GE Monogram ZDIS15 Design And Installation Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Ice Maker
  5. Monogram ZDIS15
  6. Design and installation manual
GE Monogram ZDIS15 Design And Installation Manual

GE Monogram ZDIS15 Design And Installation Manual

Automatic icemaker
Hide thumbs Also See for Monogram ZDIS15:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Instruction and Installation Manual
Installation
Instructions
Automatic Icemaker
ZDI15
ZDIS15
Design Guide with
Installation Instructions
Monogram:_

Advertisement

Table of Contents
loading

Related Manuals for GE Monogram ZDIS15

Summary of Contents for GE Monogram ZDIS15

  • Page 1 Installation Instructions Automatic Icemaker ZDI15 ZDIS15 Design Guide with Installation Instructions Monogram:_...

  • Page 2: Table Of Contents

    Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner's Manual for warranty information. • Use this appliance only for its intended purpose.

  • Page 3: Design Information

    3/4" panel. See installation instructions pages 9 and 10. TOOLS AND MATERIALS REQUIRED • 1/4" socket • 3/4" adjustable wrench •Level • GE SmartConnect Refrigerator Tubing Kit or 1/4" O.D. copper tubing, of sufficient length to reach the installation...

  • Page 4: Installation

    Installation Instructions ADVANCE PLANNING POWER SUPPLY IMPORTANT: (Please read carefully). CAUTION: Due to excessive weight, TWO PEOPLE ARE REQUIRED TO FOR PERSONAL SAFETY,THIS APPLIANCE MUST BE MOVE AND INSTALL THIS ICE MACHINE. PROPERLYGROUNDED. MISE EN GARDE : Do not use an extension cord or adapter plug with this appliance.

  • Page 5: Remove Packaging

    Installation Instructions REMOVE PACKAGING AND PARTS ADJUST HEIGHT OF ICE MACHINE • Lay the carton on rear face Height adjustments may be necessary to install and break open the bottom the ice machine below a countertop, and may be flap. accomplished by adjusting both the front and rear leveling legs, •...

  • Page 6: Water Supply

    Allow enough to from flowing back into accommodate moving unit forward for service. the ice machine storage NOTE: The only GE approved plastic tubing is supplied bin and potentially in the GE SmartConnect Refrigerator Tubing kits. Do /Drain Hose flowing onto the floor.

  • Page 7: Connect Water Supply

    • Remove the hinge pin from the top hinge. Icemaker • Lift the door off of the bottom hinge. Place the hinge GE SmartConnect Tubing: pin back into the top hinge. • Insert the molded end ofthe tubing into the icemaker connection.
  • Page 8 Installation Instructions REVERSE THE DOOR SWING (cont.) REVERSE THE DOOR SWING (cont.) To reverse the door catch: Reverse the hinges: • Using a flat putty knife, remove the screw hole plugs • Remove the plastic screws opposite the door hinges, top and bottom. Set aside. from the opposite side of the door.
  • Page 9 Installation Instructions for ZIP75WW, ZIP75BB Kit BEFORE YOU BEGIN This kit contains a new handle and 2 side mounting brackets to support a trimless custom door panel up to 3/4"thick. A custom handle may replace the Read these instructions completely and supplied handle.
  • Page 10 Installation Instructions for ZIP75WW, ZIP75BB Kit STEP 5 SECURE SIDE TRIM PIECES TO THE ICE MACHINE TO CUSTOM PANEL I STEP 1 DISCONNECT POWER • Lay the custom panel appearance-side-down on a clean surface. STEP 2 REMOVE HANDLE • Align top and bottom side trim to the custom AND NAMEPLATE panel sides.
  • Page 11 Notes...
  • Page 12 NOTE: t ro(lucl improv(_m(_m is a comimfillg (md(_avor al G( neral El(_ctri(. Th(r(for(_, malerials, appearan(:( sul_je(:t to (h_mg¢ sp(_(ifi(alions ar(_ wilholll noli((. Monogram; Pub.No. 49-60016-3 ] PartNo. 197D2522PO01 GE Consumer & Industrial Louisville, KY40225 2217279Rev.1 02-04JR Printedin the United States @2004 GE Company...

Table of Contents