Table of Contents
Advertisement
Quick Links
HMLCD19
19-inch LCD Monitor
User Manual
Video Systems
www.honeywellvideo.com
1-800-796-CCTV
© 2004 Honeywell International Inc.
All rights reserved. No part of this publication may be reproduced by any means
without written permission from Honeywell Video Systems. The information in
this publication is believed to be accurate in all respects. However, Honeywell
Video Systems cannot assume responsibility for any consequences resulting
from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to
incorporate such changes.
HMMU000882 – 04/04 – Rev. A
Advertisement
Table of Contents
Related Manuals for Honeywell HMLCD19
Summary of Contents for Honeywell HMLCD19
-
Page 1: User Manual
All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. -
Page 2: Specifications
ISSUE DATE April 2004 Initial Release (PCN 1632) Rev. A REVISIONS HMMU000882 04/09/04 SECTION 5: SPECIFICATIONS Type TFT Color Screen Size ” (diagonal) PC Input Signal RGB Analog Type 15-Pin D-Sub Sync H-Freq 31.5 80KHz V-Freq 75Hz Display Color 16,777,216 (24 bit) Resolution 1280 x 1024 @ 75Hz Video Band Width... -
Page 3: Limited Warranty
Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return product transportation prepaid, to Honeywell Video Systems Factory Service, 1305 Waters Ridge Drive, Lewisville, TX 75057. - Page 4 EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the...
- Page 5 GETTING OPTIMAL PICTURE Step 1: Window’s background or “H” character should be displayed on your screen. Step 2: Adjust the screen to the center of the Display (LCD) by using the top and bottom display controls and the V-Position Adjust menu.
- Page 6 SAFEGUARDS, CONTINUED ENVIRONMENT/INSTALLATION WARNINGS Do not place candlelight, mosquito coils, or cigarettes on top of the monitor or install it close to heating appliances. Doing so may damage the product or create a fire danger. The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
- Page 7 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED OSD Menu Description Horizontal position Select OSD MENU horizontal position. Vertical position Select OSD MENU vertical position. Timeout Time after which OSD MENU leaves screen. Transparency Adjust the transparency of the OSD Menu. English Language French German...
- Page 8 PURCHASE INFORMATION Date Purchased: Serial Number: Location Installed: Rev. A viii ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED OSD Menu Description The following table describes the OSD menu and a description of each option. OSD Menu Picture Auto adjustment Horizontal position Vertical position Horizontal size Phase...
- Page 9 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE Image and sound can easily be adjusted through an OSD menu. AUTO / EXIT Used to exit OSD. MENU / SEL Used to start the OSD and select options. Menu move/adjust buttons. Used to move the menu bar or adjust values.
-
Page 10: Timing Charts
TABLE OF CONTENTS, CONTINUED SECTION 4: TROUBLESHOOTING AND MAINTENANCE... 19 TROUBLESHOOTING ... 19 No Power... 19 Poor Picture Quality... 19 MAINTENANCE... 19 SERVICE AND SUPPORT ... 19 LIMITED WARRANTY ... 20 SECTION 5: SPECIFICATIONS... 21 Rev. A PRESET MODE CHART, CONTINUED Timing Charts Horizontal Frequency... - Page 11 SECTION 1: INTRODUCTION INTRODUCTION Honeywell's HMLCD19 SXGA Color LCD Display features a 19" viewable active matrix LCD screen, with outstanding 1280 x 1024 pixel resolution. When used in PC based applications the HMLCD19 provides connection points for VGA, PC Sound, and Headphones.
- Page 12 Some computer systems are not compatible with the DDC standard. If your monitor is displaying the wrong resolution, check your computer system for a DDC compatible video card and contact the Service Center. Do not open the monitor. There are no user- serviceable components inside.
- Page 13 NOTES: Rev. A CONTENTS OF PACKAGE LCD Monitor Sound Cable Power Cord Composite Cable OPTIONAL ACCESSORIES: S-video cable, Wall Mount HMMU000882 Rev. A 04/09/04 User Manual VGA Cable AC/DC Adapter Installation Disk Video Sound Cable BNC to RCA Adapters (2) adapter (VESA standard) HMMU000882 04/09/04...
- Page 14 NOTES: Rev. A DISPLAY MODES MEMORY The microcontroller has memory capacity to store 27 different display modes including timing formats and display settings. This memory capacity is divided into two parts: user setting area and factory presetting area. User Setting Area The user can add non-standard modes.
- Page 15 MICROCONTROLLER FEATURES The microcontroller automatically detects the video board installed in your system. When the monitor is turned on, the microcontroller first checks the display mode memory stored in the user setting area and the factory presetting area. Rev. A CONTROLS AND CONNECTIONS CONTROLS –...
- Page 16 CONTROLS – REAR PANEL DC12V PC Sound Video Sound S-VHS Composite Rev. A DVR or VCR HMMU000882 04/09/04 INSTALLING THE MONITOR DRIVER You can achieve an optimal resolution and scanning rate by installing the monitor driver as follows: 1. Insert the monitor driver diskette into the floppy diskette drive and run INSTALL.EXE.