COLOUR MONITOR CM650ET EasyMenu ! with EasyMenu is HITACHI’s On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. SERIAL No.
NOTE: The information in this manual is subject to change without notice. responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA is a registered trademark of International Business Machines Corporation. VESA is a trademark of a nonprofit organrsation, Video Electronics Standard Association S.r.x@ is a trademark of Environmental Protection Agency (EPA).
Congratulations! You have just purchased a TC0’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment.
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE- 114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): email@example.com Current information regarding TCO’99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements...
FEATURES ... I - 1 CAUTIONS ... INSTALLATION ... STANDARD SETTINGS..OPERATION..AUTOMATIC SIGNAL CHECK..I - 11 POWER MANAGEMENT SYSTEM.. PLUG & PLAY..SPECIFICATIONS..The following features are provided by the Colour Monitor. Sharpest Focus and Highest Contrast Flat screen Enhanced Dot Pitch (EDP) CRT with FS double focus and AR-ASC coating gives the sharpest focus and highest contrast to minimise eye fatigue.
NEVER REMOVE THE REAR COVER ! __ The rear cover MUST be removed only by authorised service personnel. This colour - monitor contains high voltage components. .: n THE POWER POINT SHOULD BE CLOSE TO THE MONITOR AND EASILY ACCESSIBLE ! INSTALL THE UNIT IN AN SUITABLE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard.
CAUTION for 200 - 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over-current protection. Refer to the following table for the suitable number and location of the protective devices which should be provided in the building installation. PROTECTIVE DEVICES IN SINGLE - PHASE EQUIPMENT OR SUB -ASSEMBLIES Equipment to be connected to Earth faults POWER SYSTEMS with earthed Over-current...
H FCC (Federal Communications Commission) STATEMENT WARNING WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. to provide reasonable protection against harmful interference in a residential installation. -a This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to .- radio communications.
FOR THE CUSTOMERS IN THE U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
Install the monitor in the following way, taking care to maintain safety FRONT VIEW Control Panel Tilt & Swivel Base v (for optional USB HUB Module) 1. Installation Install the monitor on a horizontal base. 2. Power Cord Connection @ Make sure of using the power cord meeting the safety standard of the country in which you are using the monitor.
Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been pre- programmed by the factory. Video Mode Name (with Resolution and Vertical Frequency) 640 x 400- 70 Hz 2 VESA 640 X 400- 85 Hz 3 VESA 800 600- 85 Hz VESA 1024 x...
Switches Switches POWER ON/OFF Press the Power switch, to switch the power ON or OFF. n When power is ON, the power LED lights. After turning OFF the switch, wait at least 5 seconds before restarting the monitor. Otherwise the monitor may operate incorrectly. H If the picture doesn’t appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds before restarting the monitor.
Table-l Function PINCUSHION PIN BALANCE recalls the factory preset modes. When the Blue or Red the upper limit, it makes the reaches the upper limit, it Blue and Red weaker. make the Green weaker. B makes the Red and Green makes the Blue stronger. stronger.
Table-l (continued) Function B H.MOIRE V.MOIRE LANGUAGE a SELECT POWER m MANAGEMENT AUTO SAVE SJEJ DEGAUSS EXIT makes the operation of makes the operation of horizontal moire circuit horizontal moire circuit weaker. makes the operation of makes the operation oi vertical moire circuit weaker.
When the monitor has detected the change of the signal input condition, the monitor will indicate the condition automatically, as follows. the horizontal frequency Precision frequency, Horizontal *2kHz EDGY STAR@, This monitor meets the The monitor has a built-in power management system that standard specifications.
= C R T input Signal Synchronisation Resolution Video Clock frequency Viewable Image Size Viewable Image Area Colour Temperature Warm-up Time Power Supply Dimensions Weight Environmental Condition USB HUB (optional) Specification and Design are subject to change without notice. 1 - 1 2 17 inch picture tube, 0.22 mm horizontal dot pitch (0.21 mm horizontal mask pitch)