Eco Operation; Temporary Operation; Operation And Performance; Timer Operation - Carrier 42TVR010 Series Owner's Manual

ECO OPERATION

9
To automatically control room to save energy (except in DRY and FAN ONLY
mode)
Press : Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1 degree/
hour for 2 hour (maximum 2 degrees increase).
10

TEMPORARY OPERATION

In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or stop
without using the remote control
• Operation mode is set on AUTOMATIC operation,
preset temperature is 24°C and fan operation is
automatic speed.

TIMER OPERATION

11
Setting the ON Timer
1
Press : Set the desired ON timer.
ON
2
Press : Set the timer.
3
Press : Cancel the timer.
Everyday timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
1
ON
Press : Set the ON timer.
2
OFF
Press : Set the OFF timer.
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
12

PRESET OPERATION

Set your preferred operation for future use. The setting will be memorized by the
unit for future operation (except airfl ow direction).
1. Select your preferred operation.
for 3 seconds to memorize the setting. The P mark
2. Press and hold
displays.
3. Press : Operate the preset operation.

AUTO RESTART OPERATION

13
To automatically restart the conditioner after the power failure (Power of the unit
must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set the
operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)
• Do not operate ON timer and OFF timer.
2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the
operation. (3 beep sound but OPERATION lamp does not blink)

SLEEP TIMER OPERATION

14
To start the sleep timer (OFF timer) operation
Press : Select 1, 3, 5 or 9 hrs for OFF timer operation.
1110250108-EN.indd 3 1110250108-EN.indd 3
Setting the OFF Timer
Press OFF : Set the desired OFF timer.
Press : Set the timer.
Press : Cancel the timer.
3
Press .
4
Press button during the ( or )
mark fl ashing.
MAINTENANCE
15
Firstly, turn off the circuit breaker.
Filter Reset (Some models only)
FILTER lamp lights on; the fi lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
16

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated for 3
minutes when suddenly restarted or switched to ON.
2. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of
plastic.
Air conditioner operating conditions
Temp.
Outdoor Temperature
Operation
Cooling –10°C ~ 46°C
Dry –10°C ~ 46°C
TROUBLESHOOTING (CHECK POINT)
17
The unit does not operate.
• The power main switch is turned off.
• The circuit breaker is activated to
cut off the power supply.
• Stoppage of electric current
• ON timer is set.
REMOTE CONTROL A-B SELECTION
18
To separate using of remote control for each indoor unit in case of 2 air conditioner
are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold button on the Remote Control by the tip of the pencil. "00" will be
shown on the display.
4. Press during pushing . "B" will show on the display and "00" will disappear
and the air conditioner will turn OFF. The Remote Control B is memorized.
Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not "A" display.
3. Default setting of Remote Control from factory is A.
Room Temperature
21°C ~ 32°C
17°C ~ 32°C
Cooling is abnormally low.
• The fi lters are blocked with dust.
• The temperature has been set
improperly.
• The windows or doors are opened.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is FAN or DRY.
1/24/07 2:32:12 PM 1/24/07 2:32:12 PM
EN