Page 2
When changes occur in applicable products or in the content of this manual, Canon will release service manual report as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon may issue new editions of this manual.
SAFETY PRECAUTIONS The following precautions should be observed when servicing. Since many parts in the unit have special safety-related characteristics, always use genuine CANON replacement parts. Especially critical parts in the power circuit block should not be replaced with other makes.
1-1 Development Objectives As of November 2001, Canon is responding to a wide range of customer demands with the six series in our line: the single-lens-reflex EOS 1D and EOS D30, the PowerShot Pro90 IS with 10x zoom lens, the PowerShot G2 with high image quality and advanced features, the highly compact PowerShot S40/S30, the ultra compact IXY DIGITAL 300/200 and the basic value PowerShot A20/A10.
Page 8
Full Features / Operation Ease - Photo Effect Modes (Vivid color, Neutral color, Low Sharpening, Sepia and Black & White) are provided - Direct Print Function for dedicated printers (CP-10 Card Photo Printer and CP-100 Photo Printer) - Shutter speed is allowed from 1 to 1/2000 sec. - Enabling for On/Off selection of AF-assist Beam - Macro Function focuses down to 5 cm - Use of widely available size AA battery (2) (primary: alkaline, secondary: NiCd/NiMH)
- Compact power adapter for power supply - Full featured application softwares Canon Image Gateway* compliance for image upload, album creation, on-line photo printing, etc*. ZoomBrowser EX 3.3/3.4 (Win)/ImageBrowser 2.3 (Mac) featuring improved ease of operation PhotoRecord 1.4 (Win) for easy layout and printing of pictures PhotoStitch 3.1 for creating precise panoramic pictures...
Direct Print Function for dedicated printers (CP-10 Card Photo Printer and CP-100 Photo Printer) The PowerShot A200/A100 includes the Direct Print function to enable high quality image printing by connect- ing with a special cable to Canon’s CP-10 Card Photo Printer and CP-100 Photo Printer, newly developed for postcard size prints.
Page 12
The PowerShot A200/A100 includes a macro function that can photograph as close as 5 cm from the subject. The area of the photo is about 46 × 34 mm with the PowerShot A200, and about 47 × 35 mm with the PowerShot A100, 46 mm/1.8 inch which is the smallest area that can be photographed so far by any camera in Photo 2-2 Max.
Page 13
High speed continuous shooting (approx. 3 images/sec.(PA A100) when LCD monitor is off) The PowerShot A100 can shoot continuous pictures at up to approx. 3 images per second (PS A200 : approx. 2 images per second). The maximum number of continuous images that can be taken are 10 (PS A100), 7 (PS A200) in the Large/Fine mode.
Page 14
PowerShot A100 incorporates 3.2x digital zoom. So the 1600X1200 PowerShot A200 functions as a 39-156 mm zoom equivalent, and the PowerShot A100 as a 39-125 mm zoom equivalent 1280X960 (relative to a 35-mm film camera). However, because of the PowerShot A200...
Page 15
Immediate image review (can erase while reviewing) The PowerShot/IXY series displays an image for two seconds (or ten seconds, depending on setting)* for confirmation immediately after the photo is taken. The PowerShot A200/A100 supplements this feature with the Erase One Image mode, activated by the button with the same name. This feature allows an undesired image to be erased immediately after the photo is taken, so it does not take up memory space.
The PowerShot A200 adopts the newly developed 1/3.2-type 2-megapixel* CCD (1.2-megapixels for the PowerShot A100). These CCDs have almost the same number of pixels as those in the PowerShot A20/A10, but the screen size is reduced from 1/2.7 type to 1/3.2 type, making the smaller optical system possible.
Page 17
AF maintains image focus at any distance Although most cameras in this class typically use fixed-focal-length (pan) focus, the PowerShot A200/A100 is equipped with high-precision AF. This allows sharp images to be obtained regardless of distance to photographic subject. Also, the normally unusable focal range for most such cameras between the macro focal plane and the minimum normal focal plane from 5 cm to infinity, becomes possible.
Graphical symbols representing the basic camera functions are printed on the top of the screen of the PowerShot A200/A100 cameras. The basic functions are this easy to see at a glance on the store shelf, and serve to accent the design. Photo 2-5 PowerShot A100 Fig. 2-9 Graphical symbols at the top 1-12...
