Related Manuals for Liesegang 212
Summary of Contents for Liesegang 212
- Page 1 Projector ENGLISH Model No.212 / No.296 FRANÇAIS DEUTSCH ESPAÑOL ITALIANO TECHNICAL...
- Page 2 Projector User's Manual - Operating Guide User's Manual - Operating Guide Thank you for purchasing this projector. WARNING Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. NOTE •...
-
Page 3: Projector Features
Projector Features Projector Features This multimedia projector is used to project various computer signals as well as NTSC/PAL/SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system. -
Page 4: Table Of Contents
Contents Contents Projector Features Multifunctional Settings Preparation Using The Menu Functions Part Names MAIN Menu Projector PICTURE-1 Menu Control Buttons PICTURE-2 Menu Remote control INPUT Menu Setting Up AUTO Menu Arrangement SCREEN Menu Adjusting The Projector’s OPTION Menu Elevator NETWORK Menu Using The Lens shift Buttons Network Setting Up Connecting Your Devices... -
Page 5: Part Names
Part Names Part Names Projector Elevator button Elevator foot Remote sensor Lens cap Lens The picture is projected from here. Filter cover An air filter is inside. Projector (Front/Right) RGB port M1-D port BNC port AUDIO IN 1 port AUDIO IN 2 port CONTROL port NETWORK port AUDIO IN R/L port... -
Page 6: Control Buttons
Part Names (continued) Part Names (continued) Control Buttons STANDBY/ON button KEYSTONE and STANDBY/ON indicator TEMP indicator SEARCH M1-D INPUT LAMP indicator LENS SHIFT FOCUS ZOOM LENS SHIFT buttons RESET INPUT dial COMPONENT ENTER SEARCH button MENU S-VIDEO M1-D indicator RGB indicator VIDEO BNC indicator STANDBY/ON... -
Page 7: Setting Up
Setting Up Setting Up Arrangement WARNING • Before installation, make sure that the projector is turned off and the power code is disconnected. • Do not set up and move the projector, while it is hot. • Install the projector in a suitable environment according to instructions of the “User’s Manual –... -
Page 8: Adjusting The Projector's Elevator
Setting Up (continued) Setting Up (continued) Adjusting The Projector's Elevator WARNING • Do not touch about the lens and ventilation openings during use or immediately after use to prevent a burn. CAUTION • To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. -
Page 9: Connecting Your Devices
Setting Up (continued) Setting Up (continued) Connecting Your Devices WARNING • Whenever attempting to connect other devices to the projector, read thoroughly the "User's Manual - Safety Guide", this manual and the manual of each device to be connected. Incorrect connecting could result in fire or electrical shock. CAUTION •... -
Page 10: Examples Of Connection With A Computer
Setting Up (continued) Setting Up (continued) Please refer to the following (for example) for connecting your devices. See the rear of the projector. You can see the ports. Examples of connection with a computer Computer Projector RGB out RGB cable Audio out Stereo Mini cable AUDIO IN 2... - Page 11 Setting Up (continued) Setting Up (continued) Examples of connection with a VCR/DVD Player VCR/DVD Player Projector CONTROL NETWORK REMOTE CONTROL AUDIO IN1 R-AUDIO IN-L VIDEO Audio out (R) AUDIO OUT R-AUDIO IN AUDIO IN2 CR/PR Ca/Pa RGB OUT Audio out (L) AUDIO IN-L R-AUDIO IN-L VIDEO...
