Advertisement
Final Assembly
Step 1: Insert the neck of the fan head into the hollow end of the pole
and turn the neck clockwise to lock into place.
Step 2: Attach the front of the 1 Touch™ control module by sliding the 2
tabs into the corresponding holes on the pole.
Step 3: Attach the rear of the 1 Touch™ control module to the front by
inserting the 4 clips into the corresponding holes.
Step 4: For additional security, insert and tighten the thumbscrew into
the top rear of the 1 Touch™ control module.
OPERATING INSTRUCTIONS
Your fan is equipped with the technologically advanced 1Touch
thermostat. You can set the fan from either the main housing or the
remote control to run continuously in manual mode ore set the 1Touch
thermostat to your desired temperature setting. The 1Touch
will automatically turn the fan ON or OFF depending on the preset
comfort level. The comfort level ranges between 60° and 80° Fahrenheit.
• Set the fan base on a dry, level surface.
• Plug the fan into a 120V AC electrical outlet
• To start the unit and run continuously, push the button on the fan
housing or on the remote control once for the High setting and press
either button twice for the Low setting
• To stop the unit, press and hold the button on the fan housing or on
the remote control for two seconds or keep pressing the button until
all the speed and temperature indicators are OFF
• The OSCILLATION control knob is located on the top of the fan motor
housing. To start oscillation, push knob down. To stop oscillation, pull
knob up
1 Touch
™
Thermostat Instructions
To take advantage of the 1Touch
until the desired temperature is reached. When ambient temperature drops
below the set temperature, the fan will stop. When the room temperature
rises above the set point, the fan will turn on automatically.
Note: It is normal for the fan to cycle ON and OFF as it maintains the
preset temperature. To prevent the unit from cycling, you need to
raise the thermostat setting.
1Touch
™
has memory. The 1Touch
temperature setting after the unit has been turned off. However if the unit
is unplugged, the 1Touch
thermostat will be reset and will no longer
™
remember the previous temperature setting.
FIGURE 2
™
thermostat
Thermostat, continue to press the button
™
™
thermostat will remember the previous
Remote Control Handheld Unit
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zine), or rechargeable (nickel-cadmium) batteries.
ADJUSTMENT INSTRUCTIONS
Tilt Adjustment:
Your fan is equipped with the Total Flex™ tilt adjustment mechanism.
Total Flex™ allows you to angle the fan head to a straight up position.
This position allows for whole room air circulation. Follow these instruc-
tions to tilt the fan head for upward angled air movement or whole-
room air circulation. You may use the oscillation feature in this position.
Step 1: To change the tilting angle of the fan head; simply loosen the Tilt
Adjustment Knob (see figure 1).
Step 2: Move the fan head to the desired angle, and firmly tighten the
knob to lock in place.
Height Adjustment
Step 1: Turn the base collar counter-clockwise to loosen the extension pole.
™
Step 2: Adjust the extension pole to the desired height, and firmly
tighten the base collar in a clockwise direction.
™
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for your Holmes
stand fan. Please remember:
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline, thinner, benzine
(See instructions for fan head assembly)
Step 1: To access the fan blade, remove the front grill and the fan blade
nut.
Step 2: Clean the fan blade, both front and rear grills with a soft cloth
moistened with a mild soap solution.
Step 3: Replace blade, tighten the blade nut, and securely fasten the
front grill.
Fan Head, Base, and Pole Cleaning
Using a soft, moist cloth, with or without a mild soap solution, carefully
clean the fan base, pole, and head. Please use caution around the motor
housing area. Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
Your fan can be stored in the off-season either partially disassembled or
assembled. It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using the original
(or appropriately sized) box.
• If stored assembled or partially assembled, remember to protect the
fan head from dust.
Your remote control requires 2 AAA batteries for
operation. To install the batteries, simply depress the back
of the remote with your thumb on the spot marked OPEN.
Insert batteries according to the diagram shown inside.
Replace Cover.
Advertisement
