NAVMAN NZ LIMITED DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW. This manual represents the FUEL 3100 as at the time of printing. Navman NZ Limited reserves the right to make changes to specifications without notice.
4-6 Alarms setup (ALArm) ....................14 4-7 Units setup (UnItS) ....................14 5 Installation ..................... 15 5-1 What comes with the FUEL 3100? ................15 5-2 Tank / Engine Configurations ..................16 5-3 Installing the display unit .................... 16 5-4 Installing the Fuel Flow Transducer ................17 5-5 Power and Wiring ......................
Note that it is essential to update the fuel readings in the FUEL 3100 after a partial or full refill, or after manually removing fuel, to maintain accurate electronic readouts. The FUEL 3100 can also be customized with the Setup menus to suit your boat and preferences.
2 Operation 2-1 Turn on and off 2-5 Battery alarm Turn the FUEL 3100 on and off with the boat engine’s The FUEL 3100 can be set to sound an alarm when ignition switch. The FUEL 3100 does not have its the battery voltage is below the set alarm level.
U n I t S dAmP.S (1 CAL.F (0 or 9999) GrouP (0 (nAUt mILES, CAL.S ( 0.0 to 9999) dAmP.F (1 to 5) StAt mILES) to change a setting, ENT to confirm, then ESC for Setup Menu FUEL 3100 Installation and Operation Manual...
3 Fuel setup. conditions. Always carry adequate fuel for the See section 4-7 Units setup, for more information journey, plus a reserve. about customizing the FUEL 3100 to suit your boat and preferences. FUEL 3100 Installation and Operation Manual...
PORT and STBD. Press In addition, the fuel gauge splits into two columns; ENT again to make changes. the left column shows the fuel level in the port fuel tank and the right column shows the fuel FUEL 3100 Installation and Operation Manual...
4 The Setup Menus Use the setup menus to customize the FUEL 3100 It is essential to update this setting whenever any to suit your boat and preferences. fuel is added or removed. Otherwise, all the fuel readings and the Low Fuel Alarm become 4-1 Entering setup mode meaningless.
Page 10
4 gallons (15 litres), has been used per engine. 5. The USED readout shows the apparent amount of fuel used. 6. Select the FUEL setup menu, then press FUEL 3100 Installation and Operation Manual...
GPS (speed over ground) Speed of river Speed displayed Trip log Economy Range Paddlewheel (speed over water) 15 knots 30 nm 5.0 nm/gal 250 nm GPS (speed over ground) 10 knots 20 nm 3.3 nm/gal 165 nm FUEL 3100 Installation and Operation Manual...
Page 12
FUEL 3100. (SEn must have been through the water. A speed reading from a GPS is selected as the source of the speed input.) the speed over the ground.
For example, selecting StAT mILES automatically sets the speed unit to mPH. The FUEL 3100 is set up with US Gallons, knots, and nautical miles as the default. 2. Enter the fuel level that will trigger the alarm and press ENT to confirm.
FUEL 3100 speed transducer options instructions supplied with the transducer, or consult Available in the following ready-to-install kits: your NAVMAN dealer. 5-1 What comes with the FUEL 3100? Standard configuration FUEL 3100 display unit Protective cover Fuel flow transducer and cable 8 m (26¼ ft)
5-2 Tank / Engine Configurations 5-3 Installing the display unit The FUEL 3100 can be used with the following fuel Warnings tank / engine configurations: 1. The display unit is waterproof from the front. Twin fuel tanks / twin fuel lines / twin engines / Protect the rear from water, otherwise water might twin fuel transducers (below).
However, changing the backlight setting Wiring a single unit in an instrument in group 0 will not affect Wire the FUEL 3100 as shown below if it will be instruments in different groups. Black if an alarm sounds, mute it by clearing the alarm on any instrument which can display that alarm.
All settings may be reset to the manufacturer’s default settings (see below). Power on the boat (and any instruments) to check that the FUEL 3100 is working. To reset to factory defaults: See section 4-3 Fuel setup, to select: Turn the power off.
1 (6 seconds) 2 (12 sconds) 3 (18 seconds) 4 (24 seconds) 5 (30 seconds) Calibration Fuel can be calibrated. Speed can also be calibrated if the optional speed transducer is installed. FUEL 3100 Installation and Operation Manual...
Repairs to the unit must only be carried rear of the unit. Air the boat or run the out by a service centre approved by Navman NZ FUEL 3100 with backlight fully on. Limited. Users who service the unit themselves will Water has entered the breathing tube.