Leviton 8” User Manual

Functions

Lamp Installation

Disconnect the unit from power. Open
the lens door by pulling the top of the
door pivot latch towards you. This will
allow the door to swing open, revealing
a lamp carriage assembly with a
lampholder and reflector mounted to
the platform.
To lamp the theatre fixture, Cat.
No. FR2TH, align the flanges of
the prefocus lamp with the
respective indentations of the
prefocus lampholder. Please
note the lamp flanges are
asymmetrical, and the large
lamp flange must align with
large socket indentation. After
alignment, press lamp down by
the ceramic base and twist
clockwise 90° until lamp locks
in position.
To lamp the television fixture,
Cat. No. FR2TV, release the
locking lever of the bipost
socket so the lever is parallel to
the extruded housing. Insert
the bipost lamp into the socket
until the lamp stops, then lock
the lever to the original
position. The socket should
firmly hold the lamp in position.
Be sure that the lever is
completely closed.
Close the lens door until latch engages.
NOTE
Please do not touch the quartz lamp envelope during installation. If this
occurs, clean the lamp with isopropyl (rubbing) alcohol and lint free,
clean cloth.
These Colortran fresnels are UL listed to 2000 watts. Any usage of higher
wattage lamps is improper usage of the fixture and voids any manufacturing
warranties. Please use only the lamps listed in the charts shown here.

Focusing

The Colortran fresnels have an
extremely wide focusing range, with
spot focus applications to 85' and ten
foot projected diameters at only 8' in
full flood focus. The focus system is
simple to operate and maintain.
The focusing is controlled on the right
side of the fixture, simply turn the
handle clockwise for flood focus and
counter clockwise for spot focus.

Beam Control

The fresnel spotlight is a soft focusing projector that may be framed to
reduce flare or direct the light through Colortran barndoors and top hats.
The beam may be further softened through wire scrims or filters. Color
temperature may be shifted with Colortran dichroic glass filters, or normal
color medium.
The Colortran fresnels accept industry standard 10" x 10" accesories,
allowing the fixtures to accept automated color changers, liquid crystal
strobe effects and many other items.

Color

Lee Color Effect Filters are recommended for all filter applications. These
filters are available in over 175 colors, color corrections, and diffusion
selections. Lee Filters are available in both 21" x 4" sheets and 25' x 4' rolls.
LIMITED TWO YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of
anyone else that this product at the time of its sale by Leviton is free of defects
in materials and workmanship under normal and proper use for two years
from the purchase date. Leviton's only obligation is to correct such defects by
repair or replacement, at its option, if within such two year period the product
is returned prepaid, with proof of purchase date, and a description of the
problem to Leviton Manufacturing Co., Inc., Att: Service Department, 20497
SW Teton Ave., Tualatin, Oregon 97062. All products returned to Leviton-
NSI must have factory authorization for return prior to shipping. The purchaser
is responsible for completing and mailing to Leviton, within 15 days of purchase,
the warranty registration card enclosed with each product. This warranty
excludes and there is disclaimed liability for labor for removal of this product
or reinstallation. This warranty is void if this product is installed improperly or
in an improper environment, overloaded, misused, opened, abused, or altered
in any manner, or is not used under normal operating conditions or not in
accordance with any labels or instructions. There are no other or implied
warranties of any kind, including merchantability and fitness for a particular
purpose, but if any implied warranty is required by the applicable jurisdiction,
the duration of any such implied warranty, including merchantability and fitness
for a particular purpose, is limited to two years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation,
damage to, or loss of use of, any equipment, lost sales or profits or delay or
failure to perform this warranty obligation. The remedies provided herein are
the exclusive remedies under this warranty, whether based on contract, tort or
otherwise.

