Equalizer Section - Panasonic WR-DA7 Service Manual

EQUALIZER Section

4
Q (quality) parameter
knob or left surround
sound attenuator
-
FREQ (frequency)
parameter knob or
surround left surround
-
sound attenuator
GAIN parameter knob
or subwoofer surround
sound attenuator
-
EQUALIZER Section
There are three parameter knobs and four frequency range
LED buttons in the EQUALIZER section, which are used to
change the EQ settings of the currently selected channel.
The EQ ON LED button toggles the EQUALIZER on (green)
and off. When the controls are active, adjustments can be
made to the currently selected channel.
The three knobs are labeled Q (quality), FREQ (frequency),
and GAIN (gain). The additional labeling of
(surround left), and
SUB
surround sound parameters that are controlled by the knobs
when the [SURROUND] mixing area is activated. Surround
sound capabilities are discussed in Chapter 8.
The four frequency band LED buttons can be selected one
at a time, and turn on ( orange ) to show which band is
operating. They are labeled H (high), HM (high-mid), LM
(low-mid), and L (low).
Pressing the GAIN knob displays the [EQUALIZER] window
on the LCD screen. Once the [EQUALIZER] is displayed in
the LCD window, these buttons perform other shortcut
functions.
The EQUALIZER section is detailed in Chapter 7 in the
Users' Guide.
PAN/ASSIGN/
5
Section
PAN parameter
knob or center
surround sound
attenuator
PAN ON LED button
MASTER L/R LED
button
DIRECT LED button
PAN/ASSIGN/
EQUALIZER
H
+
Q
L
HM
Frequency band
LED buttons
LM
+
FREQ
SL
EQ ON LED
EQ
L
button
+
ON
GAIN
SUB
(left),
L
(surround subwoofer) indicate the
, BUS ASSIGN
BUS
ASSIGN
LED
buttons
, BUS ASSIGN Section
Pan, bus assignment, and surround sound parameters for
the selected channel is set within this area. The pan control
is always active for the L/R bus, so you do not need to
activate the ON button to pan across the Master L/R out.
However, if you wish to pan between odd/even buses, you
must push the ON button. Assignment to the DIRECT output
is not affected by the pan control.
The additional labeling of
surround sound parameter that is controlled by the knob
when the [SURROUND] mixing area is activated.
The L/R, the DIRECT, and the BUS ASSIGN LED buttons
toggle on ( green ) and off. In addition to the eight bus
selections, labeled 1 - 8, selections for L/R (master L/R)
output and DIRECT output are available. The DIRECT
output works in conjunction with the option cards installed in
the DA7 Rear Panel, routing signals directly to the cards.
The DIRECT output is detailed in Chapter 12, D-I/O (Digital
Input/Output) in the Users' Guide.
Pressing the PAN knob displays the [SURROUND] window
on the LCD screen.
The PAN/ASSIGN/
Top Panel is detailed in Chapter 8 in the Users' Guide.
S L
DYNAMICS/DELAY Section
6
THL (threshold),
ATK(attack), DLY
(delay) parameter knob
or right surround sound
attenuator
RATIO, RLS (release),
GAIN parameter knob
or surround right
surround sound
attenuator
DYNAMICS ON LED
button
DYNAMICS and/or DELAY processing can be added to
each of the DA7 Channels. Pressing the PARAMETER
SELECT button cycles the current parameter selections,
which are grouped in pairs. The top knob adjusts the top
parameter selection in the pair, and the bottom knob adjusts
the bottom parameter selection in the pair. The DYNAMICS
ON LED button toggles the dynamics processing on ( green )
and off for the selected channel, and the DELAY ON LED
button toggles the delay on ( green ) and off.
The additional labeling of
right) indicates the surround sound parameters that are
controlled by the knobs when the [SURROUND SOUND]
mixing area is activated. The surround sound function is
activated in the [SURROUND] window of the [SURROUND]
window group.
3
(center) indicates the
C
, BUS ASSIGN section of the
DYNAMICS/DELAY Section
R (right) and
PARAMETER
SELECT
LEDs
PARAMETER
SELECT
button
DELAY ON
LED button
SR (surround