Page 1
NOTE: Please read all instructions carefully before using this product Safety Notice MARCY SMITH MACHINE Hardware Identifier SM 2000 Assembly Instruction Parts List Warranty Ordering Parts Model SM 2000 Retain This Manual for Reference 07-30-01 OWNER'S IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746...
ORDERING PARTS..................………… 14 BEFORE YOU BEGIN Thank you for selecting the MARCY SMITH MACHINE SM 2000 by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Main Base Frame (#3) to both Left & Right Base Frames (#1) & (#2). Secure them with one Bracket (#7), two M10 x 3”...
Page 6
STEP 2 (See Diagram 2) A.) Slide the two Safety Catches (#12) onto the two Front Vertical Beams (#9) and the Guide Rods (#16). Push them down to the selected hole on the Front Vertical Beams and insert a Lock Knob (#15) to obtain the desired height for each Catch. B.) Slide two Rubber Bumpers (#14) onto each of the Guide Rods (#16).
Page 7
STEP 3 (See Diagram 3) A.) Insert the Rear Vertical Beam (#23) into the opening on the Rear Stabilizer (#10). Secure it with two M10 x 2 ½” Allen Bolts (#22), four ¾” Washers (#5), and two M10 Aircraft Nuts (#6). B.) Slide the Weight Holder (#31) onto the Rear Vertical Beam (#23).
Page 8
STEP 4 (See Diagram 4) A.) Attach the Upper Frame (#21) to the top of Front Top Beam (#19), Middle Vertical Beam (#8), and Rear Vertical Beam (#23). B.) Secure the Upper Frame (#21) to the Rear Vertical Beam (#23) with two M10 x 2 ½” Allen Bolts (#22), four ¾”...
Page 9
STEP 5 (See Diagram 5) A.) Attach the Butterfly Bracket (#43) to the Middle Vertical Beam (#8). Secure it with one Bracket (#48), two M10 x 3” Allen Bolt (#4), four ¾” Washers (#5), and two M10 Aircraft Nuts (#6). B.) Attach the Left Butterfly (#39) to the Butterfly Bracket.
Page 10
STEP 6 (See Diagram 6) A.) Insert one end of the Butterfly Cable (#65) through the hole on the Left Butterfly (#39). Attach a Cable End Clip (#47) to the Cable. Pull the Cable towards the back of the machine to secure the end. B.) Draw the Cable to the Butterfly Bracket behind the Vertical Beam (#8).
Page 11
STEP 7 (See Diagram 7) A.) Attach the Upper Cable (#25) to the open bracket at the front of the Upper Frame (#21). Install a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#24), two ¾”...
PARTS LIST KEY NO. DESCRIPTION Q’ty Left Base Frame Backrest Board Right Base Frame M8 x 2 ½” Allen Bolt Main Base Frame 4’ Chrome Bar Sleeve M10 x 3” Allen Bolt 3” Rubber Bumper ¾” Washer M8 x 5/8” Allen Bolt M10 Aircraft Nut 7’...
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.