Using The Call Function; Using The Monitor Function; Turning On Or Off The Button Press Beep; Turning On The Display Backlight - Midland G-11 Owner's Manual

OWNER'S MANUAL FOR THE G-11 (GMRS)

USING THE CALL FUNCTION

Press and release the "CALL" button (5) on the side of the radio.
This will cause the radio to transmit a tone to alert the other people in your group to listen for a
message.
Use of the call function is discouraged if using the 22-405 or the 22-540

USING THE MONITOR FUNCTION

1. Press and release the "MON" button (3) on the side of the radio to open the squelch.
This allows you to over ride the squelch and the "CTCSS" or "DCS" tones. This is useful
to monitor the channel before you transmit to ensure there is not someone using the
channel when you have "CTCSS" or "DCS" tones programmed. This is also useful if you
suspect someone in your group does not have the proper "CTCSS" or "DCS" tones
programmed.
2. Press and release the "MON" button or wait 10 seconds to restore the squelch to normal.

TURNING ON OR OFF THE BUTTON PRESS BEEP

1. With the radio turned off, press and hold the "ENTER" button (8) and turn the radio on. The
radio will display all segments available on the display and sound the power up tone. Release
the "ENTER" button when the radio powers up.
depending on the previous setting, and below in smaller letters "BEEP"
2. Press and release the "/\" or "\/" button to change the setting.
3. The setting "oN" is Beep on. The setting "FF" is Beep off.
4. Press and release the "ENTER" button to return to operating mode.

TURNING ON THE DISPLAY BACKLIGHT

Press and release the "ENTER" button (8). A beep will be heard (if enabled). The back-light will
stay on for about 5 seconds then turn off.

TURNING THE ROGER BEEP ON OR OFF

Roger beep is a sound the radio transmits when you release the "PTT" button (4).
1. With the radio turned off, press and hold the "ENTER" button and turn the radio on. The radio
will display all segments available on the display and sound the power up tone. Release the
"ENTER" button when the radio powers up. The display will show "FF" or "oN" depending
on the previous setting, and below in smaller letters "BEEP"
2. Press and release the "F" button once. An icon of a musical note will be displayed above
"oN" or "FF" on the display.
3. Press and release the "/\" or "\/" button to change the setting.
The setting "oN" is Roger beep on. The setting "FF" is Roger beep off.
The Roger beep is the same sound as the Power Up tone
4. Press and release the "ENTER" button to return to operating mode.
Use of roger beep is discouraged when earphones or headsets are in use.

TURNING THE CALL VIBRATOR ON OR OFF

The Call Vibrator feature causes a vibration in the unit when the incoming call signal is received.
To use this feature follow these steps:
1. With the radio turned off press and hold the "ENTER" button and turn the radio on. The radio
will display all segments available on the display and sound the power up tone. Release the
"ENTER" button when the radio powers up. The display will show "FF" or "oN" depending
on the previous setting.
2. Press and release the "F" button twice and the icon
above "oN" or "FF" on the display.
3. Press and release the "/\" or "\/" button to change the setting.
4. The setting "oN" is call vibrator on,
The setting "FF" is call vibrator off.
5. Press and release the "Enter" button to return to operating mode.
http://www.midlandradio.comPage
The display will show "FF" or "oN"
will be displayed (in most units)
8 of 16