Opticom Technologies Inc. “L” Series DVR SAFETY PRECAUTIONS The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance The Lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage"...
Opticom Technologies Inc. “L” Series DVR Table of Contents 1. About the User’s Guide 2. Introduction 3. Equipment Setup Related H/W 3.1 Unpacking (Board Type) 3.1.1 System Requirement 3.1.2 Package Content Per Model 3.1.3 Chipset Comparability 3.2 Unpacking (PC Base System) 3.3 Front of the DVR System...
Page 4
10.3 Audio Setting 10.4 Analog Video Out Setting 10.5 Sensor & Link Alarm Setting 10.6 Alarm Setting 10.7 Alarm Wave File Setting 11. Video Channel Configuration 11.1 Motion Detection Setting 11.2 PTZ Configuration 11.3 Camera Configuration Setting 11.4 Video Adjust 11.5 Video Quality 11.6 Alarm Sound &...
24. Customer’s Responsibilities 25. Manufacturer’s Responsibilities 26. Safety Summary Opticom Technologies Inc. “L” Series DVR 1. About the User’s Guide This User’s Guide is designed for end users, installers and technical support. ● End User : If a user is able to perform basic operations or has basic knowledge about computers, he/she can understand and use most of the functionality of the DVR by simply following the instructions in this User’s Guide.
Opticom Technologies Inc. “L” Series DVR 2. Introduction The Vista “L” Series DVR series is an advanced digital video monitoring and recording system that converts analog video signals into digital data, displays the digital video on computer monitors in real time, stores it onto permanent storage such as hard disks with high compression ratio, and transmits it through the Internet.
Page 7
Opticom Technologies Inc. “L” Series DVR ● Rapid and flexible customization capability and high compatibility with analog CCTV systems. -Object-oriented programming and component software technology enable rapid completely reflecting customer requirements. -High compatibility with analog CCTV systems promotes the reuse of existing analog CCTV equipment.
Opticom Technologies Inc. “L” Series DVR 3. Harware Setup .11 Unpacking (Board Type) 3.1.1 System Requirements Minimum Requirement Recommended Intel Celeron 1.7 GHz equivalent Intel P-4 1.8 GHz or faster Windows 2000 series, Windows XP series Memory 128 MB 256MB or more...
Page 9
Opticom Technologies Inc. “L” Series DVR 3.2 Unpacking (System Type) DVR Main System Handles Application CD Keyboard Power Cable Manual Mouse Computer Case Keys...
Opticom Technologies Inc. “L” Series DVR 3.3 Front of the DVR System 1) Power LED: Indicates if the power is ON?OFF. 2) Run LED: Displays the status of the system. 3) HDD(Hard Disk Drive) LED: A lamp indicating the operation of the HDD 4) Power Switch: Turns the DVR system on or off.
Alarm Out Connector Parallel Port Audio Input Connector Video Connector Opticom Technologies Inc. “L” Series DVR Power Plug Lan Connection 3.5 Before You Start Make sure you have access to three standard grounded outlets and a flat level surface to support the main system.
Page 12
4. Video monitor cable to the main system Connect the video monitor cable to the main system by inserting one end of the 9-pinconnecting cable into the back of the main system. 5. Video monitor cable to video monitor Connect the video monitor cable to the video monitor by inserting one end of the 9-pin connecting cable into the back of the video monitor.
Vista “L” Series DVR. Wait a few moments for the display to appear. The system performs a self-test and displays a message if any errors are found. Call the OPTICOM TECHNOLOGIES Technical Support.
Opticom Technologies Inc. “L” Series DVR 5. Current Time Setting Vista “L” Series Because the DVR System is using the Windows system time, the time already set at the factory needs to be set again with the appropriate time according to the user’s geographic location.
Page 15
Opticom Technologies Inc. “L” Series DVR Step 3) “Data Storage Setup” Button Click...
Opticom Technologies Inc. “L” Series DVR 6. Program Start Step 1) In the Windows main screen, click “Start” → “Programs → Vista “L” Series DVR “ ” Click Step 2) Auto Update Step 3) Main Screen...
Opticom Technologies Inc. “L” Series DVR 7. Storage Configuration : Add or delete allocation space of the hard drive for recorded video data. * Available Hard * Total Hard Drive Space * Used Hard Drive * To overwrite hard disk drive, check this box.
Page 18
Opticom Technologies Inc. “L” Series DVR 7.1 Select Hard Drive Space for Recording...
Page 19
Opticom Technologies Inc. “L” Series DVR Step 1) Click Setting Button...
Opticom Technologies Inc. “L” Series DVR 8.2 Main Buttons Click to search recorded video data. There are two types Video Search of search: general search and detailed search. Setup Click to setup the Vista L Series DVR. There are 6 types of system settings.