The PowerShot A200/A100 can be powered from household power source using the CA-PS800 Compact Power Adapter. Full featured application software Usage of Canon Image Gateway When an PowerShot A100/A200 purchaser registers as a member, they can receive the following on-line photo services at Canon Image Gateway: -Image upload service -On-line photo album service...
Page 20
Twain Driver 4.3(A100)/4.5(A200) / WIA Driver 4.3(A100)/4.5(A200) (Win) Unchanged from previous version, for convenience. Plug-in module 4.3(A100)/4.5(A200) / USB mounter 1.4(A100)/1.6(A200) (Mac) Unchanged from previous version, for convenience. RAW Image Converter 2.0(A100) for processing RAW images From this version, the TWAIN driver and UI share the same development prosess. Also, loading RAW data into ZoomBrowser EX 3.3/3.4 (Win) and ImageBrowser 2.3 (Mac) causes RAW Image Converter 2.0 to load automatically for developing and saving the data.
3 Exterior 3-1 Camera Bright-silver Smoke-gray Photo 3-1 PowerShot A200 front Titanium-metalic Photo 3-2 PowerShot A200 rear Photo 3-3 PowerShot A200 top * These photos have slightly different exterior from mass-production model because of prototype. 1-15...
Page 22
Bright-silver Smoke-blue Photo 3-4 PowerShot A100 front Titanium-metalic Photo 3-5 PowerShot A100 rear Photo 3-6 PowerShot A200/A100 operation part * These photos have slightly different exterior from mass-production model because of prototype. 1-16...
3-4 User Interface display Rec.Menu <Digital Zoom> <Resolution> <Compression> L : 1280X960 Super Fine On/ Off (A100 Rec.mode: Auto) M : 1024X768 Fine S : 640X480 Normal <Review> <AF-assist Beam> <File No. Reset> Off/ 2Sec./ 10Sec. On/ Off On/ Off Set up...
Page 27
DPOF <Order> <Set up> Print (order) <File No> <Print Type> <Date> Transfer Order (DPOF) Standard On/ Off On/ Off Index Both Transfer Mark all 1-21...
4 Specifications 4-1 Camera Specifications ( PowerShot A200 ) ( PowerShot A100 ) <Camera effective pixels> Approx. 2 million Approx. 1.2 million <CCD> -Reading format Interline << -Image size 4.48 (H) X 3.38 (V) mm 4.48 (H) X 3.36 (V) mm (0.18 X 0.13 in.
Page 29
<Aperture and shutter> -Shutter type Mechanical shutter and electronic shutter -Shutter speed 1 - 1/2,000 sec. (1 - 1/6 sec. shutter is available at flash-off or slow-syncro. in Manual mode.) (Slow shutter of 1/6 sec. and more operates with noise reduction.) f/2.8 / f/5.6 -Aperture range <White balance>...
Page 30
(When “All images” is set, any images in the CF card captured with another digital camera or peripheral device (DCF format) are erased. Regarding Canon digital cameras, images taken by PowerShot Pro70 or prior models are not erased. Images taken by PowerShot A50 (DCF format) or latest models are erased (except EOS D2000/D6000).
Page 31
-Playback time Size AA / NiMH battery (NB-1AH) : Approx. 120 min. * Canon’s standard conditions of measuring playback time are as follows: Normal temperature (23 Celsius degrees). Repeat playback automatically at a speed of 1 image per 3 seconds.
Page 32
Parameter availability by modes Auto Manual Stitch Movie Auto Red-eye reduction auto Flash Slow-syncro. Macro Single Shooting Continuous Self-timer Photo effect AF frame selection 3 points(AiAF) 1 point Exposure compensation White balance Auto only Recording pixels Movie(320×240) Movie(160×120) Superfine Compression level Fine Normal JPEG...
Playback compatibility Playback compatibility of PowerShot/IXY DIGITAL series is as follows. PowerShot A200/A100 can accept 3200(H) X 2400(V) pixels. Playback Cameras PS A5/A5 PS G1 IXY D PS A200 PS 350 PS Pro70 PS A50 EOS D30 PS G2 S10/S20 DIGITAL Pro90 IS 200/300...
4-2 System Requirements Windows Macintosh -Windows 98 (including SE) -Mac OS from 8.6 to 9.2 (PS A100) -Windows 2000 -Mac OS from 8.6 to 10.1 (PS A200) * * unavailable of Mac OS 10.0 -Windows Me * unavailable with Mac OS 10.1 at UFS (Unix File System) *Windows XP -USB Mounter is available with Mac OS 9.0 to 9.2 Pentium 150MHz and over...