-
Page 12: Connecting The Power Supply
Setting Up (continued) Setting Up (continued) Connecting to a monitor CONTROL NETWORK REMOTE CONTROL AUDIO IN1 AUDIO OUT AUDIO IN2 CR/PR Ca/Pa RGB OUT Monitor Projector R-AUDIO IN-L VIDEO S-VIDEO RGB in RGB cable RGB OUT Connecting to a speaker (with amplifier) CONTROL NETWORK REMOTE CONTROL... -
Page 13: Remote Control
Remote Control Remote Control About The Laser Pointer WARNING • The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. -
Page 14: Operating The Remote Control
Remote Control (continued) Remote Control (continued) Operating The Remote Control CAUTION • Do not disassemble the remote control. • Do not place the remote control near the projector’s lens, fan, or vents. • Do not drop or otherwise expose the remote control to physical impact. •... -
Page 15: Using The Mouse/Keyboard Control Function
Remote Control (continued) Remote Control (continued) Using The Mouse/Keyboard Control Function CAUTION • Before connecting, read the manuals of the device you will connect. Mistaken use of the mouse/keyboard control could damage your equipment. • Only connect to a PC. •... -
Page 16: Power On/Off
Power ON/OFF Power ON/OFF WARNING • When the power is ON, a strong light is emitted. Do not look into the lens or vents of the projector. NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. -
Page 17: Operating
Operating Operating Selecting An Input Signal Select an input signal. I Using the INPUT dial SEARCH button Turn the INPUT dial of the projector. SEARCH M1-D Turning the dial cycles through the input ports as INPUT shown below. Select the signal you wish to project. RESET COMPONENT ENTER... -
Page 18: Selecting The Aspect Ratio
Operating (continued) Operating (continued) Selecting The Aspect Ratio Press the Aspect button to toggle between the modes for aspect ratio. I At a M1-D signal LASER INDICATOR STANDBY/ON VIDEO NORMAL 16:9 LENS SHIFT FOCUS ZOOM – – – ASPECT button BLANK ASPECT LASER... -
Page 19: Adjusting The Picture Position
Operating (continued) Operating (continued) Adjusting The Picture Position This function is available only for RGB signals. memo Press the POSITION button. LASER INDICATOR As illustrated on the right, a STANDBY/ON VIDEO dialog will appear on the LENS SHIFT FOCUS ZOOM screen to aid you in adjusting –... -
Page 20: Adjusting The Volume
Operating (continued) Operating (continued) Adjusting The Volume Press the VOLUME button. VOLUME LASER INDICATOR As illustrated on the right, a dialog STANDBY/ON VIDEO will appear on the screen to aid you LENS SHIFT FOCUS ZOOM in adjusting the volume. – –... -
Page 21: Freezing The Screen
Operating (continued) Operating (continued) Freezing The Screen Press the FREEZE button. As illustrated on the right, a LASER INDICATOR STANDBY/ON VIDEO dialog will appear on the screen, and the screen will LENS SHIFT FOCUS ZOOM – – – FREEZE BLANK ASPECT LASER freeze at the current image. -
Page 22: Displaying The Child Window
Operating (continued) Operating (continued) Displaying The Child Window This feature called "PinP (Picture in Picture)" is available only when a RGB signal is memo selected to main screen. Press the PinP button. LASER INDICATOR The child window with a picture of a video signal STANDBY/ON VIDEO will appear. -
Page 23: Multifunctional Settings
Multifunctional Settings Multifunctional Settings Using The Menu Functions This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION and NETWORK. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. ex. -
Page 24: Main Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU MAIN Menu MAIN BRIGHT PICTURE-1 CONTRAST PICTURE-2 ASPECT INPUT WHISPER NORMAL With the MAIN menu, the items shown in the table below can be AUTO MIRROR NORMAL SCREEN LANGUAGE ENGLISH performed. Perform each operation in accordance with the OPTION [Language] NETWORK... -
Page 25: Picture-1 Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU PICTURE-1 Menu MAIN GAMMA NORMAL PICTURE-1 COLOR BAL R PICTURE-2 COLOR BAL G INPUT COLOR BAL B With the PICTURE-1 menu, the items shown in the table below can AUTO SHARPNESS SCREEN COLOR be performed. - Page 26 Multifunctional Settings (continued) Multifunctional Settings (continued) PICTURE-1 Menu (continued) Item Description Select a command to load or save using the buttons, and then press (or the ENTER) button to perform the function.: LOAD1 LOAD2 LOAD3 LOAD4 SAVE1 SAVE2 SAVE3 SAVE4 MY MEMORY This projector has 4 numbered memories for adjustment data.
-
Page 27: Picture-2 Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU PICTURE-2 Menu MAIN V POSITION PICTURE-1 H POSITION PICTURE-2 H PHASE INPUT H SIZE 1344 With the PICTURE-2 menu, the items shown in the table below can AUTO OVER SCAN SCREEN RESET be performed. Perform each operation in accordance with the OPTION instructions in the table below. -
Page 28: Input Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU INPUT Menu MAIN COLOR SPACE AUTO PICTURE-1 COMPONENT COMPONENT PICTURE-2 VIDEO AUTO INPUT 3D-YCS TURN OFF With the INPUT menu, the items shown in the table below can be AUTO VIDEO NR SCREEN P. - Page 29 Multifunctional Settings (continued) Multifunctional Settings (continued) INPUT Menu (continued) Item Description Select a signal input port for the child window using the buttons. : VIDEO S-VIDEO P.IN P. INPUT memo About the child window, please refer to the section “Displaying the Child Window”.
-
Page 30: Auto Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU AUTO Menu MAIN ADJUST PICTURE-1 POWER OFF 0 min PICTURE-2 POWER ON TURN ON INPUT SEARCH TURN ON With the AUTO menu, the items shown in the table below can be AUTO RESET SCREEN performed. - Page 31 Multifunctional Settings (continued) Multifunctional Settings (continued) AUTO Menu (continued) Item Description Select the TURN ON or the TURN OFF using the buttons. : TURN ON TURN OFF When the TURN ON is selected, detecting no signal cycles through input ports and displays the picture of retrieved signal.
