Remote Control; Placing The Television In Standby Mode - Samsung CS29Z47 Owner's Instructions Manual

Remote Control

(depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
TV CH LIST EZ.VIEW SRS
PIP INFO TTX/MIX
P.MODE S.MODE STILL P.SIZE
SOURCE SWAP SIZE
DUAL TURBO POSITION P
1 POWER 3 -/--
Used to switch the TV on Used to select a channel
and off. numbered ten or over.
Press this button, then
2 Numeric buttons
"--" symbol is displayed.
Used to select channels
Enter the two-digit chan-
directly.
nel number.
4 CH LIST
5 TV
Used to return to the
TV mode when it is in
external input mode.
/
6
Used to increase or
decrease the volume.
7 MENU
Used to display the on-
screen menu or return to
the previous menu.
8 ▲/▼/◄/►
Used to control the cur-
sor in the menu.
9 INFO
Used to view the channel
information and setting
status you selected.
21 0 PIP
! S.MODE
Used to select the sound
effect.
22
@ P.MODE
23
Used to select the pic-
ture effect.
# SOURCE
$ DUAL
% SWAP
24
25
^ TURBO
Used to select the turbo
26
sound option.
& SOURCE
27
Used to display all of the
28
available video sources.
Installing Batteries
Remove the cover. Install two AAA size
batteries, then replace the cover.
When the remote control does not
operate normally, check that the "+"
and "–" ends of the batteries are
inserted correctly or the batteries are
drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
* PRE-CH
Used to switch repeat-
edly between the last
2
two channels displayed.
1
( EZ.VIEW
Used to display Chan-
nel Grouping, Channel
Minimizer, Channel
Schedule, Music Mode,
Half Mute menu.
) SRS
/
a P
Used to display the next
or previous stored
channel.
b EXIT
Used to exit from any
display or return to
normal viewing.
c MUTE
Used to switch the sound
off temporarily. To turn
the sound back on, press
the MUTE, , or
button.
d STILL
e P.SIZE
/
f P
Used to display the next
or previous stored
channel.
g SIZE
h P OSITION
English - 
Switching the Television On and Off
The mains lead is attached to the rear of the television.
 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
 Press the "I" button (On/Off) on the front (or side) of the
television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to "Channel - Auto Store" on page 3 or "Channel
- Manual Store" on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
"Setup - Plug & Play" on page 3.
4 To switch the television off, press the "I" button (On/Off)
on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
The television is in standby mode.
 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the "I"
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.