4-3 Specifications of Major Accessories Compact Power Adapter CA-PS800 • Rated input : 100 - 240 V AC (50/60 Hz) 16 VA (100 V) - 26 VA (240 V) • Rated output: 3.15 V DC, 2 A • Ambient temperature : 0 - 40 ºC •...
Page 36
Interface Cable IFC-300PCU • USB Series A 4-pin connector - Series mini - B 5-pin connector Unit : mm (inch) • The dimensions are shown in Fig. 4-4. 15.8(0.62) 24.3 12.2(0.78) 38.5(1.52) (0.96) 7.0 (0.27) Fig. 4-4 Interface Cable IFC-300PCU Direct Interface Cable DIF-100 •...
Page 41
CHAPTER 2. TECHNICAL DESCRIPTION CONTENTS 1. Functions of each unit 1.1 MAIN PCB ASS’Y --------------------------------------------------------------------------------------------------------- 2-1 1.2 FLASH UNIT ---------------------------------------------------------------------------------------------------------------- 2-1 2. Outline of Circuits 2.1 Power Supply Control ------------------------------------------------------------------------------------------------------ 2-2 2.1.1 Power Supply Block Diagram ----------------------------------------------------------------------------------- 2-2 2.1.2 Power Control Sequence ------------------------------------------------------------------------------------------ 2-2 2.2 Signal Processing ------------------------------------------------------------------------------------------------------------ 2-3 2.2.1 System Control ----------------------------------------------------------------------------------------------------- 2-3...
CHAPTER 2. TECHNICAL DESCRIPTION 1. Functions of each unit 1.1 MAIN PCB ASS’Y 1) Driving the CCD Sensor. 2) Conversion of the image signal from the analog signal to the digital signal. 3) Controlling the power supply and the system by CPU. (Refer to Sections 2.1 and 2.2.) 4) Image processing, and reading and writing the image signal to and from the CF card using DSP.
CHAPTER 2. TECHNICAL DESCRIPTION 2. Outline of Circuits 2.1 Power Supply Control The power supply is controlled by the CPU mounted on the main PCB ass’y. 2.1.1 Power Supply Block Diagram MAIN PCB ASS'Y E1, E2, E3 (2.5V) for DSP BATTERY (2.5V) DC/DC...
CHAPTER 2. TECHNICAL DESCRIPTION 2.2 Signal Processing MAIN PCB ASS'Y SDRAM CF card HD, VD Drive Pulse Driver CDS, A/D Sensor Motor EF LENS Driver AF Support LED FLASH MEMORY FINDER LED Buzzer Electric FLASH Fig. 3 Signal System Block Diagram 2.2.1 System Control The CPU on the main PCB ass’y controls the EF lens (motor, shutter), operation switch receiver, USB communication and flowing circuits.
CHAPTER 2. TECHNICAL DESCRIPTION 2.2.2 Picture Processing 1) The drive pulse of the CCD sensor is created by both clock from DSP and TG that is operated by sync. signal. The picture signal by the drive pulse is output from CCD sensor. The output signal of the CCD picture is converted to the signal processing and the digital data by the CDS and A/D converter, and is sent to the DSP.
CHAPTER 2. TECHNICAL DESCRIPTION 3. Troubleshooting 3.1 When an Error Code is Displayed [Remedy] • Check for any abnormalities in the mounting of probable faulty parts or connector connections referring to the table below. • Try replacing probable faulty parts referring to the below. [NOTE] •...
Page 48
CHAPTER 2. TECHNICAL DESCRIPTION Error Code Name Occurrence Conditions Cause and Probable Faulty Part CF WRITE Free area could not be secured in the CF CARD TIME OVER buffer for the photograph image within the specified time in the continuous MAIN PCB ASS’Y shooting mode.
CHAPTER 2. TECHNICAL DESCRIPTION 3.2 When a Problem Occurs [Remedy] • Check for any abnormalities in the mounting of probable faulty parts or connector connections referring to the table below. • Try replacing probable faulty parts referring to the table below. [NOTE] •...
