Roland AT-90SL Manual page 14

40 01 30 00 00 01 00-07
40 01 31 00 00 01 00-07
40 01 32 00 00 01 00-07
40 01 33 00 00 01 00-7F
40 01 34 00 00 01 00-7F
40 01 35 00 00 01 00-7F
REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set to the most
suitable value.
REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
40 01 38 00 00 01 00-07
40 01 39 00 00 01 00-07
40 01 3A 00 00 01 00-7F
40 01 3B 00 00 01 00-7F
40 01 3C 00 00 01 00-7F
40 01 3D 00 00 01 00-7F
40 01 3E 00 00 01 00-7F
40 01 3F 00 00 01 00-7F
CHORUS MACRO is a macro parameter that allows global setting of chorus parameters. When you use CHORUS MACRO to select the chorus type, each chorus parameter will be set to the most
suitable value.
●Part Parameters [GS Part: Model ID = 42H]
AT-90SL/80SL has 16 parts. Parameters that can be set individually for each Part are called Part parameters.
If you use exclusive messages to set Part parameters, specify the address by Block number rather than Part Number (normally the same number as the MIDI channel). The Block number can be
specified as one of 16 blocks, from 0 (H) to F (H).
The relation between Part number and Block number is as follows.
x...BLOCK NUMBER (0-F),Part 1 (MIDI ch = 1) x = 1
Part 2 (MIDI ch = 2) x = 2
: : :
Part 9 (MIDI ch = 9) x = 9
Part10 (MIDI ch = 10) x = 0
Part11 (MIDI ch = 11) x = A
Part12 (MIDI ch = 12) x = B
: : :
Part16 (MIDI ch = 16) x = F
In the following map, the Control Change controller number is expressed by the CC#.
Address (H) Size (H) Data (H)
40 1x 00 00 00 02 00-7F
40 1x 01# 00-7F
40 1x 02 00 00 01 00-10
40 1x 03 00 00 01 00-01
40 1x 04 00 00 01 00-01
40 1x 05 00 00 01 00-01
40 1x 06 00 00 01 00-01
40 1x 07 00 00 01 00-01
40 1x 08 00 00 01 00-01
40 1x 09 00 00 01 00-01
40 1x 0A 00 00 01 00-01
Rx. NRPN is set to OFF by power-on or by receiving "Turn General MIDI System On," and it will be set ON when "GS RESET" is received.
40 1x 0B 00 00 01 00-01
40 1x 0C 00 00 01 00-01
40 1x 0D 00 00 01 00-01
40 1x 0E 00 00 01 00-01
40 1x 0F 00 00 01 00-01
40 1x 10 00 00 01 00-01
40 1x 11 00 00 01 00-01
40 1x 12 00 00 01 00-01
REVERB MACRO
REVERB CHARACTER
REVERB PRE-LPF
REVERB LEVEL
REVERB TIME
REVERB DELAY FEEDBACK
CHORUS MACRO
CHORUS PRE-LPF
CHORUS LEVEL
CHORUS FEEDBACK
CHORUS DELAY
CHORUS RATE
CHORUS DEPTH
CHORUS SEND LEVEL TO REVERB
Parameter
TONE NUMBER
Rx. CHANNEL
Rx. PITCH BEND
Rx. CH PRESSURE (CAf)
Rx. PROGRAM CHANGE
Rx. CONTROL CHANGE
Rx. POLY PRESSURE (PAf)
Rx. NOTE MESSAGE
Rx. RPN
Rx. NRPN
Rx. MODULATION
Rx. VOLUME
Rx. PANPOT
Rx. EXPRESSION
Rx. HOLD1
Rx. PORTAMENTO
Rx. SOSTENUTO
Rx. SOFT
00: Room 1 04
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
0-7 04
0-7 00
0-127 40
0-127 40
0-127 00
00: Chorus 1 02
01: Chorus 2
02: Chorus 3
03: Chorus 4
04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay (FB)
0-7 00
0-127 40
0-127 08
0-127 50
0-127 03
0-127 13
0-127 00
Description Default Value (H)
CC#00 VALUE 0-127 00
P.C. VALUE 1-128 00
1-16, OFF Same as the Part Number
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 00 (01*)
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
OFF/ON 01
Hall 2
4
0
64
64
0
Chorus 3
0
64
8
80
3
19
0
Description
0
1
ON
ON
ON
ON
ON
ON
ON
OFF (ON*)
ON
ON
ON
ON
ON
ON
ON
ON
14