Summary of Contents for Impex PLATINUM MARCY PM-9150
Page 1
NOTE: Please read all instructions carefully before using this product PLATINUM MARCY Table of Contents POWER SYSTEM Safety Notice Hardware Identifier PM-9150 Assembly Instruction Parts List Warranty Ordering Parts Model PM-9150 Retain This Manual for Reference 08-11-08 OWNER'S MANUAL ®...
MULTI-PURPOSE BENCH PARTS LIST………………………………………… 23 WARRANTY....................… 24 ORDERING PARTS..................24 BEFORE YOU BEGIN Thank you for selecting the PLATINUM MARCY PM-9150 POWER SYSTEM by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
WARNING LABEL PLACEMENT The warning labels have been placed on the unit in location shown. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
FUNCTIONAL TRAINER ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Crossing Wrench and Allen Wrenches. NOTE: Two or more people assembling this machine is a must. Do NOT attempt to assemble this machine alone. STEP 1 (See Diagram 1) A.) Do not tighten the Nuts and Bolts until instructed to so. B.) Place the Lower Cross Brace (#4) between the Right &...
Page 8
STEP 2 (See Diagram 2) A.) Lift up the Selector Stem (#19) on the Right Station (#1) and hold it still to release the tension on the cables. Remove the two M10 x ¾” Allen Bolts (#67), Ø ¾” Spring Washers (#74), and Ø...
Page 10
STEP 3 (See Diagram 3) A.) Slide a Plastic Washer (#106) onto the axle on Upper Hanger Bracket (#92). Insert the axle through the Upper Cross Brace (#83) from bottom. Secure it with one M8 x ½” Allen Bolt (#80), one Ø 7/8” Washer (#81), and one D-shaped Washer (#90).
Page 11
STEP 4 (See Diagram 4) A.) Peel off the cover paper on the surface of the Right Outer Cover (#32) and Right Inner Cover (#34). B.) Attach the Right Outer Cover to the Right Station from the outside. Note: Make sure the two round holes on the Cover need to attach to the top of the Station.
Page 12
STEP 5 (See Diagram 5) A.) Pull down one Chin-up Pull Pin (#98). Insert one Chin-up Handle into the hole on Upper Frame (#3), and then release the Pull Pin to secure the Handle. Repeat the same procedure to install the other Chin-up Handle. B.) Attach one Exercise Chart Hanger Bracket (#15) to the Right Station (#1).
Page 13
STEP 6 (See Diagram 6) A.) Attach the Height Adjustment Handle (#36) to the Right Lock Switch (#10) on the Pulley Carriage (#8). Secure it with one M5 x 3/8” Allen Bolt (#71). Repeat the same procedure to install the other side. B.) Connect the Single Handle (#31) to the Cable (#17) on the Right Station (#1) with a Hook (#54).
E.) Store Curl Bar (#86), Straight Bar (#87), Rope (#101) onto the Upper and Lower Hanger Bracket (#92) & (#93). DIAGRAM 6 WEIGHT RESISTANCE CHART Plate Label 17.5 20.0 22.5...
Page 15
25.0 27.5 30.0 32.5 35.0 37.5 *Numbers are approximate, actual value may vary.
PARTS LIST KEY NO. DESCRIPTION Q’ty Right Station Ø 1” Clip Left Station Ø 5/8” Clip Upper Frame Ø 1” Washer Lower Cross Brace Ø ¾” Washer Chrome Slide Tube M10 x 5 1/8” Allen Bolt Right Carriage Support Frame M10 x 3”...
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: One Adjustable Wrench and Allen Wrenches. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Seat Support (#9) onto the Front Post (#8). B.) Secure it with two M10 x 3 ¾”...
Page 20
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#9) onto the Rear Stabilizer (#13). B.) Secure it with two M10 x 3 ¾” Allen Bolts (#29), four Ø ¾” Washers (#3), and two M10 Aircraft Nuts (#28). C.) Securely tighten all Nuts and Bolts installed.
Page 21
STEP 3 (See Diagram 3) A.) Insert the Foam Tube (#15) halfway through the hole on the Front Post (#8). B.) Push two Foam Rolls (#27) onto the Tube from both ends. Plug two Foam Roll End Caps (#1) into the ends. DIAGRAM 3...
Page 22
STEP 4 (See Diagram 4) A.) Place the Seat Pad (#19) onto the Left & Right Seat Brackets (#16 & #17). B.) Secure it with four M8 x ¾” Allen Bolts (#36) and Ø 5/8” Washers (#6). DIAGRAM 4...
Page 23
STEP 5 (See Diagram 5) A.) Attach the Backrest Board (#18) to the Backrest Support (#10). B.) Secure it with three M8 x 2 5/8” Allen Bolts (#37) and Ø 5/8” Washers (#6). C.) When adjusting the Backrest Board to an incline position, simply pull up the Board. When adjusting the Board to decline or flat positions, press or step down on the Backrest Adjustment Lever (#14) to disengage the Lever to allow the Board to go down.
MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty Foam Roll End Cap Wheel Ø ¾” Washer Ø 1” Washer Ø 1 3/8” Washer Ø 5/8” Washer Ø 1” Bushing Front Post Main Seat Support Backrest Support Backrest Incline Support Seat Incline Support Rear Stabilizer Backrest Adjustment Lever Foam Tube...
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.