Page 51
CHAPTER 3. REPAIR INSTRUCTION CONTENTS 1. Before Starting the Repair Work 1.1 Precaution on Flash High Tension Circuit ------------------------------------------------------------------------------- 3-1 1.2 List of Tools ----------------------------------------------------------------------------------------------------------------- 3-1 1.3 List of Supplies -------------------------------------------------------------------------------------------------------------- 3-1 1.4 Flexible Connectors --------------------------------------------------------------------------------------------------------- 3-2 2. Disassembly/Assembly 2.1 Procedure --------------------------------------------------------------------------------------------------------------------- 3-3 2.2 REAR COVER UNIT ------------------------------------------------------------------------------------------------------ 3-4 2.3 FRONT COVER UNIT, BATTERY COVER -------------------------------------------------------------------------- 3-5 2.4 BACKLIGHT UNIT, LCD PANEL -------------------------------------------------------------------------------------- 3-6...
CHAPTER 3. REPAIR INSTRUCTION 1. Before Starting the Repair Work Be sure to read the following precaution before starting the repair work. 1.1 Precaution on Flash High Tension Circuit • When the FRONT COVER UNIT and REAR COVER UNIT are removed, be sure to discharge the main capacitor.
CHAPTER 3. REPAIR INSTRUCTION 1.4 Flexible Connectors This product uses the three types of the flexible connectors. 1 Type A UNLOCK LOCK The contact-piece should face downwards Unlocked state Locked state 2 Type B UNLOCK LOCK The contact-piece should face upwards Unlocked state Locked state...
CHAPTER 3. REPAIR INSTRUCTION 2. Disassembly/Assembly 2.1 Procedure Disassembling procedure of PowerShot A100/A200 is shown by the following flowchart. Reverse the disassembling procedure to reassemble them. ∗ The pages to refer are shown in parenthesis ( ). BACKLIGHT UNIT (2-4)
CHAPTER 3. REPAIR INSTRUCTION Soldering MAIN SHIELD CASE 2 Fig. 3-7 MAIN SHIELD CASE 2 2.5 MAIN SHIELD CASE 2 (1) MAIN SHIELD CASE 2 1. Remove soldering at four locations. 2. Remove the MAIN SHIELD CASE 2.
CHAPTER 3. REPAIR INSTRUCTION RLS PCB ASS'Y (1)-2 (1)-2 M-R FPC ST PCB ASS'Y MAIN PCB ASS'Y (1)-1 (1)-1 M-S FPC NOTE (Assembling) M-S FPC Fig. 3-8 M-S FPC, M-R FPC 2.6 M-S FPC, M-R FPC (1) M-S FPC 1. Disconnect the M-S FPC from the connector on the ST PCB ASS’Y and the connector of the MAIN PCB ASS’Y.
CHAPTER 3. REPAIR INSTRUCTION MAIN SHIELD CASE 3 MAIN PCB ASS'Y (1)-1 (1)-2 Soldering MAIN SHIELD CASE 1 (2)-2 Soldering EM1 SHEET (2)-1 (2)-2 Soldering Fig. 3-10 MAIN SHIELD CASE 3, MAIN SHIELD CASE 1 2.8 MAIN SHIELD CASE 3, MAIN SHIELD CASE 1 (1) MAIN SHIELD CASE 3 1.
CHAPTER 3. REPAIR INSTRUCTION Discharge of Capasitor CAUTION Do not touch the terminals of the discharging capasitor.Be sure to discharge NOTE (Assembling) OPTICAL UNIT the main capasitor with a discharge resistor. MAIN FRAME (1 k ohms, approx.5 W) terminal BATTERY LEAD Orange (2)-2 MICROPHONE LEAD...
CHAPTER 3. REPAIR INSTRUCTION MAIN FRAME NOTE (Assembling) Positioning when assembling (1)-2 OPTICAL UNIT (1)-1 XA4-9170-407 4.0mm METAL M1.7 (SELF TAP) Fig. 3-13 OPTICAL UNIT 2.11 OPTICAL UNIT (1) OPTICAL UNIT 1. Remove the three screws c. 2. Remove the OPTICAL UNIT in the direction of the arrow. NOTE (Assembling) Align the two positioning dowels of the MAIN FRAME at each location.
3. Adjustments 3.1 Replacement Parts and Adjustment Items PowerShot A100/A200 requires electrical adjustments when certain parts are replaced. The table below indicates the adjustments required for the respective part replacements. For all other parts not listed below, no electrical adjustments are necessary after replacement.
