 15... -
Page 16: Warranty
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the 69274 and is the answer not in the manual?
Questions and answers
how does the grease port plug come out
does it turn out or pry out
The grease port plug on Chicago Electric part number 69274 can be removed by opening the Grease Port. This should be done monthly to clean out old grease and replace it with new grease.
This answer is automatically generated
tool bit will not stay in the chuck
The tool bit may not stay in the chuck of the Chicago Electric 69274 because it is not properly secured. According to the manual, the drill bit should be inserted all the way into the chuck, and it should not be able to be pulled out if properly secured. If the bit is not fully inserted or if the chuck is not tightened correctly, the bit may come loose.
This answer is automatically generated