Sony DCR-DVD201 Service Manual page 14

DCR-DVD201/DVD201E
7
V C
- 3 5
4
8
qa
4
0
B
D
D
3
5
B
2 6
9
D
1
1 Screw (M1.7x2.5) silver 6 Two EG grip screws (M1.7x4) black
2 VC heat sink, VC radiation sheet, 7 Control switch block (PS8700) (20P)
VC insulating sheet 8 Battery terminal board (3P)
3 Screw (M1.7x2.5) silver 9 Battery terminal board
4 Claw 0 FP-887 flexible board (8P)
5 Screw (M1.7x2.5) silver qa Square type connector (USB 5P),
FP-887 flexible board
2
1 Two tapping screws (M1.7x5) black
2 Remove the D lid assembly
in the direction of the arrow.
B
A
Screw Screw
M1.7x3 M1.7x4
3-084-817-21 3-087-376-01
C D
Tapping screw Screw
M1.7x3.5 M1.7x2.5
3-078-889-11
3-078-890-01
E
Silver
Tapping screw
Black
M1.7x5
3-081-204-21
2
3
4
- 3 5
V C
4
1
D
1 Three screws (M1.7x2.5) silver
2 Board to board (CN1007,CN4901) (100P)
3 Radiation sheet (135)
4 VC-354 board
3
c
b
E
1 2
a
1
1 Remove the grip belt
in the direction of the arrow a.
2 Push this portion with a finger
in the direction of the arrow b.
3 Open the D lid assembly
in the direction of the arrow c.
1
4
1 Remove the grip belt
in the direction of the arrow.
2 Two tapping screw (M1.7x3.5) silver
3 Grip belt sheet metal (Rear)
4 Grip belt
2-3
2. DISASSEMBLY
2. DISASSEMBLY
4
4
- 1 0
2
M D
3
D
1
1 Screw (M1.7x2.5) silver
2 VM heat sink, VM radiation sheet, VM insulating sheet
3 Tripod large
4 Sheet radiation (2345)
2
1
E
1 Two tapping screws (M1.7x5) black
2 D blind plate assembly
3
2
C
E
C
HELP 03
1
2
3
1 Two tapping screws (M1.7x5) black
2 Tapping screw (M1.7x3.5) silver
3 Control switch block (PS8700)
Caution
Use the adjustable wrist strap (J-2501-162-A) as the
Precautions during handling preventive measure for static electricity when the
removing and installing the MD black assembly because
Be sure to place the DVD drive with its
the MD black assembly of this mechanism beck is easily
optical pickup facing upward.
affected by the static electricity.
Do not touch the optical pickup surface.
Optical pickup
1
D
6 5
7
3
E
4
C
D - 1 0
4
M D
2
Refer to level 3
8
Disassembling procedure of
MD block assembly.
1 Two screws (M1.7x2.5) silver 5 DC-IN connector inlet (3P)
2 Screw (M1.7x2.5) silver 6 Harness (DM-144) (2P) (Dew sensor)
3 Three tapping screws (M1.7x5) black 7 FP-891 flexible board (10P)
4 Tapping screw (M1.7x3.5) silver 8 Remove the MD block assembly in the
direction of the arrow.
1
b a
2
4
3
1 Open the jack cover (DC) in the directions of the arrows a and b.
2 DC-IN connector inlet
3 Harness (DM-144), FP-228 flexible board (Dew senser)
4 Control switch block (PS8700)
2-4
(J-2501-162-A)