Advertisement
Quick Links
SH87R6 Quick Guide【 English 】
Front Panel
F1. 5.25" Bay
F2. 3.5" Bay
F3
F1
F3. Eject Button
F4. Open Door
F2
F5. Power Switch
F4
F6. Power LED
F7. HDD LED
F7
F6
F5
F8. USB3.0 Ports
F8
F9
F11
F9. USB2.0 Port
F10. Mic In
F11. Headphone
F12
F10
F12. USB2.0 Port & Fast Charger
Back Panel
B1. AC Power Socket
B16
B2. Serial Port (Optional)
B3. S/PDIF Out Port
B4. DVI-I Port
B5. HDMI Port
B6. USB2.0 Ports
B7. eSATA Port
B1
B8. LAN Port
B9. USB3.0 Ports
B2
B3
B10. Clear CMOS Button
B10
B6 B8
B11. Front Speaker Out (L/R) Port
B12
B12. Line-In Port
B13
B13. Side Speaker Out (L/R) Port
B14
B14. Real Speaker Out (L/R) Port
B15. Center/Subwoofer
Speaker Out Port
B16. Wireless LAN Perforation
B4
B5
B7
B9
B11
B15
B6
(Optional)
Motherboard Illustration
2x USB 3.0 Ports
Clear CMOS Button
2x USB 2.0 & 1x LAN Ports
Front Speaker Out / Line-In Ports
2x USB 2.0 & 1x eSATA Ports
Side Speaker Out /
HDMI & DVI-I Ports
Real Speaker Out / Center /
Subwoofer Speaker Out Port
J10
Front Audio Header-JP5
AUX_IN Connector
J7
USB Header-USB2
FAN Connector-FAN1
USB Header-USB1
One PCIe x4 Slot
S/PDIF OutPut
Connector-JP2
J6
FAN Connector-FAN2
Intel
J9
USB3.0 Header-JP4
One PCIe x16 Slot
SATA 3.0 Connector-
SATA1,SATA2,SATA3,SATA4
LGA 1150
Mini PCIe slot with
mSATA support
J8
LPC Header-JP1
ATX Power Connector-ATX1
J4
Power Header-JP3
4x 240 pins DDR3 DIMM Slots
Mini PCIe Slot
ATX Power Connector-PWR1
J3
COM Header-COM1
J2
CIR Header-JP6
Jumper Settings
S/PDIF OutPut Connector (JP2)
CIR Header (JP6)
J1
J2
1=5V
1=Ground
2=NULL
2=VCC
3
3=Ground
3=SPDIFO
2
4=GPIO1
1
5=GPIO2
COM Header (COM1)
Power Header (JP3)
J3
J4
1=DCD
2=RXD
1=+HD_LED
3=TXD
4=DTR
3=-HD_LED
5=Ground
6=DSR
5=RST_SW
7=RTS
8=CTS
7=GND
9=Ring
10=NULL
9=NULL
9 7 5 3 1
10 8 6 4 2
Fan Connectors
J6
J5
AUX IN Connector
1=AUX-IN – Left
1=Ground
2=+12V
2=Ground
3=SPEED_SENSE
3=Ground
4=AUX-IN – Right
4=PWM_CTRL
1 2 3 4
J7
USB Header (USB1,USB2)
1=5V_USB
2=5V_USB
3=USB A-
4=USB B-
5=USB A+
6=USB B+
7=GND
8=GND
9=NA
10=NULL
LPC Header (JP1)
J8
1=+12V
2=5V
3=5VSB
4=SERIRQ
5=CLK_48M
6=CLK_33M
7=SIO_RST
8=LFRAME
9=LAD3
10=LAD2
11=-12V
12=3VSB
13=Ring
14=LDRQ0
15=SIO_PME
16=LAD1
17=LAD0
18=+3.3V
19=GND
20=NULL
J9
USB 3.0 Header (JP4)
1=5VCC
2=A_RX_N
3=A_RX_P
4=Ground
5=A_TX_N
6=A_TX_P
11 12 13 14 15 16 17 18 19 20
7=Ground
8=A_Data_N
9=A_Data_P
10=OC
11=B_Data_P
12=B_Data_N
13=Ground
14=B_TX_P
1 2 3 4 5 6 7 8 9 10
J5
15=B_TX_N
16=Ground
17=B_RX_P
18=B_RX_N
J6
19=5VCC
20=NULL
J7
J1
J10
Front Audio Header (JP5)
®
64 Chipset
1=MIC_L
2=GND
3=MIC_R
4=Front_Detect
5=LINE_R
6=Mic_detect
7=sense
8=NULL
9=LINE_L
10=Line_Detect
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same
or equivalent as recommended by Shuttle. Disposal of used batteries according to the
manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classification label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN.AVOID EXPOSURE TO BEAM.
