Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DSPM Eternalight 1
Summary of Contents for DSPM Eternalight 1
- Page 1 D S P M Inc. User’s Manual Eternalight 1 Uninterruptible Power System Technical Manual #018-0056-03 Revision G Phone: (714) 970-2304 Fax: (714) 970-6171 Service: (714) 970-2304 (m-f, 8:00 – 5:00), after hours (951) 840-0811 Web Page: www.DSPManufacturing.com Email: sales@dspmanufacturing.com...
- Page 2 Congratulations on selecting one of the fine products from DSPM, the leader in power protection technology. Our wide product offering includes Uninterruptible Power Systems (UPS), Power Conditioners, Frequency Converters Specialty Transformers. Since our beginnings DSPM has shipped many of these fine products to discerning customers for use on sensitive equipment and critical loads.
- Page 3 DSPM employee or an employee of the recipient having a need to know, without the express written consent of DSPM, and further agrees to surrender this document to DSPM when the reason for its receipt has terminated.
-
Page 4: Important Safety Instructions
SAFETY Important Safety Instructions Save These Instructions This manual contains important instructions for the Eternalight 1 UPS System and should be followed during the installation, operation and maintenance of the UPS system. IMPORTANT SAFETY When using Electrical Equipment, basic safety precautions should always be followed,... -
Page 5: Battery Safety
It is strongly advised not to open the UPS cabinet as the components have very high voltages and touching them may be fatal. Only a technician from DSPM or a DSPM trained technician may service the unit. Phone: (714) 970-2304 Fax: (714) 970-6171 Service: (714) 970-2304 (m-f, 8:00 –... -
Page 6: Section 1- Operation
Upon restoration of input power, the UPS automatically resumes normal operation. Also the UPS immediately begins to recharge the batteries. The ETERNALIGHT 1 is a dual conversion single phase UPS available in output ratings of 2 to 80 kVA. The UPS is U.L. listed under UL1778 and/or UL924. The UPS is available with input voltages of 120, 208, 240 and 277 VAC;... - Page 7 1-2 BENEFITS The ETERNALIGHT 1 is designed to fit the needs for virtually all power conditioning and UPS applications. It has been specifically designed to power all forms of modern data processing, communications, process control equipment, lighting and emergency lighting equipment. The UPS does not require any derating as other UPS products may when powering 100% electronic loads including switch-mode power supplies.
- Page 8 Typical Front View, Doors Closed Phone: (714) 970-2304 Fax: (714) 970-6171 Service: (714) 970-2304 (m-f, 8:00 – 5:00), after hours (951) 840-0811 Web Page: www.DSPManufacturing.com Email: sales@dspmanufacturing.com...
- Page 9 (Typical left hand view) Phone: (714) 970-2304 Fax: (714) 970-6171 Service: (714) 970-2304 (m-f, 8:00 – 5:00), after hours (951) 840-0811 Web Page: www.DSPManufacturing.com Email: sales@dspmanufacturing.com...
- Page 10 (Typical right hand view) Phone: (714) 970-2304 Fax: (714) 970-6171 Service: (714) 970-2304 (m-f, 8:00 – 5:00), after hours (951) 840-0811 Web Page: www.DSPManufacturing.com Email: sales@dspmanufacturing.com...
-
Page 11: Product Features
1-3 PRODUCT FEATURES The following describes the major sub-systems within the ETERNALIGHT 1 UPS. INPUT AND OUTPUT FILTER – The input filter reduces the input transients and harmonics on the input line. This helps protect the electronic circuitry of the UPS. The output filter filters and noise and line spikes from loads. -
Page 12: Section 2 - Preinstallation
SECTION 2 – PREINSTALLATION 2-1 SITE PLANNING AND PREPARARTION The ETERNALIGHT 1 is designed for installation indoors where it is protected from the elements. The UPS can be installed in a variety of different environments including computer rooms, offices, and industrial/process control locations. For the best performance and reliability, temperature extremes should be avoided. - Page 13 Eternalight 1 Emergency Lighting Inverter Input Output Utility Feed Max Output Input Output Utility Feed Max Output KWatts KWatts Voltage Voltage Amps Amps Voltage Voltage Amps Amps 43.7 87.5 21.8 43.7 18.9 37.9 43.7 87.5 21.8 43.7 18.9 37.9 43.7 87.5...
