Advertisement
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
FloWise™ DUAL FLUSH 2-PIECE TOILET
Normal Height, Elongated Rim: 2479 / 2476 / 2779
Right Height™ Elongated Rim: 2480 / 2484 / 2778 / 2566
Normal Height, Round Front: 2489
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line.
NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
MODELS:
2479
2476
2779
2480
2484
2778
2566
2489
3
CLOSET
FLANGE
A
CLOSET
BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90°, and slide into place 6"
(152mm) apart and parallel to wall.
TEMPORARILY set toilet in place.
Place tapered washer and nuts onto
the bolts as shown in Step 5. Mark bolt
length needed for bolt cap clearance.
Remove toilet. Precut the bolts to
length by twisting the nut onto the bolt
past the cut mark, then cutting the bolt
to the desired length with a hacksaw.
Unscrew the nut to repair the threads.
Re-install bolts in flange.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a I n c .
© A S A m e r i c a I n c . 2 0 0 9
Adjustable Wrench
Flexible Supply Tube
DIMENSION A:
12"
(305 mm)
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
Sealant
Closet Bolts
FINISHED WALL
A
FINISHED FLOOR
5
WAX RING
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP" must face up!
Certified by
IAPMO R&T
Tape Measure
Carpenters Level
C/L
SUPPLY
AS
REQUIRED
BOLT
CAP
NUT
TAPERED
WASHER
CLOSET
BOLT
FLANGE
7301144 -1 0 0 Re v. H
Advertisement
Related Manuals for American Standard 3067.216.020 - 3067.216.020 FloWise Dual Flush Elongated High Efficiency Toilet Bowl
Summary of Contents for American Standard 3067.216.020 - 3067.216.020 FloWise Dual Flush Elongated High Efficiency Toilet Bowl
- Page 1 Normal Height, Round Front: 2489 Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
-
Page 2: Install Toilet
Tank Installation Kit Includes: 2 bolts, 2 rubber washers, 4 metal washers, 4 metal nuts, 2 plastic nuts, 1 large rubber gasket. RUBBER WASHER RUBBER TANK MTG. GASKET BOLT CAP BOLTS WASHER CLOSET FLANGE WASHER CLOSET BOLT WASHER INSTALL TANK a. -
Page 3: Repair Parts List
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). - Page 4 TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 13. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: LIFT ARM FIRST • The flush valve is leaking because it's worn, dirty or misaligned with tank ball or flapper (replace with a new flapper).