Page 1
NOTE: Please read all instructions carefully before using this product Table of Contents POWERHOUSE Safety Notice SMITH MACHINE Hardware Identifier SM 3000 Assembly Instruction Parts List Warranty Ordering Parts Model SM 3000 Retain This Manual for Reference 06-24-02 OWNER'S IMPEX FITNESS PRODUCTS MANUAL 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746...
TABLE OF CONTENTS BEFORE YOU BEGIN..................IMPORTANT SAFETY NOTICES..............HARDWARE IDENTIFIER..…..............…. SMITH MACHINE ASSEMBLY INSTRUCTIONS..........EXPLODED DIAGRAM…………………………………………………………….. SMITH MACHINE PARTS LIST………..………………………………………….. MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS....... EXPLODED DIAGRAM……………………………………………………………... 20 MULTI-PURPOSE BENCH PARTS LIST…………………………………………. 21 WARRANTY....................…. 22 ORDERING PARTS..................… 22 BEFORE YOU BEGIN Thank you for selecting the POWERHOUSE SM3000 by IMPEX FITNESS PRODUCTS.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Rear Base Frame (#3) to the Left Base Frame (#1). Secure it with two M10 x 3”...
Page 6
STEP 2 (See Diagram 2) A.) Slide the Safety Stop Frame (#12) onto the Front Vertical Beam (#9) and Guide Rod (#16) from the top. Drop the Stop Frame all the way down. Align the hole and secure it with a Quick Release Knob (#15). Slide the Rubber Bumper (#14) onto the Guide Rod (#16).
Page 7
STEP 3 (See Diagram 3) A.) Attach the Lat Bar Frame (#23) to the Lat Bar Base (#10). Secure it with two M10 x 2 ½” Allen Bolts (#22), four ¾” Washers (#5), and two M10 Aircraft Nuts (#6). B.) Slide the Weight Post (#31) onto the Lat Bar Frame (#23). C.) Slide two Rubber Bumpers (#54) onto the weight posts.
Page 8
STEP 4 (See Diagram 4) A.) Attach the Upper Frame (#21) to the top of the Front Top Beam (#19). Secure it with one M10 x 3” Allen Bolt (#4), two ¾” Washers (#5) and one M10 Aircraft Nut (#6). B.) Attach the back of the Upper Frame (#21) to the top of the Lat Bar Frame (#23).
Page 9
STEP 5 (See Diagram 5) A.) Attach the Backrest Board (#51) to the Rear Vertical Beam (#8). Secure it with two M8 x 2 ½” Allen Bolts (#52) and 5/8” Washers (#35). B.) Attach the Butterfly Support (#43) and the Butterfly Pulley Support (#48) to the Rear Vertical Beam (#8).
Page 10
STEP 6 (See Diagram 6) A.) Attach one end of the 77” Butterfly Cable (#65) to the Right Butterfly Arm. Secure it with a M10 x 1” Allen Bolt (#32), two ¾” Washer (#5), and M10 Aircraft Nut (#6). Do not over tighten the nut and bolt. Let the Cable eyelet pivots on the bolt. B.) Draw the Cable to the Butterfly Pulley Support (#48).
Page 11
STEP 7 (See Diagram 7) A.) Attach the 132” Upper Cable (#25) to the top of the Upper Frame (#21). Make sure the ball on the Cable is underneath the Frame. Attach a Pulley (#38) to the bracket then secure it with one M10 x 1 ¾” Allen Bolt (#24), two ¾”...
PARTS LIST KEY NO. DESCRIPTION Q’ty Left Base Frame Butterfly Backrest Boar Right Base Frame M8 x 2 ½” Allen Bolt Rear Base Frame Lifting Sleeve M10 x 3” Allen Bolt 3” Thick Rubber Bumper ¾” Washer M8 x ½” Allen Bolt M10 Aircraft Nut Wight Bar Bracket...
MULTIPURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front Stabilizer (#2). Align the holes and secure it with three M10 x 5/8”...
Page 16
STEP 2 (See Diagram 2) A.) Attach two Bushings (#23) to each Seat Support Frames (#6). B.) Attach one Backrest Support (#7) to the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 5/8” Allen Bolt (#32), and one ¾”...
Page 17
STEP 3 (See Diagram 3) A.) Align the holes on the two Backrest Supports (#7) to the pivot on the Sliding Block (#9). Secure them with one M10 x 6 ¼” Allen Bolt (#35), two ¾” Washers (#39), and one M10 Aircraft Nut (#41). DIAGRAM 3...
Page 18
STEP 4 (See Diagram 4) A.) Attach the Seat Incline Support Bracket (#8) to the Main Frame (#1). Secure it with one M10 x 4 3/4” Allen Bolt (#34), two 3/4” Washers (#39), and one M10 Aircraft Nut (#41). Do not over tighten the nut and bolt. The Bracket needs to be able to swivel.
Page 19
STEP 5 (See Diagram 5) A.) Place the Seat Pad (#14) onto the Seat Support Frames (#6). Align the holes and secure it with four M8 x 2” Allen Bolts (#37) and 5/8” Washers (#40). B.) Place the Backrest Board (#15) onto the Backrest Supports (#7). Align the holes and secure it with four M8 x 2”...
Page 20
STEP 6 (See Diagram 6) A.) Insert the Leg Developer Holder (#4) into the opening in front of the Seat. Secure it with a Lock Knob underneath the Seat. Attach the Leg Developer (#5) to the bracket on the Leg Developer Holder (#4). Secure it with an Axle (#12), two ¾”...
MULTIPURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty Main Frame Front Stabilizer Rear Stabilizer Leg Developer Holder Leg Developer Seat Support Frame Backrest Support Seat Incline Support Bracket Sliding Block Incline Adjustment Bar Foam Tube Axle Olympic Sleeve Seat Pad Backrest Pad Leg Developer Bushing Arm Curl Stand...
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.