Related Manuals for Phonic WM-SYS3
Summary of Contents for Phonic WM-SYS3
- Page 1 WM-SYS3/WM-SYS3D/WM-SYS4/WM-SYS4D Wireless Kit For Active Speakers WM60 WIRELESS T RANSMITTER SIG/CLIP User’s Manual ENGLISH WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
-
Page 2: Important Safety Instructions
WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 3: Table Of Contents
CONNECTING THE WM400(D) TO A SPEAKER ............3 SPECIFICATIONS ....................4 EQ PRESETS ......................5 Phonic reserves the right to improve or alter any information suppied within this document without prior notice. V. AUG 6, 006 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 4: Introduction
AF, RF and x WM70 dual channel transmitter x WM400(D)-L left channel receiver delay bypass indicators x WM400(D)-R right channel receiver 3x power supplies for WM70, WM400(D)-L and WM400(D)-R M6, M8, M0 screws Velcro strip WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 5: Quick Setup
Turn the WM60 on first, then the WM400(D). Provided you have a signal going out of your mixer, and your Speaker is turned on, the wireless transmission should be working. WM400 WM60 WIRELESS T RANSMITTER SIG/CLIP WM60 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 6: Dual Channel Setup
Adjust the channel on the WM70 and both WM400(D)’s so they are identi- cal. If you wish to send and receive a signal successfully, this is of utmost importance! WM400 WM400 WM70 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 7: Troubleshooting
Performer speakers is turned up. Weak signal? ● Try maintaining a better line-of-site connection between the transmitter and receiver. ● Change both transmitter and receiv- er to a new frequency. WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 8: Wm60 Transmitter
(change the position if the wireless signal quality is poor). Push the an- tenna in to release it before adjusting its position. WM60 WIRELESS T RANSMITTER SIG/CLIP DC IN INPUT WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 9: Wm70 Transmitter
WM70 to be al- ternated between a mono and stereo signal. On/Off Button – this button turns the WM70 on and off. An LED will il- luminate under this button when it is WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 10: Wm400 Receivers
H 0 (kHz) – H 60 (Hz) the digital processing feature of the (High and low cut filters are adjusted in 1 Hz incre- WM400D receiver is off. ments; 10Hz increments above 1kHz) WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... - Page 11 M6, M8 or M0 (change the position if the wireless screws. signal quality is poor). Push the an- tenna in to release it before adjusting its position. WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
-
Page 12: The Wm400D's Digital Features
There are 30 pre- sets to choose from (check EQ Preset page for more information), the titles of which describe what the effect does to your audio. The default setting, P0, is completely flat. WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 13: Connecting The Wm400(D) To A Speaker
Users can connect the WM400(D) Receiver modules to an active speaker using a mounting point or the included velcro strips, as indicated. Mounting Point Velcro Strip Velcro-Hooks Velcro-Hooks Velcro-Hooks Velcro-Loops Velcro-Loops Velcro-Hooks Velcro-Hooks WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 14: Specifications
LED Indicators : Power On/Off, Sig/Clip Power : External Adaptor, VDC Output Power : <50 mW Dimensions : 40 x 43.5 x 79 mm (5.5” x .7” x 7”) Net Weight : 35 g (0.7 lbs) WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... -
Page 15: Eq Presets
EQ PRESETS WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D... - Page 16 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 17 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 18 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 19 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 20 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 21 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 22 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 23 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 24 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
- Page 25 WM-SYS3 / WM-SYS3D / WM-SYS4 / WM-SYS4D...
Need help?
Do you have a question about the WM-SYS3 and is the answer not in the manual?
Questions and answers