Maytag PD Installation And Setup

STEP 1
PREPARE WASHER
To prevent the possibility of electrical shock,
1. Remove tape on lid. this washer (as is the case with other electrical
Remove accessory
appliances) must be adequately grounded.
package from tub.
It is the responsibility of the installer to assure
2. Tip the washer back-
the washer is adequately grounded at the point
ward. Loosen front
of installation taking into consideration the local
leveling leg lock nuts.
conditions and requirements. ALL GROUND-
ING MUST BE DONE IN ACCORDANCE
3. Tip washer slightly for-
WITH NATIONAL AND LOCAL CODES.
ward. Loosen rear leg
lock nuts. 5. Slide the washer into position. Do not
collapse or damage the drain hose.
4. REMOVE THE TUB
BLOCK.
6. Level the washer by turning the leveling legs in
or out as necessary. When the washer is level,
tighten the leveling lock nuts.
STEP 2
Lock Nuts
INSTALL WASHER
1. Insert the rubber hose washer from accessory
package into one end of the inlet hose. Attach
the inlet hoses to the HOT and COLD connec-
tions of the water valve on the back of the
washer. HOT and COLD connections are iden-
tified by H & C stamped on the bracket, HOT
on top, COLD on bottom. Be sure the hose
marked "HOT" is
attached to the HOT
connection. When
connecting the inlet SIPHON BREAK
hoses, be sure the
INSTALLATION
hose connections are
not cross-threaded on
If a 36" minimum standpipe is not available, or for
the water valve.
floor drain installation and in cases where a tight
Tighten by hand until
connection is made between the drain hose and
snug and then 2/3rds
drain (standpipe, etc.) the 12001586 siphon break
of a turn with pliers.
accessory is required.
Do not over-tighten as
this will strip threads on the water valve.
To install siphon break:
2. Insert both a rubber hose washer and a screen
1. Cut the corrugated drain hose at the center of
into the hoses for the faucet connections. The
the larger straight section position B.
dome on the screen strainer must point towards
the faucet. Attach the
inlet hoses to the HOT
and COLD faucets,
being sure the hose
marked "HOT" is
attached to the HOT
water faucet. NOTE:
Accessory inlet hoses
are available in various
2. Position a hose clamp onto the cut end of the
lengths up to 10 feet.
drain hose leading to the machine pump. Place
the mounting clamp onto the other cut end of
3. Place the drain hose in the
the drain hose.
Hose
drain facility. To change
Retainer
3. Place the rubber adapters inside the cut ends
drain hose direction or pre-
of the drain hose.
vent collapsing, turn the
short end of the hose while
4. Position the siphon assembly into the rubber
holding the base of the
adapters and tighten the hose clamp. (The
hose stationary.
closed end of the siphon break must point up.)
NOTE: If you must make
an airtight seal, use a floor
Mounting
drain, or if the standpipe is
HOSE
not at least 36", a siphon
RETAINER
break kit must be used
(see Siphon Break installa-
tion). The drain hose
Siphon
should be tied down with
Break
the cable tie provided.
H
5. Mount the siphon assembly and drain hose to
the cabinet with a screw through the mounting
clamp. Attach to the hole provided at the upper
left rear panel of the cabinet.
Siphon
Break
4. Plug the power cord into a grounded 120 volt,
60 Hz approved electrical service protected by
a 15 amp fuse or comparable circuit breaker.
This washer is grounded through the third
prong of the power cord when plugged into a
three prong grounded receptacle.
6. Place the drain hose into the drain facility. If
the drain hose will not reach, the 1200158 drain
hose extension kit is required.
COMMERCIAL TOP LOAD WASHER
LEAVE THESE INSTRUCTIONS WITH THE OWNER
PARTS supplied for installation:
Cable tie to secure drain hose to stand-
pipe, inlet hose or laundry tub
Beaded tie to secure drain hose to
cabinet (if required)
COLD WEATHER STORAGE
The following precautions should be taken if a washer is to be stored, after use, where it would be subject
to freezing conditions.
1. Turn off the water supply, and remove the inlet hoses.
2. Select a fill cycle and energize the water valve by selecting a warm water setting.
A few seconds of fill is sufficient.
3. Disconnect from electrical supply.
Clamp
4. Lower the drain hose to floor level and tilt washer backwards to remove water from the drain hose and
pump.
Drain Hose
PS MODELS ONLY
PS models are designed for
use with a coin slide of your
choice.
Rubber
SPECIAL NOTE: Some coin
Adapters
slides may require breaking
Hose Clamp
and removing the tab on the
actuator bracket.
Drain Hose
STEP 3
OPERATING WASHER
1. Insert coins until "SELECT CYCLE" flashes in display.
PD and PS Models: Minutes purchased are also shown on the display.
PR Models: A debit card is required rather than coins. In Enhanced Debit the card balance will also
Siphon Break
Mounting Hole
display when a debit card is inserted into the reader.
in Cabinet
2. Press fabric setting key pad for the wash cycle desired. After the cycle is started, the time will display
and count down.
GENERAL USER INFORMATION
Drain
Hose BLANK DISPLAY – This condition indicates the appliance is inoperative. Enter set-up mode to view
diagnostic code.
"0 MINUTES" SHOWING IN DISPLAY – This condition indicates the appliance cannot be operated. Coins
dropped or debit inputs during this condition will be stored in escrow but cannot be used until normal
operation is restored by opening and closing the lid. If the lid switch fails, it must be replaced before
normal operation can be restored.