Print the Auto Focus Chart on the legal size paper from the “AFChart_Legal.pdf ” (in the folder of this CD-ROM, :\Adjust\Chart). Print the Auto Focus Chart on the A3 size paper from the “AFChart_A3.pdf ”. Make use of the Auto Focus Chart for the PowerShot A100/A200. 2pcs. required. 3-19...
CHAPTER 3. REPAIR INSTRUCTION 3.3 Before Starting Electrical Adjustments 3.3.1 TWAIN Driver Installation Install the USB Driver for Adjustment in the CD-ROM to PC. (“This Adjustment Software” is impossible when the RS-232C TWAIN driver is used.) 3.3.2 Installing the Adjustment Software 1.
Page 73
CHAPTER 3. REPAIR INSTRUCTION 3. When the dialog box below appears, click the button. (Software installation will then begin.) 4. When the dialog box below appears, click the “Continue” button. (In the case that you do not add a shortcut on desktop, remove clicking from the check box.) 3-21...
CHAPTER 3. REPAIR INSTRUCTION 3.3.3 Preparation Before starting up the Adjustment Software, follow the preparatory steps below: 1. Obtain all the tools necessary for the adjustment. 2. Connect the Camera to the Power Source with the Compact Power Adapter CA-PS800. 3.
CHAPTER 3. REPAIR INSTRUCTION 3.3.4 Starting up the Adjustment Software After completing the preparatory steps, click Start and move the cursor to Program; then select Canon Digital Camera and click PowerShot A100/A200 Adjustment. 3.3.5 Menu Window When the Adjustment Software starts up, the Menu Window below will appear.
CHAPTER 3. REPAIR INSTRUCTION 3.4 Calibration 3.4.1 Calibration I Tools Used • Reference Camera (Merchandise) • Personal Computer • ND-8 Filter • Compact Power Adapter CA-PS800 • Color Viewer (5600° K) • ND-2 or ND-4 Filter • Adjustment Software • C-12 Filter •...
Page 77
2. Place the camera so that the lens is set against CAMERA BODY the center part of the Color Viewer. 3. Click the “ADJUST” button. Power * PowerShot A100 : ND-4 Source PowerShot A200 : ND-2 Stand Personal Computer 3-25...
Page 78
CHAPTER 3. REPAIR INSTRUCTION When the message on the right appears go to 9. W-10 1. Remove the ND Filter. Filter 2. Attach the two W-10 Filters between the Lens Color Viewer CAMERA and the Color Viewer. BODY Place the camera so that the lens is set against the center part of the Color Viewer.
Page 79
2. Place the camera so that the Viewing image of the color bar chart is the full of LCD with the ND Filter* attached. ND-4 or ND-2 3. Click the “ADJUST” button. Filter CAMERA * PowerShot A100 : ND-4 BODY PowerShot A200 : ND-2 Power Source Personal Stand Computer 1.
Page 80
CHAPTER 3. REPAIR INSTRUCTION When the message on the right appears, click the “FINISH” button. (This ends the “Calibration”.) 3-28...
CHAPTER 3. REPAIR INSTRUCTION 3.5 Adjustment Procedure 3.5.1 CCD Adjustment I Tools Used • Personal Computer • Adjustment Software • INTERFACE CABLE IFC-300PCU • Compact Power Adapter CA-PS800 • Brightness Box (light source A) • C-12 Filter Click the “CCD” button. When the message on the right appears, go to 3.
Page 82
CHAPTER 3. REPAIR INSTRUCTION When the message on the right appears, Set the Brightness Box to EV15 while setting the C-12 Filter between the lens. Click the “ADJUST” button. When the message on the right appears, click the “FINISH” button. (This ends the “CCD”...
CHAPTER 3. REPAIR INSTRUCTION 3.5.2 Optical Unit Adjustment I Tools Used • Personal Computer • Tripod • INTERFACE CABLE IFC-300PCU • Adjustment Software • AF Chart • Compact Power Adapter CA-PS800 Click the “Optical Unit” button. When the message on the right appears, go to 3. 1.
Page 84
CHAPTER 3. REPAIR INSTRUCTION When the message on the right appears, click the “FINISH” button. (This ends the “Optical Unit” Adjustment.) 3-32...
2. Place the camera so that the lens is set against CAMERA BODY the center part of the Color Viewer. 3. Click the “ADJUST” button. Power * PowerShot A100 : ND-4 Source PowerShot A200 : ND-2 Stand Personal Computer 3-33...
