Page 1 D-Link DFM-562IS HSFi PCI Modem User’s Guide User’s Guide...
Page 2: Radio Frequency Interference Statement
D-Link DFM-562IS HSFi PCI Modem User’s Guide FCC Requirements This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. IF REQUESTED. THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.
Page 3 D-Link DFM-562IS HSFi PCI Modem User’s Guide WARNING ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIONS COMPLIANCE LABEL WARNING FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIOS COMPLIANCE LABEL. THIS INCLUDES CUSTOMER EQUIPMENT PREVIOUSLY LABELLED PERMITTED OR CERTIFIED. Modems connected to the Australian telecommunications network must be marked in accordance with the Labeling Notice.
Page 4: Table Of Contents
D-Link DFM-562IS HSFi PCI Modem User’s Guide CONTENTS Chapter 1 Introduction............5 1.1 Introduction..................5 1.2 Packing....................5 1.3 Features .....................5 Chapter 2 Specifications............. 6 Chapter 3 Hardware Installation ........7 Chapter 4 Software Installation ........8 4.1 Windows 95..................8 4.2 Windows 98..................11 4.3 Windows ME...................19...
Page 5: Chapter 1 Introduction
Chapter 1 Introduction 1.1 Introduction Thank you for selecting the D-Link DFM-562IS HSFi PCI Modem . It provides the modem function under Windows GUI interface supplied by Windows. All of the above advances come from the special design of Windows control function, which move the dominating of control signal of modem from modem body to the Windows system.
Page 6: Chapter 2 Specifications
D-Link DFM-562IS HSFi PCI Modem User’s Guide Chapter 2 Specifications Specifications: Line data rate 56000,54000,52000,50000,48000,46000,44000,42000, 40000,38000,36000,34000,33600,31200,28800,26400, 24000,19200,16800,14400,12000,9600,7200,4800,2400 ,1200,600,300 Modem protocol ITU-T V.92,V.90/K56flex/ITU-T V.34bis/V.34/V.32bis/V.32/V.22bis/V.22/V.21/V.23 Bell 212A/103,V.80,V8/V.8bis Chip Set Conexant HSFi-CX11251-11 Interface PCI BUS Fax Compatibility 14.4k bps Send/Receiver G3 compatible Error Correction MNP2-4,V.42...
Page 7: Chapter 3 Hardware Installation
D-Link DFM-562IS HSFi PCI Modem User’s Guide Chapter 3 Hardware Installation 1. Remove the computer’s case. 2. Insert the modem card into a spare PCI expansion slot. 3. Close the case. 4. Unplug the telephone from the wall socket, then plug the telephone into the socket on the back of the modem marked PHONE.
Page 8: Chapter 4 Software Installation
D-Link DFM-562IS HSFi PCI Modem User’s Guide Chapter 4 Software Installation Power on your computer then start Windows 95/98//ME/NT4.0/2000/XP. Windows 95/98/ME/NT4.0/2000/XP will detect the modem automatically. 4.1 Windows 95 B (OSR2) When you see the message of PCI Communication Device shown on the screen.
Page 9 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click Other Locations… to search for the correct driver and location Select the location of F:\Win95 (F is the letter of your CD-ROM drive) and click...
Page 10 D-Link DFM-562IS HSFi PCI Modem User’s Guide Windows 95 will find the driver shown as below, then click Finish. Click OK. Type F: \WIN95 or use the Browse to find the location of the modem driver, then click OK.
Page 11: Windows 98
D-Link DFM-562IS HSFi PCI Modem User’s Guide 4.2 Windows 98 The message of PCI Commucication Device will appear. However it may vary with the type of your mother board Please insert the driver CD supplied and click Next. 2. Select Search for the best driver for your device [Recommended] and click...
Page 12 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Select Specify a location and type F:\Win98 (F is the letter of CD-ROM drive ) and click Next to continue. Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and click Next.