COLD START (initial first use) – Appliance is programmed at the factory as follows:
Washer 10
1 rinse and 1 minute of rinse agitation (2 minutes rinse agitation for ENERGY STAR models)
$1.75 wash price (PD/PS models)
$0.00 wash price (PR models)WARM START (after power failure) – After a delay of up to 8 sec-
onds, the appliance is restored to the state that existed at time of the power failure.
INSTALLATION & SET-UP
PD / PS & PR MODELS
4 washers and 2 screens for water hoses
MAYTAG COMPANY, NEWTON, IOWA 50208
minute wash period (11 minutes for ENERGY STAR models)
PRICING – After the lid is opened following the completion of a
cycle, the display indicates the cycle price (unless set for free
operation). As coins are dropped or debit inputs arrive, the
display will change to lead the user through the initiation of a
cycle.
FREE CYCLES – This is established by setting the cycle price to
zero. When this happens "SELECT CYCLE" will appear
rather than a cycle price.
DEBIT CARD READY – This appliance is debit card "cable"
ready. It will accept a variety of debit card systems; but does
NOT come with a debit card reader. Refer to the debit card
reader manufacturer for proper machine set-up. In models
converted to a Generation 1 debit card system, debit pulses
represent the equivalent of one coin.
DISPLAY – After the unit has been installed and plugged in, the
display will show "0 MINUTES". Once the unit has been
plugged in and the washer lid opened the display will show
the price. In washers set for free cycles the display will flash
"SELECT CYCLE".
CONTROL SET-UP PROCEDURES
IMPORTANT: READ ALL INSTRUCTIONS BEFORE OPERATING!
The lower fabric setting key pads and the digital display are used to set up the controls. The display can
contain 4 numbers and/or letters and a decimal point. These are used to indicate the set-up codes and
related code values available for use in programming the appliance.
HOW TO USE THE KEY PADS TO PROGRAM THE CONTROLS
1. The LOWER LEFT key pad is used to adjust the values associated with set-up codes. Pressing the key
pad will increment the value. Rapid adjustment is possible by holding the key pad down.
2. The LOWER MIDDLE key pad will advance you through the set-up codes. Pressing the key pad will
advance you to the next available set-up code. Holding the key pad down will automatically advance
through the set-up codes at a rate of one (1) per second.
3. The LOWER RIGHT key pad is used to select or deselect options.
START OPERATING SET-UP
PD/PS Models: Insert access door key, turn, and lift to remove access door.
PR Models: Once the debit card reader is installed (according to the reader manufacturer's instructions),
the set-up mode can be entered by inserting a manual set-up card (supplied by the reader manufacturer)
into the card slot. If a manual set-up card is not available, manual set-up mode can be entered by removing
connector AA1 on the circuit board.
CAUTION: The console must not be opened unless power is first removed from the washer. To
2202533
access connector AA1, remove power, open console, disconnect plug on AA1, close console, apply power
to washer. The washer is now in the set-up mode.
Before proceeding, it is worth noting that, despite all of the options available, an owner can simply choose
to uncrate a new commercial machine, hook it up, plug it in and have a unit which operates.
The LOWER MIDDLE key pad will advance you from code to code. The LOWER LEFT key pad will
change the code value. The LOWER RIGHT key pad will select or deselect options.
FOR PS & PR MODELS: The set-up codes are the same as for the "PD" models except where noted.
The set-up code is indicated by the one or two left hand characters. The set-up code value is indicated by
the two or three right hand characters.
CODE EXPLANATION
607 6 REGULAR CYCLE PRICE
07 Represents the number of quarters (coin 1); may adjust from 0–39.
Tab
(See VALUE OF COIN 1.)
Advance from 0–39 by pressing the LOWER LEFT key pad.
Presently set for 7 quarters = $1.75
PR MODELS ONLY: Presently set for 0 quarters.
PS MODELS ONLY: Represents the number of push-in actuations of the coin slide
to start the machine. 601 setting would represent one coin slide actuation.
Press the LOWER MIDDLE key pad once to advance to next code.
710 7 WASH LENGTH
10 This is the number of minutes for WASH. Choose from 8 –20 minutes by pressing
the LOWER LEFT key pad.
Press the LOWER MIDDLE key pad once to advance to next code.
811 8 RINSE CYCLES
11 This is the length and total number of rinses.
Each rinse agitation is 1–4 minutes, with a choice of 1 or 2 rinses.
The middle digit is the length of rinse agitation and the right digit is the number of
rinses.
The number is changed in the following sequence (11, 21, 31, 41, 12, 22, 32, 42)
by pressing the LOWER LEFT key pad.
Press the LOWER MIDDLE key pad once to advance to next code.
The WOOLENS (if available) and DELICATES & KNITS cycles have a fixed rinse
agitation length of one minute.
900 9 CYCLE COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
00 Not Selected 'OFF'.
0C Selected 'ON' and not able to be deselected. Press the LOWER RIGHT key pad 3
consecutive times to select 'ON'. Once selected 'ON' it cannot be deselected.
Press the LOWER MIDDLE key pad once to advance to next code.
BRIGHT
WHITES COLORS COLORS
FABRIC SETTINGS
PERMANENT WOOLENS DELICATES
PRESS AND KNITS
BRIGHT
WHITES COLORS COLORS
FABRIC SETTINGS
PERMANENT WOOLENS DELICATES
PRESS AND KNITS
ENERGY STAR MODELS
BRIGHT
WHITES COLORS COLORS
FABRIC SETTINGS
PERMANENT DELICATES * SMALL
PRESS AND KNITS LOAD
SET-UP CODES