A. Begin Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
2
5 4 3 2 1
1
3. Unfasten the rack mount screws and remove the rack.
2=PWR_LED
4=GND
6=PWR_SW
8=GND
10=NA
9 7 5 3 1
B. CPU and ICE Installation
10 8 6 4 2
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
4 3 2 1
Fan Connector
FAN1/ FAN2
3. Remove the ICE module from the chassis and put it aside.
This 1150 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
2 4 6 8 10
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
Follow the steps below to correctly install the CPU into the
1 3 5 7 9
motherboard CPU socket.
4. Remove the protective membrane from the CPU socket.
A
5. First unlock. Press
with your thumb, then move it to
20
10
released from the retention tab and raise the socket lever.
19
9
18
8
17
7
16
6
A
15
5
14
4
B
13
3
6. Lift the metal load plate on the CPU socket.
12
2
11
1
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
7. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
1
2
3
4
5
6
Triangle Pin1
Marking
Socket
7
8
on the CPU
1150
CPU
9
10
Please be aware of the CPU orientation, DO NOT force the CPU into
the socket to avoid bending of pins on the socket and damage of CPU!
8. Close the metal load plate, lower the CPU socket lever and lock in place.
9. Spread thermal paste evenly on the CPU surface.
L
The product's colour and specification will depend on the actual shipping product.
Please do not apply excess amount of thermal paste.
10. Tear off the protective membrane from the bottom of ICE module.
11. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
12. Connect the fan connector.
Fan Connector
13. Fasten the Smart Fan
to the chassis with the
four thumbscrews.
C. Memory module Installation
Guidelines for Memory Configuration
Before installing DIMMs, read and follow these guidelines for memory
configuration.
Make sure that the motherboard supports the memory.
It is recommended that memory of the same capacity, brand,
speed,and chips are used.
(Go to Shuttle's website for the latest memory support list.)
Memory modules have a foolproof design. A memory module can
be installed in only one direction. If you are unable to insert the
memory, switch the direction.
Dual-Channel mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive
data with two data bus lines simultaneously. Enabling Dual-Channel
mode can enhance the system performance. The following illustrations
explain the population rules for Dual-Channel mode.
A
DIMM1 (Red),Empty
DIMM2 (Yellow),Installed
B
until it is
DIMM3 (Red),Empty
DIMM4 (Yellow),Installed
B
DIMM1 (Red),Installed
DIMM2 (Yellow),Installed
DIMM3 (Red),Installed
DIMM4 (Yellow),Installed
Installing a memory module
DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
Metal load plate
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
A DDR3 memory module has a cutout, so it can only fit in one direction.
1
Cutout
DDR3 240-pin 1.5V
Notch
Latch
72*2=144 pin
48*2=96 pin
2
3
3. Check that the latches are closed, and the memory module is firmly installed.
Thermal Paste
application area
Repeat the above steps to install additional memory modules,
if required.
D. Mini PCIe card Installation
1. Install the Mini PCIe card into the Mini PCIe slot / mSATA Slot and affix it
with screws.
E. Peripheral Installation
1. Loosen the purse lock and separate the Serial ATA and power cables.
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
Serial ATA Optical Drive
Serial ATA HDD
3. Connect the Serial ATA Cable to motherboard.
4. Place the rack in the chassis and refasten the rack.
SATA 3.0 Connectors
5. Connect the Serial ATA and power cables to the HDD.
Serial ATA Cable
Serial ATA Power Cable
6. Connect the Serial ATA and power cables to the optical drive.
Serial ATA Cable
Serial ATA Power Cable
F. Accessories Installation
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
PCIe x4 slot
PCIe x16 slot
2. Install the PCIe x4 / PCIe x16 card into the PCIe x4 / PCIe x16 slots.
3. Secure the bracket.
VGA Card PCB
5mm
34.6mm
Chassis
Cover
Latch
PCIe x16 / PCIe x 4 slots
G. Complete
1. Replace the cover and refasten the thumbscrews.
2. Complete.
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
53R-SH87R3-1001
Advertisement
