INSTALLATION INSTRUCTIONS
Models 2405.016 and 2408.016
Retrospect Two Piece Toilet
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
FINISHED WALL
2a
719mm
(28-5/16)
25mm 6mm
(1
1/4)
216mm (8-1/2")
C/L OF SEAT POST HOLES
140mm (5-1/2) CENTERS)
(17-1/2)
90mm
(3-9/16")
(13-9/16)
13mm
(1/2)
159mm
(6-1/4)
305mm
C/L OF OUTLET
(12)
2b
FINISHED WALL
25
6mm (1
1/4")
768mm
(30-1/4")
216mm
(8-1/2")
C/L OF SEAT POST
MTG HOLES ON
140mm (5-1/2") CTRS
494mm
(19-7/16")
13mm (1/2")
90mm
(3-9/16")
389mm (15-5/16")
168mm (6-5/8")
305mm
C/L OF OUTLET AND
(12")
TOILET MTG BOLTS
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 3
Adjustable Wrench
Flexible Supply Tube
444mm
406mm
(16)
SUPPLY AS
REQUIRED
381mm
(15)
*
222mm
(8-3/4)
344mm
*
152mm
(6)
FINISHED
FLOOR
2408.016 RETROSPECT RF
C/L OF SUPPLY
AS REQUIRED
*
203mm
(8")
2405.016 RETROSPECT EL
Sealant
Closet Bolts
486mm
(19-1/8)
C/L
794mm
(31-1/4)
279mm
(11)
486mm
(19-1/8")
C/L
400mm
838mm
(15-3/4")
(33")
425mm
(16-3/4")
FINISHED
FLOOR
273mm
(11-5/8")
*
152mm (6")
Tape Measure
Carpenters Level
3
CLOSET FLANGE
A
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ,
and slide into place 6" (152 mm) apart and
parallel to wall.
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly
around waste flange (horn), with
tapered end of ring facing toilet. Apply
a thin bead of sealant around toilet
base.
WAX RING
7 3 07 2 9- 1 00