Page 2
ELECTRIC UNIT (X34- ) DME1 PRE OUT SERVO Q367,368,401,402,411,412 (FRONT) J400 PRE OUT D3.3V MUTE (REAR) IC480 PRE OUT 4VPRE+B (SW) IC500 IC700 POWER IC720 SP OUT(FL) FM/AM SP OUT(FR) E-VOL D1.8V SP OUT(RL) OFFSET AUX (FRONT) SP OUT(RR) BU5V IC680,682 WH190 WIRED...
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY BLOCK DIAGRAM MOTHER CD PLAYER UNIT (X32-6130-00) BOARD (X34- ) DPU1 SRAMSTB SRAMSTB SIGNAL A,B,C,E,F BUCK BUCK PIO0 PIO0 MRST MRST RF AMP BSIF ST REQ BSIF ST REQ VREF SERVO BSIF GATE BSIF GATE PROCESSOR BSIF DATA...
Page 4
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY COMPONENTS DESCRIPTION Ref. No. Application / Function Operation / Condition / Compatibility IC680,682 Level Shift Converts 3.3V to 5V. Decodes MP3 or other fi les of audio/decompression standards by software based IC700 SOC (System On Chip) architecture. IC750 iPod Authentication Coprocessor For iPod authentication.
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY MICROCOMPUTER’S TERMINAL DESCRIPTION ● SYSTEM μ-COM: IC600 on X34- (ELECTRIC UNIT) Truth Value Pin No. Pin Name Application Processing / Operation / Description Table External display remote control input REMO Panel remote control input LX REQ M Communication request to slave unit Not used Output L fi...
Page 6
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Value Pin No. Pin Name Application Processing / Operation / Description Table Detects Pulse ROTARY CW VOL key detection 15-pulse/360°, 2-pulse/1-click CD MUTE CD mute request L: Mute request (Bolero), H: Normal condition VFD CE...
Page 7
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Value Pin No. Pin Name Application Processing / Operation / Description Table 83,84 Not used Output L fi xed MUTE 0 E-VOL front mute L: ON, H: OFF MUTE 1 E-VOL rear mute L: ON, H: OFF...
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE ■ Example ÷ ÷ ÷ ÷ ÷ ÷ ÷ Description of display Description Disc EJECT times display. MAX 65535 (times) Disc EJECT times While disc EJECT times is displayed, press and hold for 2 display ■5 seconds or longer to clear disc EJECT times.
Page 9
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE ■ Special displays when all lights are on in STANDBY source Description of display Description Common All lights ON. All lights ON. ÷ ÷ ÷ ÷ ÷ ÷ ÷ Destination terminal “TYPE” indicates system μ-com (IC1) destination, and...
Page 10
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE • CD information display mode Description of display Description Mechanism error log 1 (Latest) XX: Error number. “– –” is displayed in case there is no error. CD mecha- Mechanism error log 2 (Latest) nism error XX: Error number.
Page 11
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE ■ Test mode specifi cations in TUNER source Error is found in front-end (A1), etc. if indications below is displayed while in tuner source. Status Display Description Front-end (A1) E2PROM is still the default Front-end (A1) E2PROM data error (unspecifi...
Page 12
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE Description of display Description Displays the data that has been written in the Adjustment value E2PROM when pressing the key for 2 seconds or ■ memory longer. Clear the FST adjustment mode. (Returns to Mode clear 8 .
Page 13
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE ■ Audio-related test mode Procedure Note Enter audio adjustment mode (the initial item should be Fader, and then, Balance → Press the [AUD] key (main unit) Bass Level → Middle Level → Treble Level → SW Level → System Q → HPF Front →...
Page 14
This mode is cancelled by resetting. (The last screen will not be retained.) ■ FM/AM channel space switching (KDC-MPxxxx and KDC-X492 only) Procedure Note While Power OFF, press and hold [1] key and [5] key, FM200kHz/AM10kHz ↔ FM50kHz/AM9kHz and press [SRC] key to Power ON FM50kHz/AM10kHz ↔ FM200kHz/AM10kHz (KDC-MP408U)
Page 15
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE ■ Security • Forced Power ON mode Procedure Note While “– – – –” is displayed, power can be turned ON for only 30 While pressing and holding [M.JOG] key and [4] key, reset-start. minutes. After 30 minutes, can only be recovered by resetting.
