Using An Usb Device; Setting The Clock - LG FA164 Owner's Manual

FA164-D0P-DDEULL-ENG 3/11/10

Using an USB device

You can enjoy media files saved on a USB device by connecting the
USB device to the USB port of the unit. If you want to operate other
function, see the "Listening to CDs" section.
1 Open the USB port cover.
2 Connect the USB device to
the USB port of the unit.
3 Select the USB function.
4 Select a file you want to play.
5 Start your media playing.
6 To stop, press
7 Before disconnecting, you have
to change to any other function.
Compatible USB Devices
• MP3 Player : Flash type MP3 player.
• USB Flash Drive : Devices that support USB2.0 or USB1.1.
• The USB function of this unit does not support all USB devices.
• Devices which require additional program installation when you have
connected it to a computer, are not supported.
Look out for the follows
• Do not extract the USB device while in operation.
• For a large capacity USB, it may take longer than a few minute to be searched
• To prevent data loss, back up all data.
• If you use a USB extension cable or USB hub, the USB device is not
recognized.
• Using NTFS file system is not supported. (Only FAT(16/32) file system is
supported.)
• This unit is not supported when the total number of files is 1000 or more.
• External HDD, Card readers, Locked devices, or hard type USB devices are
not supported.
• USB port of the unit cannot be connected to PC.
• The unit can not be used as a storage device.
11:59 AM Page 9
ON REMOTE
ON UNIT
- -
- -
FUNC. FUNCTION
] ] I I I I / i i i i ] ] ./>
B B / / X X B B / / X X
x x x x ENTER
FUNC. FUNCTION

Setting the Clock

1 Turn the power on
2 Press for at least 2 seconds
3 Choose from either
AM 12:00 (for an AM and PM display) or
0:00 (for a 24 hour display)
4 Confirm your selection
5 Select the hours
6 Press
7 Select the minutes
8 Press
Using your player as an alarm clock
1 Turn the power on.
2 Press and hold TIMER Each function, EX) TUNER, CD.... flashes.
3 Press SET when the function you want to be woken by is showing.
4 Choose one of them by pressing SET.
5 "ON TIME" will be displayed. Then you can set the time you want the alarm to
go on. Press ] ] I I I I / i i i i ] ] to change the hours and minutes and SET to save.
6 "OFF TIME" will be displayed. Then, you can set the time you want the function to
stop. Press ] ] I I I I / i i i i ] ] to change the hours and minutes and press SET to save.
7 You will be shown the volume (VOL) you want to be woken by.
Use ] ] I I I I / i i i i ] ] to change the volume and SET to save.
The clock icon " "shows that the alarm is set.
8 Press TIMER button 2times. You can check the setting status.
Notes:
• If you set the clock time, you can check the time by pressing CLOCK even
when the player is turned off.
• If you set the clock time and alarm, you can check the alarm icon "
pressing CLOCK even when the player is turned off.
Setting the asleep time
1 Press SLEEP repeatedly to select delay time between 10 and 180 minutes,
after the unit will be turned off.
2 To check the remaining time, press SLEEP.
3 Press SLEEP once while "SLEEP 10" is displayed, to deactivate sleep function.
ON UNIT
1 1 /] ]
CLOCK
] ] I I I I / i i i i ] ]
SET
] ] I I I I / i i i i ] ]
SET
] ] I I I I / i i i i ] ]
SET
" by
9