Related Manuals for Clarke SPPT1
Summary of Contents for Clarke SPPT1
- Page 1 SWIMMING POOL PUMP Model SPPT1 Part No: 7175040 OPERATING & MAINTENANCE INSTRUCTIONS GC05/12...
- Page 2 The pump inlet is higher than the impeller inlet so that it can start operating when only the pump body is filled with water. The SPPT1 incorporates an integral timer which can be set to operate for a pre-determined time between 2 and 24 hrs. The timer has a back up battery to save the settings in case of loss of electrical power, allowing the pump to start again once power is restored.
-
Page 3: General Safety Precautions
10. NEVER switch the pump ON when the pool is in use. ALWAYS disconnect the pump from the electrical supply when the pool is in use. 11. ALWAYS have the pump serviced by your local CLARKE dealer, using only identical replacement parts. This will ensure the safety of the pump is maintained. -
Page 4: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 5: Installation
Because of the variety of possible installations, no plumbing accessories are supplied with your pump, however accessories are available from your nearest CLARKE dealer. Contact your CLARKE dealer for further information, or CLARKE International Sales Department on 01992 565333. Note: It is recommended that the end user should consult a qualified installer if there are any doubts as to the suitability of this product for a particular installation. -
Page 6: Electrical Connection
ELECTRICAL CONNECTION The pump should be located at a safe distance, (usually 2 metres), away from the pool, and the power supply should be at least 3.5 metres from the pool. If in doubt, please contact your electrical specialist and refer to the International Electrical Commission (IEC) standard, (Electrical Installations for Buildings-part 7), referring to ‘swimming pools and other basins’. - Page 7 Do not allow the pump to run dry, otherwise the seal between the pump and motor may be damaged. If a leak is noticed at this point it may indicate that the seal is worn and therefore in need of replacement. Contact your CLARKE dealer, or the Clarke International Service Department for advice.
-
Page 8: Operation
OPERATION 1. Open any valves in the pipeline. 2. If operating the pump for the first time, disconnect the top hose and prime the pump by filling completely with water. Note: The pump is only self- priming when filled with water. Refilling is only necessary if the pump has been drained, or if all the water has been lost. -
Page 9: Care During Use
Always keep the pump in a clean condition, checking regularly for loose bolts or a damaged power cable etc. The pump should not be taken apart by the user in the case of overhaul being required, but should be taken to your nearest Clarke dealer for specialist repair. AFTER USE After use, and if the pump will not be used over the winter period, or whenever there is danger of freezing, always drain the pump body. -
Page 10: Environmental Protection
1.8 m Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 11: Troubleshooting
TROUBLESHOOTING e l l . y l s l i f - l l t t i l n i n i l i k s l n i t i f y l l & v i l n i l v i l n i l l n I... - Page 12 TROUBLESHOOTING s i s l n i . s r t i s n i l . r i . r i SPPT1 PERFORMANCE Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 90 hose adaptors, etc. Contact your Clarke dealer for further information. The use of parts other than genuine Clarke replacement parts may result in possible safety hazards or decreased pump performance and will invalidate your warranty.
-
Page 14: Spare Parts
SPARE PARTS When requesting spare/replacement parts for these pumps from CLARKE Parts & Service, please quote the prefix ‘ZG’ followed by the model number (SPPT1) and the item number from the parts list/diagram. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the SPPT1 and is the answer not in the manual?
Questions and answers