Related Manuals for Philips AECS7000
Summary of Contents for Philips AECS7000
-
Page 1: User Manual
Always there to help you Register your product and get support at www.philips.com/welcome AECS7000 Question? Contact Philips User manual... -
Page 3: Table Of Contents
Contents 1 Important Important safety information Notice 2 Your WeCall speaker Introduction What's in the box Product overview 3 Get started Charge the WeCall speaker Turn on the WeCall speaker Connect the WeCall speaker 4 Use the WeCall speaker Use as a speaker phone Use together with the WeCall app (for iPhone or Android phone) Use as a Bluetooth or PC speaker... -
Page 4: Important
• Clean only with dry cloth. device that are not expressly approved by • Do not block any ventilation openings. Philips Consumer Lifestyle may void the user’s Install in accordance with the authority to operate the equipment. manufacturer’s instructions. •... - Page 5 ® normal household waste. Correct disposal of registered trademarks owned by Bluetooth your old product helps to prevent potential SIG, Inc. and any use of such marks by Philips is negative consequences for the environment and under license. human health.
-
Page 6: Your Wecall Speaker
2 Your WeCall speaker To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. Introduction This Bluetooth conference speaker (WeCall speaker) allows you to: • connect to a Bluetooth enabled smartphone and make a mobile or VoIP call through the WeCall speaker directly. -
Page 7: Product Overview
Product overview f USB/ source switch • Switch between the USB or Bluetooth • Adjust volume during a call or music audio sources. play. b ON/OFF power switch • Answer an incoming mobile call. • Power on or off the WeCall speaker. • End an ongoing mobile call. -
Page 8: Get Started
3 Get started Turn on the WeCall speaker Slide the power switch to the ON position. • » In Bluetooth mode, the status indicator Caution turns blue. • Use of controls or adjustments or performance of » In USB mode, the source indicator procedures other than herein may result in hazardous turns green. - Page 9 Slide the source switch at the bottom of Enable Bluetooth on your Bluetooth- the WeCall speaker to the USB position. enabled device. Select ‘Philips WeCall speaker‘ on your Bluetooth-enabled device and if necessary input ‘0000’ as the paring password. » The source indicator starts to flash blue.
-
Page 10: Use The Wecall Speaker
App (for iPhone) Make sure that you have selected the Bluetooth source on the WeCall speaker. Download Philips WeCall to your iPhone. Make a mobile or VoIP call on your mobile phone, or a VoIP call (such as a SkypeTM call) on your tablet or PC/Mac. - Page 11 Confirm the telephone number and code. Set events for conference calls in the calendar of your iPhone or Android phone. Run Philips WeCall and import conference calls from your calendar. Make a conference call.
-
Page 12: Use As A Bluetooth Or Pc Speaker
• • During a call, you can use on the WeCall During audio play, you can use on the WeCall speaker to adjust volume. speaker to adjust volume. • • During a call, you can press to mute the WeCall During audio play, you can press to mute the speaker so that the other party cannot hear you. -
Page 13: Product Information
5 Product information Amplifier Rated Output Power 2W RMS Frequency Response 80Hz -16k Hz, ±3dB Signal to Noise Ratio >75dB Bluetooth Bluetooth version V2.1 + EDR ® Frequency band 2.402-2.480 GHz ISM Band Range 10m (free space) Speakers Speaker Impedance 4ohm Speaker Driver 1"... -
Page 14: Troubleshooting
Hold CLEAR at the bottom of the requesting service. If the problem remains WeCall speaker for more than 3 seconds unsolved, go to the Philips Web page (www. to reset, and then try again. philips.com/support). When you contact Philips, •... - Page 16 Specifications are subject to change without notice © 2013 Koninklijke Philips Electronics N.V. All rights reserved. AECS7000_00_UM_V1.0...