Opticom Technologies Inc. “L” Series DVR 8.3 Current Time and Status Display Current Time and Date Current time and date should be setup correctly for accurate video recording. The playback of the video is performed according to this time and date.
Page 23
Opticom Technologies Inc. “L” Series DVR 8.4 Split Screen Buttons The selected split screen icon is green. According to the DVR model, available screen split modes are as follows: Equally Split Screen Focused Split Screen Alternating Display and Full Screen Display...
Opticom Technologies Inc. “L” Series DVR 8.5 Camera Selection/Status Buttons In surveillance mode, each button corresponds to a camera. Clicking the camera button will display the corresponding camera in the main view. In Playback and Search Mode, select a camera for detailed search.
Opticom Technologies Inc. “L” Series DVR 8.6 Sensor/Control Status Buttons Displays the sensor input status and control output. The light is on when the sensor input is activated. Active Sensor Input The light is on when the control is activated. Active Control Output...
Opticom Technologies Inc. “L” Series DVR 10.1 Video Source & E-mail Setup * Sensor or Motion triggered channel pops up in a large screen. Adjust for length of time in seconds.
Page 29
Opticom Technologies Inc. “L” Series DVR *Windows Sound and Audio Devices Properties open up. Click “OK” to exit.
Opticom Technologies Inc. “L” Series DVR 10.4 Analog Video Out Setting * Analog Video out Rotation Interval * Select cameras to view through analog video out. -Default : Select all cameras -Reset : Unselect all cameras 10.5 Sensor & Link Alarm Setting Connect up to 8 sensors.
Opticom Technologies Inc. “L” Series DVR 10.6 Alarm Setting Connect up to 8 alarms. Name individual alarms. Select duration of the alarm. (1 ~ 180 seconds) 10.7 Alarm Wave File Setting Select wave file to be played for motion detection.
Opticom Technologies Inc. “L” Series DVR 11. Video Channel Configuration : Settings for Motion Detect, Recording Quality, Camera Display, PTZ, Alarm Sound and E-mail. * Click “ALL” button to select or un-select all cameras.
Opticom Technologies Inc. “L” Series DVR 11.1 Motion Detection Setting Current view of selected camera. Set motion detection sensitivity and region. Motion detection region application size. (PEN size: PEN1 < PEN2 < PEN3) Show/Hide motion detection region on the view screen.
Opticom Technologies Inc. “L” Series DVR 12. Recording Schedule Configuration Setup recording schedule, recording frame rate, pre-alarm and post alarm. * Click “ALL” button to select or un-select all cameras.
Opticom Technologies Inc. “L” Series DVR 12.1 Pre-Post Alarm Recording Time Setting * When Motion or Sensor recording is selected, pre-alarm and post-alarm recording is possible up to 5 seconds. Pre-Post Alarm applies to all the cameras regardless of recording schedule.
Page 38
Opticom Technologies Inc. “L” Series DVR Sensor connected to the cameras. If external light is attached to the camera, the light will be powered on selected camera and timeframe. Alarm Sound and Email notification will operate when motion or Sensor is detected.
Page 39
Opticom Technologies Inc. “L” Series DVR...
Opticom Technologies Inc. “L” Series DVR 13.1 Server Configuration .* Server Name, IP Address, Client Video Transmission Quality configuration. Enter DVR Server name. Open “Network Connections” (View page 46 for more info. ) Current IP address Enable Web browse client TCP Service can be any number Between 1200 and 9999.
Page 45
Opticom Technologies Inc. “L” Series DVR Open “Network Connections” window to configure network. Step 1) Right click on Local Area Connection Step 3) Fill in appropriate values in the And click “Properties”. following window. Click “OK” Step 2) Select “Internet Protocol (TCP/IP)” and click “Properties”...
Opticom Technologies Inc. “L” Series DVR 13.2 User Registration * Enter ID and Password for Client to connect to Server. Enter User Id. Enter Username. Enter Password. Select User Level. Live monitoring. Live monitoring and playback. Live monitoring, playback and configuration.
Opticom Technologies Inc. “L” Series DVR 15.1 PTZ Button Description Pan / Tilt control button : A button to control the direction of the camera ( Up, Down, Left and Right) Image Zooming in/out control button: Used to zoom in and out of selected image Focus Control button: Used to control the focus of the selected camera.
Opticom Technologies Inc. “L” Series DVR 16.1 Calendar & Playback Calendar Select the Year and month of interest, then the color coded dates are shown. limited to the range you selected earlier. Play: Play the selected video Fast Play: Fast forward play the selected video Next Image: Go to next image frame.
Page 53
Opticom Technologies Inc. “L” Series DVR 16.2 Recorded Data Search Window Example Display the selected date Denotes camera number * Video recording status map shows the video recording status; the column denotes channels and the row denotes the time. One row represents a 30 minute time slot. You can select time-camera zones by using the keyboard or dragging the mouse.
