Advertisement
Optimizing the Lens Setup
➤
MAIN MENU
EXPOSURE
SHUTTER
Select a shutter speed:
1/60 / 1/50 (default) sec.
FLK (Flickerless) Reduces
on-screen flickering.
Caution
When set to
FLK, SENS-UP is disabled.
AGC
OFF, HIGH, MIDDLE,
(default), LOW.
SENS-UP
Set the Sense-Up function.
Move the joystick control
Left/Right to select:
AUTO mode to then select
a value from x2 to x256, or
OFF (default) mode.
BLC
Backlight compensation.
Control the light level to
GAIN
MIDDLE
overcome severe
DEFAULT
backlighting conditions.
LEFT/RIGHT
4
Select from:
WIDTH
4
TOP/BOTTOM
3
OFF (default)
HEIGHT
4
BLC to set the gain.
RETURN
RET
HSBLC to set the image
sensitivity level, from 1 to 8.
BLC and HSBLC both have
an AREA SETUP submenu.
D-WDR
Digital wide dynamic range.
Select from:
OFF (default)
INDOOR
OUTDOOR
➤
MAIN MENU
WHITE BALANCE
AWB
Controls color on the
screen.
ATW (Auto Tracing White
Balance) Select when the
scene illumination varies
between indoor scenes and
outdoor scene lighting.
AWB (Auto White Balance)
(default)
AWC Automatically adjust
the white balance to your
specific environment. Press
SET to adjust.
MANUAL. In Manual mode
you can adjust the red and
blue settings, from 0 to 100.
INDOOR
OUTDOOR
Setting Day/Night Control
➤
Use this menu to set
MAIN MENU
DAY/NIGHT
how the camera adjusts to low light.T
AUTO
COLOR
BW
RETURN
RET
AUTO (default)
Depending on light level,
the camera automatically
switches from color to
DELAY
15
black and white. Select this
D-->N
27
N-->D
13
mode to set:
RETURN
RET
DELAY: Set the time before
the camera switches to Day
or Night mode after
detecting a switching
threshold.
D-->N (Day to Night): The
relative light level at which
the camera switches to
Night mode. The higher the
value, the darker the
lighting (the lower the lux)
must be before the camera
switches.
Set D-->N should be set at
least 3 less than N-->D.
N-->D (Night to Dayl): The
relative light level at which
the camera switches to Day
mode. The lower the value,
the brighter the lighting (the
higher the lux) must be
before the camera
switches.
DAY/NIGHT mode must be
set to AUTO to use this
function.
COLOR
Forces the camera to stay
in Day (color) mode at all
times.
B/W
Forces the camera to stay
in Night (B/W) mode at all
times. The B/W submenu
allows you to select Color
Burst to be ON or OFF.
Note
Certain video
recorders require color
burst to operate.
Setting the Digital Noise Reduction
To set the digital 3D noise reduction function,
select MAIN MENU, then 3DNR. Options are:
ON (default) or OFF, where you can adjust the
level from 0 to 100.
SPECIAL Menu Functions
.
➤
MAIN MENU
SPECIAL
CAM TITLE
OFF
D-EFFECT
MOTION
OFF
PRIVACY
OFF
SYNC
INT
VER. A00003
RETURN
RET
CAM TITLE
Set to ON to add a camera
title (up to 15
characters).You can also
select where the title
appears on the monitor
screen.
D-EFFECT
Digital Effects. D-EFFECT
options are:
FREEZE
OFF
MIRROR: OFF (default),
MIRROR
OFF
ROTATE, V-FLIP, MIRROR
D-ZOOM
OFF
GAMMA
0.45
D-ZOOM:
NEG. IMAGE
OFF
•
ON = D-ZOOM
RETURN
RET
submenu where you
can adjust PAN, TILT.
•
OFF (default)
GAMMA: Set the value,
from 0.05 to 1.0 (0.45 is
the default and is typically
the default value for CCTV
CRT monitors)
NEG. IMAGE: ON, OFF
(default)
MOTION
Detect moving objects on
screen. Select up to 4
areas on screen you want
to observe. You can also
set the motion detection
sensitivity, from 0 to 40.
WIDTH: [values]
TOP/BOTTOM: [values]
HEIGHT:
SENSITIVITY: 0 to 40
MOTION VIEW:
•
ON = the image
flickers when the
camera detects
moving objects.
•
OFF = the monitor
displays MOTION
DETECTION.
PRIVACY
Mask up to 8 privacy areas
on the screen from video
monitoring.
AREA DISPLAY
LEFT/RIGHT:
WIDTH:
TOP/BOTTOM:
HEIGHT:
COLOR: Select one of 15
colors for the privacy zone.
SYNC
Select the Sync mode,
from:
INT (Internal, is the default)
LL (Line Lock). LL only
works with AC power.
VER.
Displays the firmware
version on the camera.
Set the Image Sharpness Level
To set the level of sharpness of the image,
➤
select MAIN MENU
ADJUST. In the
ADJUST submenu you can adjust the
SHARPNESS, from 0 to 31 (16 is the default).
