Advertisement
Disclaimer
This manual is intended only as a guide for Antec's Computer Enclosures.
For more comprehensive instructions, please refer to the user's manuals
which come with your components and drives.
Basics
1.
Take the case out of the box.
2.
Remove the Styrofoam.
3.
Remove the plastic bag.
4.
Place the case upright with the power supply fan at the back facing
you on a stable flat surface.
5.
Remove the thumb screw which fasten the top cover onto the case.
This is the only screw you need to remove to open the case. Keep this
screw separate from the other screws.
6.
Grip both sides of the top panel with your hands. Slide and lift it up.
7.
From the top of the case, under the large middle metal tab (that is
folded over the top of the chassis, ie not sticking up), carefully insert a
flat head screw driver into the seam between the side panel and the
metal chassis. Gently lift and pull the side panels out.
Note: Please don't try to use your finger nails to pry or lift the panels.
8.
Inside the case you should see the power supply, some wiring (LED's
etc.), an installed I/O panel, a power cord and a plastic bag containing
more hardware (screws, brass standoff, plastic stands, etc.).
Motherboard Installation
This manual is not designed to cover CPU or RAM or expansion card instal-
lation. Please consult your motherboard manual for specific mounting
instructions and trouble-shooting.
1.
Lay the case down so that the open side is up. You should be able to
see the drive cage, and power supply.
2.
Make sure you have the appropriate I/O panel for your mother
board. If the panel provided is not suitable for your mother board
you should contact your motherboard manufacturer to set the
right I/O panel.
3.
Line up motherboard with standoff holes, and determine which ones
line up and remember where they are. (Note: Not all motherboards
will match with all of the provided screw holes, and this is not neces-
sary for proper functionality. In other words there will likely be extra
holes.)
4.
Lift up and remove your motherboard.
5.
Screw in the brass standoffs to the threaded holes that line up with
your motherboard.
6.
Place your motherboard on the brass standoffs.
7.
Screw in your motherboard to the standoffs with the provided metallic
Phillips head screws.
8.
Your motherboard is now installed into the case.
Power Connections
ATX power supplies have a single 20-pin (single large) power connector to the
motherboard. This is set up as a double row of 10 pins.
1.
Connect the 20-pin ATX power connector to your mother board. LED's
and Front panel Leads.
2.
Reset (labeled RESET SW) connects to your motherboard at the RST
connector. The label should be facing the front of the case, and for all
of the following connectors as well.
3.
Power LED (labeled POWER LED) connector is located behind the
Reset connector.
4.
Power Switch (labeled POWER SW) connects to the PWR connector
on the motherboard.
5.
Speaker (labeled SPEAKER) connector is behind the PWR connector.
6.
Hard Drive LED (labeled HDD.LED) connects to the IDE connector.
3.5" Device Installation
1.
Fasten your 3.5" floppy drive into the top drive bay with the
screws provided.
2.
Find a small 4-pin white connector on the power supply and connect it
into the male 4-pin connector on the floppy drive.
3.
Install your other 3.5" devices to the drive bays accordingly.
4.
Connect a 4-pin large white connector from the power supply to
the male 4-pin connector on each of the devices.
5.25" Device Installation
1.
Looking from the rear of the case you can see some metal grills.
Carefully use a screw driver through the metal grill and gently push
the plastic drive bay outwards until it comes off.
2.
Use your hands to twist the metal plate back and forth until it
breaks off.
3.
Fasten your 5.25" device into the drive bay with screws provided.
4.
Repeat the same procedure for other devices.
5.
Connect a 4-pin large white connector from the power supply to the
male 4-pin connector on each of the devices.
IDE Cable Connection
This is for IDE devices only.
1.
After you have connected the devices to the power supply, you
need to connect the IDE cables between the devices and the
motherboard.
2.
For hard drives and CD ROMs use the 40-pin IDE ribbon cables. For floppy
drives use the 34-pin IDE ribbon cables. These should come with your
devices and have a red strip on side. When you connect a ribbon cable to a
device make sure that the red strip is toward the power connector.
Advertisement
