Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
User's Information Manual
Models: 51 - 211
WARNING
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or
loss of life.
This appliance MUST NOT be installed in any location where
gasoline or flammable vapors are likely to be present.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your
building.
• Immediately call your gas supplier from a near by phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
Save this manual for future reference.
WBII-USER Rev D
Advertisement
Table of Contents
Related Manuals for Knight 51
Summary of Contents for Knight 51
- Page 1 WBII-USER Rev D User’s Information Manual Models: 51 - 211 WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. This appliance MUST NOT be installed in any location where gasoline or flammable vapors are likely to be present.
-
Page 2: Table Of Contents
Contents HAZARD DEFINITIONS ............. 2 3. OPERATING INSTRUCTIONS ........9 PLEASE READ BEFORE PROCEEDING ......3 4. SMART SYSTEM CONTROL MODULE 1. PREVENT COMBUSTION AIR CONTAMINATION ..4 SMART SYSTEM Control Module ........10 2. MAINTENANCE SCHEDULE ........5 Access Modes ............10 Maintenance Procedures ........... -
Page 3: Please Read Before Proceeding
User’s Information Manual Please read before proceeding Boiler service and maintenance – The Knight Wall Mount Installation and NOTICE Operation Manual along with the Knight • To avoid electric shock, disconnect electrical supply Wall Mount Service Manual are for use before performing maintenance. -
Page 4: Prevent Combustion Air Contamination
Areas likely to have contaminants Knight Wall Mount Installation and Operation Manual. Dry cleaning/laundry areas and establishments To prevent the potential of severe... -
Page 5: Maintenance Schedule
User’s Information Manual Maintenance schedule Owner maintenance Service technician (see pages 6 - 8 for detailed instructions) (see the Knight Wall Mount Service Manual) General: • Reported problems • Check boiler area Daily • Inspect interior; clean and vacuum if •... -
Page 6: Maintenance Procedures
User’s Information Manual Maintenance schedule Maintenance procedures Read the list of potential materials listed in Table 1A on page 4 of this manual. If any of these products are in the Boiler must be serviced and maintained room from which the boiler takes its combustion air, they must be removed immediately or the boiler combustion air (and vent termination) must be relocated to another The boiler must be inspected and started... - Page 7 3. Slope condensate tubing down and away from the boiler into a drain or condensate neutralizing filter. Condensate from the Knight wall mount boiler will be slightly acidic (typically with a pH from 3 to 5). Install a neutralizing filter if required by local codes. Call your...
-
Page 8: Check Air Vents
This discharge line must be installed by a qualified heating installer or service technician in accordance with the instructions in the Knight Wall Mount Installation and Operation Manual. The discharge line must be terminated so as to eliminate possibility of severe burns... -
Page 9: Operating Instructions
User’s Information Manual Operating instructions... -
Page 10: Smart System Control Module
Most parameters are available only to the installer, accessible the arrow (>) is pointing to “TIME & DATE”. Press the only by entering the installer password, see the Knight Boiler NAVIGATION dial once. If the date and time are incorrect, Service Manual. -
Page 11: Temperature Settings
User’s Information Manual SMART SYSTEM control module (continued) Night Setback Override Space heating (SH1, SH2, SH3) and tank set points Any Night Setback On trigger currently active or scheduled Mixing valves are required for the within the next seven (7) days can be skipped. To skip a CAUTION protection of any low temperature loops. -
Page 12: Status Display Screens
User’s Information Manual SMART SYSTEM control module Figure 4-2 Status Display Screen (CALL FOR (BOILER HEAT) STATUS) (OPERATIONAL INFORMATION) (RIGHT SELECT KEY) (LEFT SELECT KEY) (NAVIGATION DIAL) Status Display Screens Section Display Description The unit has not received a call for heat from a remote thermostat nor STANDBY has it received a call for heat from a DHW thermostat. - Page 13 User’s Information Manual SMART SYSTEM control module (continued) Status Display Screens (cont’d) Section Display Description SYSTEM: The temperature read by the system supply sensor (if connected). TANK: The temperature read by the tank sensor (if connected). OUTDOOR: The temperature read by the outdoor sensor (if connected). INLET TEMP: The temperature read at the inlet to the heat exchanger.
-
Page 14: Status Display Screens
User’s Information Manual SMART SYSTEM control module Status Display Screens (cont’d) Section Display Description Press and hold the LEFT SELECT key for 5 seconds to enter the Menu MENU Screen. EXIT Press the LEFT SELECT key to exit the current screen or setting. Press the LEFT SELECT key to confirm that the boiler needs to shutdown. -
Page 15: Notes
User’s Information Manual Notes... -
Page 16: Revision Notes
Revision Notes: Revision A (ECO C05747) initial release. Reflects the new model numbers for the Knight Wall Mount upgrade. Revision B (ECO C07072) reflects the change in design of the manual air vent and the update of FIG. 2-3 on page 8.
Need help?
Do you have a question about the 51 and is the answer not in the manual?
Questions and answers