OSD Default Settings
To restore the factory default settings, select
➤
➤
SETUP
RESET
FACTORY.
Completing the Installation
Attaching and Securing the
Dome Cover
To attach the dome cover, follow
Figure
7:
1.
Use a soft, lint-free cloth to wipe the dome
cover clean and remove fingerprints.
2.
Attach the inner liner (#4) to the Tilt adjust-
ment thumbnuts (#2). Push the unit down
until it clicks into place.
3.
Place the dome housing and bubble (#5)
on the camera base (#1).
4.
Align the line markers on the dome
housing with those on the base. Turn the
dome housing gently clockwise until it
locks in place.
5.
Secure the dome cover to the camera base
with the TP1.7 screw (#6).
Figure 7 Dome Housing Installation
1
3
4
5
Legend
1
Camera base
2
Line markers
3
Tilt adjustment thumbnuts
4
Inner liner
5
Dome housing and bubble
6
TP1.7 screw
Routine Maintenance
•
The dome bubble is an optical part. Use a
soft, dry cloth to remove any fingerprints or
dust.
•
Clean the camera housing with a soft, dry
cloth. For more stubborn stains, use a cloth
dampened with a small quantity of neutral
detergent, then wipe dry.
Caution
Do not use volatile solvents such as
alcohol, benzene or thinners to avoid
damaging the surface finish.
Product Dimensions
Figure 8 Camera Dimensions
4.41
"
(112.1 mm)
(Min.) 3.23
"
(82 mm)
(Min.) 3.39
"
(86 mm)
Accessory Mounting Application
When required, you can use the camera
mounting holes (see
Figure
8) to fit the camera
base easily on a single gang electrical box using
the HD3-MK pendant/wall mount kit. For more
information, contact Honeywell Technical
Support or your sales representative (see back
cover for contact information).
Warranty and Service
Subject to the terms and conditions listed on the
Product warranty, during the warranty period
Honeywell will repair or replace, at its sole
option, free of charge, any defective product
returned prepaid.
In the event you have a problem with any
Honeywell product, please call Customer
Service for assistance or to request a Return
Merchandise Authorization (RMA) number.
Call 1.800.796.CCTV (North America only).
Be sure to have the model number, serial
number, and the nature of the problem available
for the technical service representative.
Prior authorization must be obtained for all
returns, exchanges, or credits. Items shipped
to Honeywell without a clearly identified
Return Merchandise Authorization (RMA)
number may be refused.
Specifications
2
Video Signal
NTSC
Specifications
Video Standard:
6
Scanning
525 lines, 2:1 Interlace
System:
Image Sensor:
1/3" SuperHAD2 (Sony CCD)
Number of Pixels
768 x 494
(H x V):
Minimum
0.2 lux @ F1.2 (AGC on, 50 IRE)
Illumination:
Horizontal
520 TVL
Resolution:
Video Output:
1.0 Vp-p @ 75 Ohms
Sync System:
12 VDC: Internal, 24 VAC: Line lock
S/N Ratio:
<50 dB (AGC Off)
Auto Electronic
1/60 - 1/100,000
Shutter:
sec
AI/AES Selection:
On/off, switchable
White Balance:
ATW/AWB/AWC > Set/Manual/
Indoor/Outdoor
BLC
Off/BLC/HSBLC
Gamma:
0.45, adjustable
Sense-Up:
Off/Auto, selectable
D-WDR:
Off/Indoor/Outdoor, selectable
Privacy Mask:
8 mask areas, configurable
Motion Detection:
4 motion detection areas,
configurable
Mirror:
Off/Mirror/V-Flip/Rotate, selectable
3DNR:
Off/On, adjustable
Lens Type:
2.8 mm to 10.5 mm Vari-focal Auto
Iris, F1.2
Lens Iris Control:
Direct Drive (DC) AI
Angle of View
Horizontal: 76.1° (wide), -23.8° (tele)
(Lens):
Vertical: 55.8° (wide), -17.9° (tele)
Electrical Specifications
Input Voltage:
12 VDC/24 VAC
Input Tolerance:
± 15%
Power
3.5 W (max)
Consumption:
Mechanical
Dimensions
4.41" x 3.97" (112.1 mm x 100.6
(WxH):
mm)
Weight:
.66 lbs (.3 Kg) Net, 1.32 lbs (.6 Kg)
Shipping
Construction:
Housing and dome: Polycarbonate
Environmental
Temperature:
Operating: -14°F to 122°F (-10°C to
50°C)
Storage: -4°F to 140°F (-20°C to
60°C))
Relative
0% to 90%, non-condensing
Humidity:
Regulatory
Emissions
FCC, CE (EN55022)
Immunity
CE (EN50130-4)
Safety
EU: LVD 2006/95/EC
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
© 2010 Honeywell International Inc.
Document 800-05724 – Rev C – 05/10
PAL
811 x 508
1/50 - 1/100,000
sec
Advertisement
