Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 69450
Summary of Contents for Central Pneumatic 69450
-
Page 2: Table Of Contents
National pipe thread, straight NIOSH-approved dust mask/respirator. WARNING marking concerning WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved Risk of Explosion. safety goggles with side shields. table a: Symbol Definitions Page 2 For technical questions, please call 1-800-444-3353. Item 69450... -
Page 3: Work Area
This is able to cause the fastener to be control of the tool in unexpected situations. deflected and hit someone, or cause the tool to react and result in a risk of injury to persons. Item 69450 For technical questions, please call 1-800-444-3353. Page 3... -
Page 4: Tool Use And Care
6. Do not remove, tamper with, or otherwise cause hard to penetrate. Do not drive fasteners on top the tool operating controls to become inoperable. of other fasteners, or at too steep of an angle. Page 4 For technical questions, please call 1-800-444-3353. Item 69450... - Page 5 7. To reduce vibration, maintain tool as explained as tingling, numbness, and white or blue fingers), in this manual. If abnormal vibration occurs, seek medical advice as soon as possible. stop immediately. SaVE thESE inStRuCtiOnS. Item 69450 For technical questions, please call 1-800-444-3353. Page 5...
-
Page 6: Specifications
Air Inlet 1/4″ -18 NPT Fastener Capacity Up to 3-1/2″ Long, 16d Air Consumption 1 CFM @ 90 PSI Components and Controls Air Inlet Guide Bushing Nail Guide Figure a Page 6 For technical questions, please call 1-800-444-3353. Item 69450... -
Page 7: Setup
However, it is a good safety measure to attempt to discharge the tool in a safe fashion after disconnecting to ensure that the tool is disconnected and unpowered. Item 69450 For technical questions, please call 1-800-444-3353. Page 7... - Page 8 Page 8 For technical questions, please call 1-800-444-3353. Item 69450...
- Page 9 Item 69450 For technical questions, please call 1-800-444-3353. Page 9...
- Page 10 Clean external surfaces with clean, dry cloth. tool and cause it to hammer the nail. Continue pressing down until the nail is driven all the way in. d. Store indoors out of children’s reach. Page 10 For technical questions, please call 1-800-444-3353. Item 69450...
-
Page 11: Operation
• cracked or broken parts, and supply will allow the tool to operate more safely • any other condition that may and will also reduce wear on the tool. affect its safe operation. Item 69450 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Troubleshooting
3. Replace damaged components. 4. Dirty, worn or damaged valve. 4. Clean or replace valve assembly. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Page 12 For technical questions, please call 1-800-444-3353. Item 69450... - Page 13 If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 69450 For technical questions, please call 1-800-444-3353. Page 13...
-
Page 14: Parts List And Diagram
Gasket Body O-Ring 38.1×2 Washer Joint Guider Restrict Bushing Assembly Slide Cover Spring O-Ring 41×1.8 Bushing Seal Ring Guide Bushing Cylinder Filter Air Plug O-Ring 30.1×1.8 Air Plug O-Ring 30×2.5 Page 14 For technical questions, please call 1-800-444-3353. Item 69450... -
Page 15: Warranty
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. - Page 16 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353...