Page 86
CHAPTER 3. REPAIR INSTRUCTION When the message on the right appears, go to 5. W-10 1. Remove the ND Filter. Filter 2. Attach the two W-10 Filters. Color Viewer Place the camera so that the lens is set against CAMERA BODY the center part of the Color Viewer.
Page 87
2. Place the camera so that the viewing image of the color bar chart is the full of LCD with the ND Filter* attached. ND-4 or ND-2 3. Click the “ADJUST” button. Filter CAMERA * PowerShot A100 : ND-4 BODY PowerShot A200 : ND-2 Power Source Personal Stand Computer 1.
Page 88
CHAPTER 3. REPAIR INSTRUCTION 1. Confirm to see that the image on the PC moni- tor satisfies the specifications. 2. If the image on the PC monitor does not satisfy the specifications, change the data using UP, DOWN button or change the data directly by typing the data in the text box.
CHAPTER 3. REPAIR INSTRUCTION 3.5.4 Pixel Dot Adjustment I Tools Used • Personal Computer • Compact Power Adapter CA-PS800 • INTERFACE CABLE IFC-300PCU • Adjustment Software • Brightness Box (light source A) • C-12 Filter • Light-Shielding Cloth (500 × 500 or larger) •...
Page 90
CHAPTER 3. REPAIR INSTRUCTION 1. When the message on the right appears, cover the camera with the Light-Shielding Cloth so that the no light reasons the CCD. 2. Click the “ADJUST” button. When the message on the right appears, click the “FINISH”...
CHAPTER 3. REPAIR INSTRUCTION 3.5.5 Flash Adjustment I Tools Used • Personal Computer • Compact Power Adapter CA-PS800 • 18% Gray Chart • INTERFACE CABLE IFC-300PCU • Adjustment Software • Tripod Click the “Flash” button. When the message on the right appears, go to 3. 1.
Page 92
CHAPTER 3. REPAIR INSTRUCTION When the message on the right appears, click the “FINISH” button. (This ends the “Flash” Adjustment.) 3-40...
Page 93
CHAPTER 3. REPAIR INSTRUCTION 3.5.6 Language (For Oth) I Tools Used • Personal Computer • Compact Power Adapter CA-PS800 • INTERFACE CABLE IFC-300PCU • Adjustment Software (FontSet.exe) Open the “FontSet.exe” and click the “New Connection” button. When the message on the right appears, confirm the model name, and click the “OK”...
Page 94
CHAPTER 3. REPAIR INSTRUCTION *Make sure to appear “err:0 on the bottom line. 3-42...
Page 95
CHAPTER 4. PARTS CATALOG CONTENTS PowerShot A200/PowerShot A100 Casing Parts ----------------------------------------------------------------------------------------------------------------------- Pg1 Internal Parts ---------------------------------------------------------------------------------------------------------------------- Pg2 Accessories-1 ------------------------------------------------------------------------------------------------------------------------- Pg3 Accessories-2 ------------------------------------------------------------------------------------------------------------------------- Pg4 Accessories-3 ------------------------------------------------------------------------------------------------------------------------- Pg5 Service Tools -------------------------------------------------------------------------------------------------------------------------- Pg6 Category of CLASS A: Frequency of use: High B: Frequency of use: Middle...
Page 98
PowerShot A200 PowerShot A100 P A R T S L I S T SYMBOL PARTS NO. CLASS QTY D E S C R I P T I O N R E M A R K S CM1-1307-000 FRONT COVER UNIT...
Page 100
PowerShot A200 PowerShot A100 P A R T S L I S T SYMBOL PARTS NO. CLASS QTY D E S C R I P T I O N R E M A R K S CY1-6156-000 OPTICAL UNIT YN1-1936-000...
Page 101
PowerShot A200 PowerShot A100 Accessories-1 Wrist Strap WS-200 USB Interface Cable CF Card FC-8M IFC-300PCU Alkaline Batteries (X2) Canon Digital Camera AC Cable Solution Disk N.Sl : N.S Stand for No Stock (Product available)
Page 102
PowerShot A200 PowerShot A100 P A R T S L I S T SYMBOL PARTS NO. CLASS QTY D E S C R I P T I O N R E M A R K S C84-1060-000 WRIST STRAP WS-200 C84-1115-000 CD-ROM, SOLUTION DISK VER.9.0 (J/E) PS A100...