Page 13 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click Finish to end this installation procedure. 6. The message of D-Link DFM-562IS HSFi PCI Modem will appear. However it may vary with the type of your mother board Please insert the driver CD...
Page 14 D-Link DFM-562IS HSFi PCI Modem User’s Guide Select Search for the best driver for your device [Recommended] and click Next. Select Specify a location and type F:\Win98 (F is the letter of CD-ROM drive ) and click Next to continue.
Page 15 D-Link DFM-562IS HSFi PCI Modem User’s Guide Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and click Next. Click Finish to end this installation procedure.
Page 16 D-Link DFM-562IS HSFi PCI Modem User’s Guide The message of Wave Device for Voice Modem will appear. However it may vary with the type of your mother board Please insert the driver CD supplied and click Next. Select Search for the best driver for your device [Recommended] and click...
Page 17 D-Link DFM-562IS HSFi PCI Modem User’s Guide Select Specify a location and type F:\Win98 (F is the letter of CD-ROM drive ) and click Next to continue. Windows will find the driver for Voice Modem Serial Ware Device and click...
Page 18 D-Link DFM-562IS HSFi PCI Modem User’s Guide 15. Click Finish to end this installation procedure.
Page 19: Windows Me
D-Link DFM-562IS HSFi PCI Modem User’s Guide 4.3 Windows ME The message of PCI Commucication Device will appear. Select Specify the location of the driver [Advanced] and click Next. 2. Select Search for the best driver for your device. [Recommended], then Select Specify a location and type I:\WinME ( I is the letter of CD-ROM drive ) and click Next to continue.
Page 20 D-Link DFM-562IS HSFi PCI Modem User’s Guide Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and click Next. Click Finish to end this installation procedure.
Page 21 D-Link DFM-562IS HSFi PCI Modem User’s Guide The message of Modem Device will appear. Select Specify the location of the driver [Advanced] and click Next. 6. Select Search for the best driver for your device. [Recommended], then Select Specify a location and type I:\WinME (I is the letter of CD-ROM drive ) and...
Page 22 D-Link DFM-562IS HSFi PCI Modem User’s Guide Windows will find the driver for D-Link DFM-562IS HSFi PCI Modem and click Next. Click Finish to end this installation procedure.
Page 23: Windows Nt 4.0
D-Link DFM-562IS HSFi PCI Modem User’s Guide 4.4 Windows NT 4.0 1. Please insert the driver CD supplied. Then click Start \ Run on the desktop and use Browse to open the file of F:\WinNt4\Setup.exe (F is the letter of CD-ROM drive), then click OK.
Page 24 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Click Next. 4. The message of The modem driver was installed successfully and clicks Finish. Note: You must restart your computer to enable the modem driver.
Page 25 D-Link DFM-562IS HSFi PCI Modem User’s Guide If you want to use Dial-Up Networking, please do as following. After restarting your computer, click Start \ Settings \ Control Panel on the desktop and double-click on the Network icon. 6. Click on the Services tab and select Remote Access Service, then click Properties.
Page 26 D-Link DFM-562IS HSFi PCI Modem User’s Guide 7. Click on the Add button to add the D-Link DFM-562IS HSFi PCI Modem. If there is any other modem in the list, please click Remove first. 8. Select COM3-D-Link DFM-562IS HSFi PCI Modem, then click OK.
Page 27 D-Link DFM-562IS HSFi PCI Modem User’s Guide 10. Select Dial out only for Port Usage and click OK to confirm the settings. 11. Click Network to configure the network. 12. Select TCP/IP for Dial out Protocols and click OK to confirm the settings.
Page 28 D-Link DFM-562IS HSFi PCI Modem User’s Guide 13. Click Continue to complete the setup. 14. Click Close.
Page 29 D-Link DFM-562IS HSFi PCI Modem User’s Guide 15. Click Yes to restart your computer. 16. After restarting your computer, please double-click on the My Computer icon on the desktop and double-click on the Dial-Up Networking icon. 17. If your phonebook is empty, please click OK to add an entry.