Maintenance

Reflector
The reflector may be accessed by
opening the lens door. Remove lamp
to access reflector surface for
cleaning. The Alzak ® finish requires
little maintenance, occasionally wipe
with isopropyl (rubbing) alcohol, and a
lint free cloth. Strong alcohol or acidic
cleaners MUST NOT be used.
Lens
The lens will become dirty due to
environmental conditions. To
clean, use a lint-free cloth and
rubbing alcohol. Do not use
commercial lens cleaners. If
significant dirt and grime exist,
remove the lens from the fixture
and place lens in clean water
WITHOUT SOAP. Rinse grime
away, clean the reflector with
alcohol.
Focus System
The rack and pinion focus system can
lose tension over long periods of time
by expansion and contraction of the
fixture housing and components, or
the gear itself could move causing
improper fitting against the cast rack.
Both items are easily resolved.
The tension is adjusted by turning the
center screw within the focus handle
while the fixture is aimed 90 degrees
down, so the full weight of the
lampholder assembly bears on the
focus gear. Tighten the screw until the
assembly does not move. Do not over
tighten.
The focus gear should interface
smoothly with the rack on the focus
platform. To adjust, aim fixture to a
horizontal axis or place unit on a table.
Remove the focus handle. Loosen but do
not remove the screws on each side of
the focus gear. Reach inside the fixture
and move the socket assembly manually.
Adjust the focus gear so the assembly is
halfway between maximum possible
engagement into the rack and the point
where gears will slip. Tighten the two
screws when focus gear reaches that
point.
The focus assembly will grind against the rack if engaged too deeply, and
gears will slip if adjustment is too high.
Recommended Lamps for 8" Theater Fresnel
Part Color Life
Watts No. ANSI Temp. (Hrs.)
2000 176-194 BVW 2000W, 250 hr., 3200°K, 120V
1500 176-193 CWZ 1500W, 325 hr., 3200°K, 120V
1000 176-192 BVV 1000W, 200 hr., 3200°K, 120V
1000 176-191 BVT 1000W, 500 hr., 3050°K, 120V
2000 6994C 2000W, 400 hr., 3200°K, 220/240V
1000 T-16 1000W, 750 hr., 3050°K, 220/240V
1000 T-2 1000W, 200 hr., 3050°K, 220/240V
Recommended Lamps for 8" Television Fresnel
Part Color Life
Watts No. ANSI Temp. (Hrs.)
2000 176-075 CYX 2000W, 200 hr., 3200°K, 120V
1500 176-157 CXZ 1500W, 300 hr., 3200°K, 120V
1000 176-161 CYV 1000W, 200 hr., 3200°K, 120V
2000 476-055/056 CP41 2000W, 200 hr., 3200°K, 220/240V
650 476-048/049 CP39 650W, 100 hr., 3200°K, 220/240V

Accesories

Part No. Description
000-A2KBD-000 Eight leaf barndoor
000-A2KCF-000 Diffusion frame
000-A2KSS-000 Set, single, half/single scrim
000-A00CS-000 Combo stud for flat yoke
000-A2KTH-000 8" Top hat
000-A00CC-000 C-clamp for 1" or 2" I.D. pipe

Photometric Performance

8" Theater Fresnel, Cat. No. FR2TH, with lamp No. 176-194, 2000W
ANSI Code BVW
For field diameter at any distance, multiply that distance by 0.269 for
spot and 1.238 for flood.

Beam Candlepower

Spot 358,000
Flood 37,000
8" Television Fresnel, Cat. No. FR2TV, with lamp No. 176-075,
2000W ANSI Code CYX
For field diameter at any distance, multiply that distance by 0.265 for
spot and 1.32 for flood.
Leviton NSI-Colortran Fresnels utilize the latest advances in lighting
Beam Candlepower
technology to provide the best quality fixture in the market. These
operating guide will help you to become more familiar with your spotlight.
Spot 358,000
The major components of the fresnel are:
Flood 39,500
1
2
3
4
8" THEATRE AND
TELEVISION FRESNELS
USER GUIDE
The door assembly — Includes the lens door, accessory clips,
latch mechanism, safety latch and the fresnel lens.
The lamp carriage — Includes the lampholder, wiring, reflector
and the lampholder platform and associated parts.
The focus system — Includes the focus handle, pinion gear and
associated hardware.
The housing — Includes the extruded housing, cool focusing
handles, and simple, rugged design.
PK-93196-00-01-1A