Page 103
PowerShot A200 PowerShot A100 Accessories-2 Water proof Case WP-DC400 Water proof Seal Grease Packing Protector Moisture Neck Strap Wrist Strap Diffusion Plate Unit N.Sl : N.S Stand for No Stock (Product available)
Page 104
PowerShot A200 PowerShot A100 P A R T S L I S T SYMBOL PARTS NO. CLASS QTY D E S C R I P T I O N R E M A R K S CY1-6175-000 PACKING, RUBBER, WP-DC400...
Page 105
PowerShot A200 PowerShot A100 Accessories-3 Camera User Guide Software Starter Guide System Map...
Page 106
PowerShot A200 PowerShot A100 P A R T S L I S T SYMBOL PARTS NO. CLASS QTY D E S C R I P T I O N R E M A R K S CDI-J036-000 I.BOOK (J) PS A100...
Page 107
PowerShot A200 PowerShot A100 Se rv ice T ool s DIA BOND NO.1663G BLACK W-10 Filter Adhesive Tape SONY T4000 18% Gray Chart Adhesive Tape 3M NO.56 SERVICE MANUAL CD-ROM C-12 Filter...
Page 108
PowerShot A200 PowerShot A100 P A R T S L I S T SYMBOL PARTS NO. CLASS QTY D E S C R I P T I O N R E M A R K S CY9-8129-000 BOND, DIA BOND NO.1663G BLACK...
CN1011 CN1702 DC IN CN104 FU101 CN1502 FLASH UNIT BATTERY BL FPC ASS’Y REAR COVER UNIT Barrier close LCD PANEL Detect SW BACK LIGHT UNIT Barrier open Detect SW BUZZER CN201 (Direct solder) 01 June, 2002 C CANON INC., 2002...
Page 113
/CE2 /VS1 VDDG /IORD VSSG /IOWR Not Connected WIDE IREQ Not Connected Not Connected /VS2 CEXT/REXT RESET HCK2 /WAIT HCK1 Not Connected PSIG /REG GREEN Not Connected Not Connected BLUE Not Connected D110 01 June, 2002 C CANON INC., 2002...
BACK LIGHT REAR COVER UNIT UNIT (2/3) CN1503 for System Control for Motor for CCD for LCD Control FLASH UNIT FLASH HV/OSC/XE_Drive DC/DC CONVERTER AF Support BATTERY BOX UNIT SELF Red Eye DC_IN 01 June, 2002 C CANON INC., 2002...
Page 116
CXIN VCC2_AD AIN 4 VCC 3 AIN 5 VBAT TEMP X1001 AIN6 AIN 6 IC1003 24MHz AND GATE VCC_CF AIN 7 OSC1_X1 TC7SH08FU OSC1_X2 E1LAT EX35 E2LAT EX36 EX36 E3LAT EX37 EX37 VCHGLVL 01 June, 2002 C CANON INC., 2002...
Page 117
SI3445DV UNIT Q1017,Q1016 DTC144EE EX43 CN1008 Barrier Close EX54 Q1018 BRCL Q1016-Q1018 2SC4617 SCAN CF POWER CONT BROP EX28-31 5 VBATT_R Barrier Open EX35 BR FPC EIPLAT FRONT COVER BACK LIGHT UNIT UNIT 01 June, 2002 C CANON INC., 2002...
Page 118
T101 2 Q102 FU102 EF Charge 2SB1197K Q104 CN104 XE Drive CY20AAJ-B STSP EFCHG Q203 EFCHG T102 VCHGLVL 2SC4672 Q101 SW From DTC144EE MAIN PCB ASS’Y AF Support VCHGLVL SELF STSP Red Eye LED_SFLF 01 June, 2002 C CANON INC., 2002...
2.6 Abbreviation in Block Diagrams Abbreviation Nominal name Description Analog-to-Digital (A/D) Converter Automatic Exposure control Automatic Focussing control Logic AND circuit R-Y/B-Y Color difference signals of TV system Band-Pass Filter BUFFER Buffer circuit Chrominance signal Color component signal of TV system Charge-Coupled Device CCD imager Correlated Double Sampling system...
Page 125
How to print out the AF Chart The large materials such as “AF Chart” that occupy a page of large size, can be divided into several smaller pages using “Graphic Select Tool” for printing the entire page. < Procedures > 1.