Page 30 D-Link DFM-562IS HSFi PCI Modem User’s Guide 18. You may use the name provided or enter a different one, then click Next. 19. Select The non-Windows NT server I am calling… then click Next.
Page 31 D-Link DFM-562IS HSFi PCI Modem User’s Guide Enter the Phone number of your local ISP and click Next. Select Point-to-Point Protocol (PPP) and click Next.
Page 32 D-Link DFM-562IS HSFi PCI Modem User’s Guide 22. Select None under normal condition, or consult with your local ISP for other choice and click Next to continue. Enter your IP address if you have a fixed one or leave the value: 0.0.0.0, then click Next.
Page 33 D-Link DFM-562IS HSFi PCI Modem User’s Guide 24. Enter the IP addresses of a DNS and/or WINS server for your local ISP or set 0.0.0.0 if you are not sure. Then click Next to continue. 25. Click Finish to save the settings for the new phonebook entry.
Page 34 D-Link DFM-562IS HSFi PCI Modem User’s Guide 26. Click on the More buttons and select Edit entry and modem properties…. 27. Select D-Link DFM-562IS HSFi PCI Modem (COM3) from Dial using list and click on the Configure button.
Page 35 D-Link DFM-562IS HSFi PCI Modem User’s Guide 28. Enable all the Hardware Features and select 115200 from Initial speed list, then click OK. 29. Click on the Server tab and enable three options of TCP/IP, Enable software compression and Enable PPP LCP extensions.
Page 36 D-Link DFM-562IS HSFi PCI Modem User’s Guide 30. Click on the Security tab and enable the option: Accept any authentication including clear text, then click OK. 31. The phonebook entry has been edited, click Dial to connect to.
Page 37 D-Link DFM-562IS HSFi PCI Modem User’s Guide 32. Enter User name and Password and click OK, and the modem will dial out to your ISP and get a connection.
Page 38: Windows 2000
D-Link DFM-562IS HSFi PCI Modem User’s Guide 4.5 Windows 2000 1. Windows will detect the modem automatic; please insert the driver CD supplied and clicks Next to continue. 2. Select Search for a suitable driver for my device [recommended], and click...
Page 39 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Select Specify a location, then click Next to continue. 4. Please type G:\Win2K (G is the letter of your CD-ROM driver), then click OK to continue.
Page 40 D-Link DFM-562IS HSFi PCI Modem User’s Guide 5. Click Next to continues. 6. Click Yes.
Page 41 D-Link DFM-562IS HSFi PCI Modem User’s Guide 7. Click Finish to end procedure.
Page 42: Windows Xp
D-Link DFM-562IS HSFi PCI Modem User’s Guide 4.6 Windows XP . Select Install from a list specific location [Advanced], then click Next. Select Include this location in this search, then click Next .
Page 43 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click Continue Anyway. This installation has been done; click Finish to end this procedure.
Page 44: Chapter 5 Select Modem Country
Chapter 5 Select Modem Country 5.1 Windows 95 Move your courser as following sequence Start\Settings\Control Panel and click Control Panel. Then double-click on the System icon. Click Device Manager tab and select D-Link DFM-562IS HSFi PCI Modem, then click Properties.
Page 45 D-Link DFM-562IS HSFi PCI Modem User’s Guide Select country form the list , then click OK.
Page 46: Windows 98/Me
User’s Guide 5.2 Windows 98/ME Move your courser as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Modems icon. Select General and click D-Link DFM562IS HSFi PCI Modem, then click Dialing Properties.
Page 47 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. In the I am in this country/region, to select United States of America and click Apply. 4. Click OK.
Page 48 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click OK to end this procedure.
Page 49 D-Link DFM-562IS HSFi PCI Modem User’s Guide 5.3 Windows NT4.0 1. Move your courser as following sequence Start \ Settings \ Control Panel and click Control Panel and double-click on the HSF Modem Region Select icon. 2. Select your country form a list and click OK.
