Crisper Humidity Control; Ice Maker; Water Dispenser - Jenn-Air Refrigerators User Instructions

Door Alarm
The Door Alarm feature sounds a chime every few seconds when
the refrigerator door has been left open for 5 continuous minutes.
The chime will sound until the door is closed or Door Alarm is
turned off.
Press the DOOR ALARM touch pad to turn this feature on or
off. The indicator light will be lit when the Door Alarm feature is
on.
Water Filter Status Light and Filter Reset
(on some models)
The Filter Reset control allows you to restart the water filter status
tracking feature each time you replace the water filter. See "Water
Filtration System."
Press and hold FILTER RESET for 3 seconds, until the Order
or Replace light turns off.
Digital Control User Preferences
The control center allows you to set user preferences, if desired.
Super Cool (CC)
This preference allows you to improve the airflow and temperature
control. To save energy, turn off this feature by pressing OFF.
Temperature Display (F_C)
This preference allows you to change the temperature display.
F - Temperature in degrees Fahrenheit
C - Temperature in degrees Celsius
Alarm (AL)
This preference allows you to turn off the sound of all alarms.
ON - You will hear the alarm sound.
OFF - You will not hear the alarm sound.
Auto Light Level Selection (LL)
This preference allows you to adjust the dispenser light level from
dimmest to brightest (settings 1 through 9).
NOTE: The Auto Light feature on the control center must be
selected to activate this preference.
Sabbath Mode (SAB)
ON - All control panel lights and alarm tones will be disabled.
OFF - All control panel lights and alarm tones will be enabled.
NOTE: Press the DOOR ALARM touch pad for 3 seconds to
restore all lights.
To Access the User Preferences Menu:
1. Press and hold the DOOR ALARM touch pad for 3 seconds.
The preference name will appear in the Freezer display and
the preference status (F or C) or (ON or OFF) will appear in the
Refrigerator display.
2. Use the Freezer (+) or (-) control to scroll through the
preference names. When the desired preference name is
displayed, press the Refrigerator (+) or (-) control to select the
preference status.
3. Set your preferences by pressing and holding the DOOR
ALARM touch pad for 3 seconds, or by shutting the
refrigerator compartment door.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed
crisper. Depending on your model, adjust the control to any
setting between FRUIT and VEGETABLES or LOW and HIGH.
FRUIT / LOW (open) for best storage of fruits and vegetables with
skins.
VEGETABLES / HIGH (closed) for best storage of fresh, leafy
vegetables.

Ice Maker

(on some models)
Turning the Ice Maker On/Off
To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.
Ice Production Rate
The ice maker should produce a complete batch of ice
approximately every 3 hours.
To increase ice production, lower the freezer and refrigerator
temperature. See "Using the Controls." Wait 24 hours
between adjustments.
Remember
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
Do not store anything on top of the ice maker or in the ice
storage bin.

Water Dispenser

(on some models)
IMPORTANT:
After connecting the refrigerator to a water source, flush the
water system. Press the button on the dispenser for
5 seconds, then release it for 5 seconds. Repeat until water
begins to flow. Once water begins to flow, continue
depressing and releasing the dispenser button (5 seconds on,
5 seconds off) for an additional 2 minutes. This will flush air
from the filter and water dispensing system. Additional
flushing may be required in some households. As air is cleared
from the system, water may spurt out of the dispenser.
13