-
Page 14: Section 3 - Installation
SECTION 3 – INSTALLATION The ETERNALIGHT 1 UPS system is shipped on a pallet with the batteries outside the UPS. This Manual, battery jumper wires and accessories may be included within the packaging, ensure that these are not discarded with the packaging. Unwrap the UPS and carefully inspect the external surfaces for abrasions, indentations, or other obvious damage. - Page 15 DANGER!! THE UPS CONTAINS POTENTIALLY LETHAL VOLTAGES INSIDE, EVEN IF THE UNIT IS NOT CONNECTED TO AN EXTERNAL SOURCE OF POWER. INSTALLATION SERVICE PROCEDURES SHOULD PERFORMED BY QUALIFIED PERSONNEL ONLY. The input power circuit is supplied by the customer. This provides power from the building source to the UPS system.
-
Page 16: Input Connections
Verify that the input voltage as stated on the UPS nameplate, matches the customer-supplied voltage. If the voltage does not match, STOP installation of the UPS and contact Customer Service at DSPM. Verify that Input cable and conduit are routed correctly and are in position to connect the unit. - Page 17 If the voltage does not match, or the intended applied load exceeds unit capacity, STOP installation of the UPS and contact Customer Service at DSPM. 2. Verify that Output cable(s) and conduit(s) are routed correctly and are in position to connect the unit.
- Page 18 Output Terminal Blocks Ground / Neutral / Hot 3-4 BATTERIES AND BATTERY CABLES WARNING!! FOLLOW THE BATTERY SAFETY PROCEDURE IN THE FRONT OF THIS MANUAL. The UPS system has fixed battery trays. All battery systems connect the batteries in series, i.e. plus terminal to minus terminal from one battery to another battery.
- Page 19 BATTERY SYSTEM TEST 1. Make sure A.C. input circuit breaker is OFF. 2. Make sure battery circuit breakers are OFF. 3. Use a meter and note the D.C. voltage at the battery circuit breaker. The voltage must be the correct polarity positive lead of the meter to the positive terminal of the circuit breaker.
-
Page 20: Starting The Ups
4-0 OPERATIONS 4-1 STARTING THE UPS 1. Check the input A.C. circuit breaker is OFF. 2. Check all output circuit breaker(s) (optional) are OFF. 3. Check the battery circuit breaker(s) are OFF. 4. Energize the Utility feeder to the unit. 5. - Page 21 History Log Key: The History Log is used to record certain events that reflect the status and operating mode of the unit. There are 64 lines (00 through 63). It is read by holding down the Alarm Scan button. Each time the button is pressed, the log is read sequentially with the most recent event being displayed first.
- Page 22 Ensure that the intended connected load does not exceed unit capacity. If the voltage does not match, or the intended applied load exceeds unit capacity, STOP installation of the UPS and contact Customer Service at DSPM. Phone: (714) 970-2304 Fax: (714) 970-6171 Service: (714) 970-2304 (m-f, 8:00 –...
-
Page 23: Output Power
UPS system is on battery power. These circuits usually power exits signs and lighting. 5.0 TECHNICAL SUPPORT 1. For Technical Support or any questions not covered in this manual, contact: DSPM Inc. 1921 South Quaker Ridge Place Ontario, CA 91761 714.970.2304 714.970.6171... -
Page 24: Maintenance
6.0 MAINTENANCE CAUTION: DO NOT DISPOSE OF BATTERIES IN FIRE CAUTION: DO NOT ATTEMPT TO OPEN THE BATTERIES CAUTION: THE FOLLOWING PRECAUTIONS SHOULD BE TAKEN WHEN REPLACING ANY BATTERIES • REMOVE WATCHES, RINGS, ETC… • USE TOOLS WITH INSULATED HANDLES. CAUTION: USE RUBBER PROTECTIVE GLOVES WHEN HANDLING DAMAGED BATTERIES. - Page 25 BATTERIES HAVE LEAD POSTS AND THEY ARE VERY EASY TO COMPRESS AND WILL CAUSE FAILURES IN THE FUTURE. Note: If Batteries are found to be leaking or fail the load test they should be replaced. (Consult DSPM as to the status of your Battery Warranty) 2. Annual CAUTION:...
-
Page 26: Troubleshooting
COMPRESS AND WILL CAUSE FAILURES IN THE FUTURE. Note: If Batteries are found to be leaking or fail the load test they should be replaced. (Consult DSPM as to the status of your Battery Warranty) 7.0 TROUBLE SHOOTING 7.0.1 If unable to resolve any problem please contact DSPM for assistance.
Need help?
Do you have a question about the Eternalight 1 and is the answer not in the manual?
Questions and answers