Table of Contents
Advertisement
Quick Links
Instruction Manual
IV-08MP
LCD monitor
• This manual was written with the utmost care. However, if you have any question or
inquiries concerning the product, please feel free to contact our dealers or service agents.
• Copying all or part of this booklet is prohibited.
• The contents of this manual may be revised or modified for improvement without prior
notice.
Version 1.0
Produced in Jan. 2004
Thank you for purchasing the SHARP IV-08MP LCD
monitor. Read this introductory instruction manual
carefully to thoroughly familiarize yourself with the
functions and proper procedures for operation.
Notes
TOP - 1
Advertisement
Table of Contents
Related Manuals for Sharp IV-08MP
Summary of Contents for Sharp IV-08MP
- Page 1 Version 1.0 Produced in Jan. 2004 Thank you for purchasing the SHARP IV-08MP LCD Instruction Manual monitor. Read this introductory instruction manual carefully to thoroughly familiarize yourself with the IV-08MP functions and proper procedures for operation. LCD monitor Notes • This manual was written with the utmost care. However, if you have any question or inquiries concerning the product, please feel free to contact our dealers or service agents.
- Page 2 Components of IV-08MP The components of IV-08MP are as follows. One(1) LCD monitor IV-08MP • Four (4) Main housing angle brackets • Two (2) Controller angle brackets • Two (2) Securing screws • One (1) Stylus pen • One (1) Instruction manual...
-
Page 3: Safety Precautions
Safety Precautions Read this instruction manual and the attached documents carefully before installing, operating, or per- forming any maintenance, in order to keep the machine working correctly. Make sure you understand all of the equipment details, safety information, and cautions before using this machine. In this user's manual, the safety precautions are categorized as "Caution". - Page 4 The touch panel provides a function to enter various settings to the con- troller (IV-S51M) by simply touching the screen. Also, since the IV-S51M can be connected directly to the backside of the IV-08MP to be used as one unit, the space required to install the unit will be smaller. Features Thin and light weight.
-
Page 5: Precautions For Use
2. Precautions for Use Pay attention to the points below when handling the IV-08MP. (1) Installed location and environment • Use the equipment in the environment where the ambient temperature is 0~40°C and the relative humidity is less than 90% RH. If the ambient temperature is out of the above range, install a forced fan or an air conditioner to keep the temperature within the required range. -
Page 6: System Configuration
3. System Configuration IV-S50 series controller can be directly connected to the backside of the IV-08MP monitor and used as one unit. IV-08MP can also be connected to the controller using the monitor cable. Direct connection IV-S51M IV-08MP Connection using monitor cable... -
Page 7: Part Names And Functions
4. Part Names and Functions (Front) (Side) TFT LCD panel (touch panel) Power supply input terminal Stylus pen (Bottom) Power supply input terminal Monitor input connector Connector for direct FG OV 24V mounting (Backside) 4 - 1... - Page 8 (Note) Use the stylus pen (provided with the equipment) or the USB connected mouse (not provided with the equipment). Never use the sharp-pointed object such as a pencil or a mechanical pencil which will damage the display. 4 - 2...
-
Page 9: Installation Method
5. Installation Method [1] Installation of IV-08MP Secure the IV-08MP using four (4) mounting holes of the main housing angle brackets (four (4): provided with the equipment). +0.5 +0.5 Cut out the panel ( 228.0 × 186.0 mm) of the mounting surface (thickness: max.7 mm) to fit the IV-08MP into the surface. - Page 10 Mounting holes of the main housing angle brackets (total 4 locations including the lower part) IV-08MP Dimensions of the cut panel The dimensions of the cut panel will be the same in either case where only the main unit is mounted or directly connected to the controller.
- Page 11 Insert four (4) main housing angle brackets (2 each at upper and lower) into the mounting holes of the IV-08MP, and secure the IV-08MP to the mounting area with champing screws of the main housing angle. Tightening torque: 0.3 ~ 0.4Nm (unite: mm) Max.
- Page 12 External dimensions (main housing) 113.5 113.5 74.2 12.5 12.5 POWER 46.1 14.55 51.1 65.65 25.24 12.38 12.38 25.24 74.2 (A view on arrow) 5 - 4...
- Page 13 External dimensions (When directly connected to the controller) 14.55 100.7 115.25 85.3 30.3 126.4 (A view on arrow) 5 - 5...
-
Page 14: Connection Method
Remove the connector cover from the main housing of IV-S51M. Connector cover Fit the tab A of the IV-08MP in the notch part of the IV-S51M. Tab A To connect them, press the IV-S51M in place in the direction of the arrow so that the tab B is fit into the notch part. - Page 15 Insert two (2) main housing angle brackets (supplied with IV-08MP) as indicated below and secure them with two (2) securing screws (supplied with IV-08MP). Main housing angle brackets (2) When IV-08MP is connected to the controller using the monitor cable Connect the monitor output connector of the IV-S51M and the monitor input connector of the IV- 08MP using the IV monitor cable (IV-S50MC2).
- Page 16 Connecting a commercially available constant-voltage power supply to the power terminal (POWER: +24V, 0 V) on the IV-08MP. Use a 24V DC±10%, 800mA or more constant-voltage power supply. • Use an individual power supply to supply power to the IV-08MP.
-
Page 17: Specifications
+0.5 Dimension of cut panel Weight Approx. 1.0 kg * The operation ambient temperature means the ambient temperature at not only the panel mounting side but at all around the IV-08MP. (2) Performance specifications Item Specifications Display device TFT LCD module...