°"√µ' ¥ µ— È ß
2.
INSTALLATION
1)
®–µ' ¥ µ— È ß ‡§√◊ Ë Õ ß∑' Ë ‰ Àπ
Where to install
❑
®–µâ Õ ßµ' ¥ µ— È ß ‡§√◊ Ë Õ ß‡¢â " °— ∫ ºπ— ß µ"¡√Ÿ ª
❑
§«√µ' ¥ µ— È ß ‡§√◊ Ë Õ ß Ÿ ß °«à " √–¥— ∫ Õ¬à " ßπâ Õ ¬
❑
Must be installed at the wall, as the picture.
❑
It should be installed above the floor at least 1.70 M.
2)
°"√‡ªî ¥ Ω"§√Õ∫‡§√◊ Ë Õ ßÕÕ°®"°∞"π‡§√◊ Ë Õ ß
Opening of the cover out of the unit base.
❑
∂Õ¥ °√Ÿ à « π≈à " ߢÕßµ— « ‡§√◊ Ë Õ ßÕÕ°
❑
¥÷ ß Ω"§√Õ∫¥â " π∫πÕÕ°
❑
Remove the screw at the bottom of the unit.
❑
Pull off upper cover.
3)
µ' ¥ µ— È ß µ— « ‡§√◊ Ë Õ ß∫πºπ— ß §Õπ°√' µ Õ' ∞ À√◊ Õ ºπ— ß °√–‡∫◊ È Õ ß¥' π ‡º"
Install on concrete, brick or ceramic wall
❑
„™â «à " π‡®"–√Ÿ ∫ πºπ— ß
❑
Õ¥ª≈— Í ° ‡¢â " ‰ª„π√Ÿ
❑
¢— π °√Ÿ · µà ≈ –µ— « ‡¢â " ‰ª„πª≈— Í ° µÕπ∫π Õßµ— « ‚¥¬§â " ß„Àâ ‡ À≈◊ Õ §«"¡¬"«
3
4
°√Ÿ ‡ Õ"‰«â
∂÷ ß
¡' ≈ ≈' ‡ ¡µ√ µà Õ ‰ª·¢«π™ÿ ¥ ‡§√◊ Ë Õ ß∫π °√Ÿ ·≈â « §à Õ ¬¢— π
4
°√Ÿ ¬ ÷ ¥ ∑— È ß
µ— « „Àâ ¬ ÷ ¥ ·πà π ·≈–Õÿ ¥ √Ÿ ¬ ÷ ¥ °√Ÿ ¥ â « ¬´' ≈ ' ‚ §π
❑
°"√µ' ¥ µ— È ß ∑' Ë · ¢«πÀ— « Ωí ° ∫— « µ' ¥ µ— È ß ∑' Ë · ¢«πÀ— « Ωí ° ∫— « „Àâ Õ ¬Ÿ à „ π√–¥— ∫ ∑' Ë ‡¡◊ Ë Õ
·¢«πÀ— « Ωí ° ∫— « ·≈â « à « π Ÿ ß ÿ ¥ ¢ÕßÀ— « Ωí ° ∫— « µâ Õ ß‰¡à Ÿ ß °«à " à « π∫π ÿ ¥ ¢Õß
µ— « ‡§√◊ Ë Õ ß
❑
À≈— ß ®"°µ' ¥ µ— È ß ‡§√◊ Ë Õ ß‡ √Á ® ‡√' ¬ ∫√â Õ ¬ µâ Õ ßµ' ¥ µ— È ß ™ÿ ¥ Õÿ ª °√≥å ª Ñ Õ ß°— π ·√ߥ— π
πÈ " ‡°' π ‡¢â " °— ∫ µ— « ‡§√◊ Ë Õ ß∑"ߥâ " π∑"ßπÈ " ‡¢â " ∑ÿ ° §√— È ß
❑
Drill holes on the wall.
❑
Insert the plug to the holes.
❑
Tighten two screws in the top plug leaving about 3 to 4 mm.
space. Next hang the heater unit on the screws and move to
tighten the 4 screws and seal the holes with silicone.
❑
Installation the hanger on level properly. If shower head is
hung the highest shower head not over the top of water
heater.
❑
After installation of the heater unit, proceed to install the safety
valve to the until at the water inlet tube.
1.70
‡¡µ√
(Silicone)
&
MEMO
MAX
‡°' π
1.7
‡¡µ√
More than 1.7 M
°√Ÿ ¬ ÷ ¥ ¥â " π≈à " ß
Screw for fastening
25
¡¡.
25
MM.
6
¡¡.
6
MM.
MEMO
MAX
™ÿ ¥ Õÿ ª °√≥å
ªÑ Õ ß°— π
·√ߥ— π πÈ " ‡°' π
Safety valve