Page 50: Windows 2000
D-Link DFM-562IS HSFi PCI Modem User’s Guide 5.4 Windows 2000 Move your courser as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Phone and Modem Options icon. Select Dialing Rules and click My Location. Then click Edit….
Page 51 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click General and in the Country/region to select United States of America. Then click Apply. Click OK.
Page 52 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click OK to end this procedure.
Page 53: Windows Xp
D-Link DFM-562IS HSFi PCI Modem User’s Guide 5.5 Windows XP 1. Move your courser as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Phone and Modem Options icon. 2. Select Dialing Rules and click My Location. Then click Edit….
Page 54 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Click General and in the Country/region to select United States of America. Then click Apply. 4. Click OK.
Page 55 D-Link DFM-562IS HSFi PCI Modem User’s Guide 5. Click OK to end this procedure.
Page 56: Chapter 6 Diagnostics
D-Link DFM-562IS HSFi PCI Modem User’s Guide Chapter 6 Diagnostics 6.1 Windows 95/98/ME Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Modems icon. To test the modem by clicking on the Diagnostics tab. Select the COM port that...
Page 57 D-Link DFM-562IS HSFi PCI Modem User’s Guide Responding to AT commands and functioning correctly, it means that your modem is working properly. Click OK to end this procedure. Click OK.
Page 58: Windows 2000
1. Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Phone and Modem Options icon. 2. Click on the Modems, then select D-Link DFM-562IS HSFi PCI Modem and click Properties.
Page 59 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Click Diagnostics. To test the modem by clicking Query Modem. 4. If your modem is responding to AT commands and functioning correctly, it means that your modem is working properly. Click OK to end this procedure.
Page 60 D-Link DFM-562IS HSFi PCI Modem User’s Guide 5. Click OK to end this procedure.
Page 61: Windows Xp
D-Link DFM-562IS HSFi PCI Modem User’s Guide 6.3 Windows XP Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Phone and Modem Options icon. Select Modems and click FM-56PCI-HSFi-AB, then click Properties.
Page 62 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click Diagnostics. To test the modem by clicking Query Modem. If your modem is responding to AT commands and functioning correctly, it means that your modem is working properly. Click OK to end this procedure.
Page 63 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click OK to end this procedure..
Page 64: Chapter 7 Uninstalling Procedures
7.1 Windows 95 Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Add/Remove Programs icon. 2. Select D-Link DFM-562IS HSFi PCI Modem from the list and then click the Add/Remove button.
Page 65 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Click Yes to remove the modem then click OK.
Page 66: Windows 98/Me
7.2 Windows 98/ME Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Add/Remove Programs icon. 2. Select D-Link DFM-562IS HSFi PCI Modem from the list and then click the Add/Remove button.
Page 67 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click Yes to end this procedure and restart your computer.
Page 68: Windows Nt4.0
7.3 Windows NT 4.0 1. Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Add/Remove Programs icon. 2. Select D-Link DFM-562IS HSFi PCI Modem from the list and then click Add/Remove.
Page 69 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Click Next. 4. The message of The modem driver was un-installed successfully will appear, and click Finish.
Page 70: Windows 2000
D-Link DFM-562IS HSFi PCI Modem User’s Guide 7.4 Windows 2000 1. Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Add/Remove Programs icon. 2. Click D-Link DFM-562IS HSFi PCI Modem. Then click Chang/Remove.
Page 71 D-Link DFM-562IS HSFi PCI Modem User’s Guide 3. Click Close.
Page 72: Windows Xp
D-Link DFM-562IS HSFi PCI Modem User’s Guide 7.5 Windows XP Move your cursor as following sequence Start \ Settings \ Control Panel and click Control Panel. Then double-click on the Add or Remove Programs icon. Click D-Link DFM-562IS HSFi PCI Modem. Then click Chang/Remove.
Page 73 D-Link DFM-562IS HSFi PCI Modem User’s Guide Click Close.