Sharp AR-M208 Service Manual page 22

26-14
Function Used to input the Software Key for the PS extension
(Purpose) kit.
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the PS expansion kit soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
(Initial screen) (In case of OK)
Sim26-14 PS KIT KEY
Sim26-14 PS KIT KEY
PS KIT KEY
PS KIT KEY ON
----------
----------
----------
----------
After canceling the simulation, if OK, the PS expansion kit function is
enable; if NG, the PS expansion kit function is disabled.
This setting must be reset after the simulation cancel.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL/PS3 is installed.
26-22
Purpose Setting
Function Used to set the specification (language display) for the
(Purpose) destination.
Item Specifications
Operation/procedure
Select the language to be used according to the table below.
This setup varies in connection with SIM 26-6 (Destination setup).
Sim26-22 LANGUAGE
LANGUAGE 0
(0:JAPANESE
1:ENG.US 2:ENG.UK
1/8 [ 0- 20] 0
Display items
0:JAPANESE 11:GREEK
1:ENG.US 12:POLISH
2:ENG.UK 13:HUNGARIAN
3:FRENCH 14:CZECH
4:GERMAN 15:RUSSIAN
5:ITALIAN 16:FINNISH
6:DUTCH 17:NORWEGIAN
7:SWEDISH 18:DANISH
8:SPANISH 19:CHINESE
9:PORTUGUESE 20:TAIWANESE
10:TURKISH
26-41
Purpose Setting
Function Used to set whether the automatic magnification ratio
(Purpose) select (AMS) is always ON or not when setting the
pamphlet (center binding) function.
Item Operation
Operation/procedure
AMS mode is set when setting the pamphlet (center binding) function.
Sim26-41 PAMPHLET
AMS MODE SET 0
(0:OFF 1:ON)
[ 0- 1] 0
(In case of NG)
Sim26-14 PS KIT KEY
OK
PS KIT KEY
----------
----------
Setting
Default
range
0-20 1
–
AR-M208 SIMULATION 8 - 8
Display items
0:OFF
1:ON
26-57
Purpose Setting
Function Used to set the model code.
(Purpose)
Item Operation
NG
Operation/procedure
Input the set value with the 10-key and press the [OK] key.
Sim26-57 MACHINE
MACHINE CODE
(1:AR-265G
2:AR-265FG
1/3 [ 1- 6]
Display items
1:AR-265G
2:AR-265FG
3:AR-5127
4:AR:265S
5:AR-265FP
6:AR-M208
If a model different from CPM setup (22cpm or 27cpm) of BOOT is set,
a system error will occur after canceling the simulation.
43
43-1
Purpose Setting
Function Used to set the fusing temperature in each operation
(Purpose) mode.
Section Fixing (Fusing)
Item Operation
Operation/procedure
After the mode selection, enter the adjustment value and press the
[OK] key.
(Initial screen)
Sim43-1 FUSER TEMP.
1:600dpi
2:1200dpi
3:POST CARD
Display items
1:600dpi
2:1200dpi
3:POST CARD
Content Setting range
AMS is not set
automatically.
AMS is set automatically.
1
1
Setting range Default
1-6
(Input screen)
Sim43-1 FUSER TEMP.
185
2:1200dpi 160
160
185
2
[140-190] 160
Content Setting range
600dpi 155-190
1200dpi 140-190 Disabled
Postcard 155-190
Default
0-1 0
1
Default
185
185