Clarke SPP10 7175030 Operating & Maintenance Instructions
Clarke SPP10 7175030 Operating & Maintenance Instructions

Clarke SPP10 7175030 Operating & Maintenance Instructions

1hp swimming pool pump
Hide thumbs Also See for SPP10 7175030:

Advertisement

1HP SWIMMING POOL PUMP
Model SPP10
Part No: 7175030
OPERATING & MAINTENANCE
INSTRUCTIONS
GC12/11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPP10 7175030 and is the answer not in the manual?

Questions and answers

Summary of Contents for Clarke SPP10 7175030

  • Page 1 1HP SWIMMING POOL PUMP Model SPP10 Part No: 7175030 OPERATING & MAINTENANCE INSTRUCTIONS GC12/11...
  • Page 2 The pump inlet is higher than the impeller inlet so that it can start operating when only the pump body is filled with water. Upon receipt, any damage or deficiency should be reported to your CLARKE dealer immediately. CONTENTS...
  • Page 3: General Safety Precautions

    11. This pump must be connected to an earthed power supply via a RCD. 12. ALWAYS have the pump serviced by your local CLARKE dealer, using only identical replacement parts. This will ensure the safety of the pump is maintained.
  • Page 4: Electrical Connections

    ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz.
  • Page 5: Installation

    Because of the variety of possible installations, no plumbing accessories are supplied with your pump, however accessories are available from your nearest CLARKE dealer. Contact your CLARKE dealer for further information, or CLARKE International Sales Department on 01992 565333. Note: It is recommended that the end user should consult a qualified installer if there are any doubts as to the suitability of this product for a particular installation.
  • Page 6: Electrical Connection

    ELECTRICAL CONNECTION The pump should be located at a safe distance, (usually 2 metres), away from the pool, and the power supply should be at least 3.5 metres from the pool. If in doubt, please contact your electrical specialist and refer to the International Electrical Commission (IEC) standard, (Electrical Installations for Buildings-part 7), referring to ‘swimming pools and other basins’.
  • Page 7: Operation

    If a leak is noticed at this point, it may indicate that the seal is worn and therefore in need of replacement. Contact your CLARKE dealer, or the Clarke International Service Department for advice. 2. In the event of a blockage, where debris has entered the suction chamber, the sieve and chamber can be cleaned out as described under MAINTENANCE.
  • Page 8: Maintenance

    ° Couplings and 90 Hose Adaptors, etc. Contact your Clarke dealer for further information. The use of parts other than genuine Clarke replacement parts may result in possible safety hazards or decreased machine performance, and will invalidate your warranty. ENVIRONMENTAL PROTECTION Do not dispose of this product with general household waste.
  • Page 9: Troubleshooting

    TROUBLESHOOTING . y l s l i f - l l t t i l n i n i l l n i t i f y l l t l i t l i t l i & v i l n i l v i l n i l...
  • Page 10 TROUBLESHOOTING s i s l n i . s r t i s n i l . r i . r i SPP10 PERFORMANCE Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 11: Technical Specification

    Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 12: Parts List

    PARTS LIST n i l n i l f f i n i l t l i Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 13: Parts Diagram

    PARTS DIAGRAM Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 14: Declaration Of Conformity

    DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 15 DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...

Table of Contents