Opticom Technologies Inc. “L” Series DVR 17.2 Digital Zoom In/Out and Image Enhancement Restore: The image is restored to its original state. All the zooming and moving actions are rolled back. Zoom In/Out: With the zoom in/out icon selected, place the cursor on the image region you want to zoom in on and drag it to the right.
Opticom Technologies Inc. “L” Series DVR 17.3 Still Image Print & Save Preview Selected Image: Preview the selected image. Here, you can set up the print layout [ 1x2 Layout] [ 2x4 Layout] [ 4x8 Layout] Selected Print: Print the selected image.
Page 57
Opticom Technologies Inc. “L” Series DVR Save selected image: Save the selected image onto a disk. Show/Hide Thumbnail Image: Show or hide the thumbnail images on the screen...
Opticom Technologies Inc. “L” Series DVR 19. Video Clip Backup * Year, Month and Date : * Channel Select : Select the date of the video Select the channel of the video on on which a video clip is made.
Opticom Technologies Inc. “L” Series DVR 21. Remote Monitoring 21.1 Starting Client Program Step 1) “My Computer” double click “C:/OpticomtechDVRs/OpticomTechdvrs.exe”...
Page 63
Opticom Technologies Inc. “L” Series DVR Step 4) Following window will open once password is entered.
Page 64
Opticom Technologies Inc. “L” Series DVR Step 5) Enter Server information to the screen below and click “ADD”. Click on Exit Button at the bottom to exit. Setup 6) Click Connect Button to connect.
Page 65
Opticom Technologies Inc. “L” Series DVR Step 7) Enter User ID and Password and click “CONNECT” to start Client program.
Page 66
Opticom Technologies Inc. “L” Series DVR 21.2 Client Features 21.2.1 Main Client Screen Description...
Opticom Technologies Inc. “L” Series DVR 23. Trouble Shooting Guide 1) ‘No Video Signal’ message on the screen. -Check camera input connector. -Check camera power supply. * Contact camera supplier for further troubleshooting. 2) Frozen Screen or screen shake in black and white.
Page 72
Opticom Technologies Inc. “L” Series DVR 5) Sensor malfunction. -Check for secure sensor connection at the sensor input. -Check power supply to sensor. -Check if that particular sensor is enabled in the setting. -Check if sensor type is entered correctly.
Page 73
Opticom Technologies Inc. “L” Series DVR 9) Motion detection malfunction. -Check if motion detection region is set for that particular camera. –Motion detection region setting instruction * Select desired PEN size and hold down mouse button and ‘paint’ desired area. (Set 0 –...
Page 74
Opticom Technologies Inc. “L” Series DVR 13) No recording. -Check schedule for desired recording schedule. -Recording schedule setting instruction. * Continuous Recording: Continuous recording during selected day and time. * Motion Detection Recording: Recording only when motion is detected during selected day and time.
Page 75
Opticom Technologies Inc. “L” Series DVR 18) Choppy playback. -Increase frame rate in the Recording Schedule. (Increasing the frame rate decreases the total recording time. Check required frame rate and total recording time and adjust appropriately.) 19) No display screen rotation even when the rotation time is set.
Page 76
Opticom Technologies Inc. “L” Series DVR 22) PTZ control malfunction. -Check for secure connection of the PTZ camera. -Check for correct controller connection. -Check for correct PTZ controller type and protocol. -Check for correct COM port selection for that particular PTZ controller.
Page 77
Opticom Technologies Inc 25. Manufacturer’s Responsibility Opticom Technologies Inc or its authorized representative is responsible for the effects on safety, reliability and performance of Vista “L” Series DVR only if: Repairs or modifications to Opticom Technologies Inc.are made by OPTICOM TECH authorized personnel.
Page 78
Opticom Technologies Inc. “L” Series DVR 26. Safety Summary Two labels are used in this manual to identify potentially dangerous conditions or procedures. WARNING and CAUTION messages must be strictly observed. WARNING identifies conditions or practices that may present danger to the user.
Page 79
To avoid electric shock, always dry your hands before plugging or unplugging Opticom Technologies Inc. “L” Series DVR 2) Always keep the DVR off the foreign objects. 3) Any modifications such as changing the HDD , installation of modem, etc. will be recommended to be serviced through OPTICOM TECH Co.,Ltd or any authorized branch...
Page 80
2) To prevent any instability. Do not drop or place materials such as heavy objects, liquids, high voltage materials, etc. The HDD is weak in taking shock. 3) Installation of DVR must be made by OPTICOM TECHNOLOGIES INC.or the authorized agents.
Page 81
and/or authorized agents with any questions...