Page 16
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY TEST MODE ■ ROM data transfer When replacing front-end (A1), this function is used to transfer E2PROM data (ROM correction, security and other data) to front-end (A1) to E2PROM of to mother unit (X34-), used for saving data, and, after completing replacement of front-end (A1), to recover data from the E2PROM of the mother unit (X34-), and for saving data to the new front-end (A1).
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY ROM DATA TRANSFER PROCESSES ■ Operation procedure When replacing front-end (A1) of mother unit (X34-), or when adding or replacing ROM correction (program correction Operation procedure is different depending on the condi- with ROM IC (IC10)), the following activities are required.
Page 18
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY ROM DATA TRANSFER PROCESSES Turn power on. Install new front-end (A1). Press and hold the [1] and [3] keys and press reset button. No ROM correction or other data status. (Enter the system in the test mode.) Press [B.BOOST] key. (ROM data System enters data trans- fer mode.)
Page 19
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY ROM DATA TRANSFER PROCESSES 4. In case of applying a new ROM correction when front- Turn power on. end (A1) is replaced (There is ROM correction data.) Press and hold the [1] and [3] keys, press reset button. (Enter 5.
Page 20
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY ROM DATA TRANSFER PROCESSES Press key. (Exit ROM data transfer mode.) Turn power on. Turn power off. Press and hold the [1] and [3] keys press reset button. (Enter the system in the test mode.) Remove front-end (A1).
Page 21
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY PC BOARD PC BOARD (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) SWITCH UNIT SWITCH UNIT X16-622x-xx (J76-0477-12) X16-622x-xx (J76-0477-12) R120 C104 D107 /C107 CP11 USB-GND ILL+B USB-D+ PAN-5V AUX-GND GUARD USB-D- CP14 USB 5V R112 AUX-L AUX-R R101 VFD-RST...
Page 25
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY X34-577x-xx Ref. No. Address Q140 Q141 Q142 Q150 D442 D440 Q320 Q400 Q410 Q704 Q705 D320 W321 Q320 C494 C493 C492 R516 R643 R603 R642 R645 C603 R624 R648 R608 R609 R619 R618 C604 R615 R634 R667 R668 R669 Refer to the schematic diagram for the values of resistors and capacitors.
Page 26
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY PC BOARD (COMPONENT SIDE VIEW) CD PLAYER UNIT X32-6130-00 (J76-0495-12) R261 R216 C104 R281 X32-6130-00 Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 27
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY PC BOARD (FOIL SIDE VIEW) SGND S7.5V CD PLAYER UNIT LO/EJ DRVMUTE MOTOR X32-6130-00 (J76-0495-12) SPDL+ R288 LOE-SW 8-SW SRAM MRST PIO0 AMUTE SLD- SLD+ LOAD A.GND EJECT SPDL- BUCK R240 R289 BU1.5V C101 R241 R246 R231 D1.5V...
Page 28
KDC-MP408U/MP438U/X492/MP5039U/MP5539U/W5041UA/ W5041UG/W5141UAY/W5141UGY/W5541U/W5641UY PRE OUT ELECTRIC UNIT (X34-5xxx-xx) ∗ J440 J400 TP502 ∗ IC500 POWER 5L I/F ∗ ∗ SUB(+REAR) FRONT REAR C402 C403 C412 C413 C422 C423 1000P 1000P 1000P 1000P 1000P 1000P R402 R403 R412 R413 R422 R423 D440...
FM tuner section Frequency range Auxiliary input 200kHz space ........87.9MHz~107.9MHz Frequency response (±1dB) ......20Hz~20kHz 50kHz space (KDC-MP408U) ..87.5MHz~108.0MHz Input Maximum Voltage ..........1200mV Usable sensitivity (S/N=30dB) ....9.3dBf (0.8μV/75Ω) Input Impedance ............10kΩ Quieting Sensitivity (S/N=50dB) ....15.2dBf (1.6μV/75Ω) Frequency response (±3.0dB) ......30Hz~15kHz General Signal to Noise ratio (MONO) ........70dB...
Page 48
LW tuner section Weight .................1.40kg Frequency range ......... 153kHz~281kHz Usable sensitivity (S/N=20dB) ........45μV KENWOOD follows a policy of continuous advancements in development. For this reason specifi cations may be changed without notice. DANGER: Please do not look at the laser beam directly during...