-
Page 32: Screen Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU SCREEN Menu MAIN BLANK BLACK PICTURE-1 START UP ORIGINAL PICTURE-2 MyScreen INPUT MyScreen SIZE With the SCREEN menu, the items shown in the table below can be AUTO MyScreen LOCK TURN OFF SCREEN MENU POSITION performed. - Page 33 Multifunctional Settings (continued) Multifunctional Settings (continued) SCREEN Menu (continued) Item Description Select the TURN ON or the TURN OFF using the buttons. : TURN ON TURN OFF When the TURN ON is selected, the following message function works. The message of the “AUTO IN PROGRESS” for the auto adjustment. The message of the ”NO INPUT IS DETECTED”...
-
Page 34: Option Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU OPTION Menu MAIN VOLUME PICTURE-1 SPEAKER TURN ON PICTURE-2 IR REMOTE INPUT IR REMOTE ID With the OPTION menu, the items shown in the table below can be AUTO LAMP TIME 1234 h SCREEN FILTER TIME 4321 h... - Page 35 Multifunctional Settings (continued) Multifunctional Settings (continued) OPTION Menu (continued) Item Description Pressing the (or the ENTER) button calls the SERVICE SERVICE FANSPEED NORMAL menu. AUTO ADJUST ENABLE SERVICE Menu LENS TYPE AUTO LENS LOCK TURN OFF Select an item using the buttons, and press the : SELECT the ENTER) button to per form each function.
-
Page 36: Network Menu
Multifunctional Settings (continued) Multifunctional Settings (continued) MENU NETWORK Menu MAIN SETUP PICTURE-1 DHCP TURN OFF PICTURE-2 INFORMATION INPUT RESET This projector provides the NETWORK function. If you use this AUTO SCREEN function, please set up the projector according to the Network OPTION environment in which you use it. -
Page 37: Network Setting Up
Network Setting Up Network Setting Up This projector provides the NETWORK function. If you use this function, please consult your dealer for information. To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-T) cable, then set up the projector according to the Network environment in which you use it. When you use a Network unsuitable to the DHCP function Please set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using the NETWORK menu, referring to the section “NETWORK Menu”. -
Page 38: Lamp
• Use only the lamp of the specified type Model No.212: ZU0212044010 (DT00601) / Model No.296: ZU0296044010 (DT00591). • If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. -
Page 39: Replacing The Lamp
Lamp (continued) Lamp (continued) Replacing The Lamp If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes. -
Page 40: Air Filter
Air Filter Air Filter WARNING • Please carefully read the “User’s Manual - Safety Guide. • Before caring, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. •... -
Page 41: Other Care
Other Care Other Care WARNING • Please carefully read the “User’s Manual - Safety Guide”. • Before caring, make sure the power switch is off and the power cable is not plugged in. • Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately after use prevent a burn. -
Page 42: Troubleshooting
roubleshooting roubleshooting Related Messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company. - Page 43 roubleshooting (continued) roubleshooting (continued) Related Messages (continued) Message Description CLEAN THE AIR FILTER The time the filter timer has counted has reached 100 POWER OFF FIRST, hours. THEN CLEAN THE AIR FILTER. Please clear or change the air filter by referring to the section AFTER CLEANING THE AIR “Air Filter”.
-
Page 44: Regarding The Indicator Lamps
roubleshooting (continued) roubleshooting (continued) Regarding The Indicator Lamps Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company. - Page 45 roubleshooting (continued) roubleshooting (continued) Regarding The Indicator Lamps (continued) STANDBY/ON LAMP TEMP Description indicator indicator indicator Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off, and allow the unit to cool down at Lighting Blinking Turned...
-
Page 46: Phenomena That May Easily Be Mistaken For Machine Defects
roubleshooting (continued) roubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects WARNING • Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company. - Page 47 roubleshooting (continued) roubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects (continued) Reference Phenomenon Cases not involving a machine defect pages The signal cables are not correctly connected. 8, 9 Correctly connect the connection cables. The volume is adjusted to an extremely low level. 19, 32 Pictures are Adjust the VOLUME to a higher level.
-
Page 48: Warranty And After-Service
They will tell you what warranty condition is applied. Specifications Specifications NOTE • This specifications are subject to change without notice. Specification Item Model No.212 Model No.296 Product name Liquid crystal projector Panel size 2.5 cm (0.99 type) Liquid... - Page 49 Ed. Liesegang • Volmerswerther Straße 21 • D-40221 Düsseldorf • Postfach 10 35 53 • D-40026 Düsseldorf Telefon (0211) 3901-1 • Telfax (0211) 39 01-227 Internet http://www.liesegang.de • e-mail info@liesegang.de Printed in Japan *QR60261*...
Need help?
Do you have a question about the 212 and is the answer not in the manual?
Questions and answers