User Manual 8120-B1 ADSL2+ with 4 Ethernet Ports Switch Gateway Issue 1.0 July. 2008...
Page 2
(“Marks”) displayed on this manual are the property of Innoband or other third parties. Users are not permitted to use these Marks without the prior written consent of Innoband or such third party that may own the Mark. IBM is a registered trademark of International Business Machines Corporation. Intel and Pentium are registered trademarks of Intel Corporation.
8120-B1 User’s Guide Introduction....................1 Features ..........................1 Device Requirements ......................2 Getting to know the device................ 3 Parts Check...........................3 Front Panel..........................4 Rear Panel ..........................5 Connecting your device................6 Connecting the Hardware.....................6 Step 1. Connect the WAN port to ADSL network ................. 7 Step 2.
Features The list below contains the main features of the device 8120-B1 and may be useful to users with knowledge of networking protocols. The chapters throughout this guide will provide you with information to get the most out of your device.
8120-B1 User’s Guide Device Requirements In order to use the device, you must have the following: DSL High speed broadband Internet service Instructions from your ISP on what type of Internet access you will be using, and the IP addresses needed to set up access One or more computers, each containing an Ethernet card (10Base-T/100Base-T network interface card (NIC)).
8120-B1 User’s Guide Getting to know the device Parts Check In addition to this document, your package should arrive containing the following: The device (8120-B1) Ethernet cable (RJ-45) Standard phone line cable (RJ-11) Power adapter 8120-B1 device RJ-45 Cable Ethernet Cable...
8120-B1 User’s Guide Front Panel The front panel of the device 8120-B1 will be described here. Figure 2: Front Panel and LEDs LED definitions from left to right: Label Color Function Off : No power Green On : Power on...
8120-B1 User’s Guide Rear Panel The rear panel of the device 8120-B1 will be described here. Figure 3: Rear Panel Connections Connector definitions from left to right: Label Function DSL Jack: Connects to the ADSL network LAN1 ~ LAN4 Connects the device via Ethernet to your devices in LAN...
8120-B1 User’s Guide Connecting your device This chapter provides basic instructions for connecting the device to a computer or LAN and to the Internet. In addition to configuring the device, you need to configure the Internet properties of your computer(s). For more details, see the Configuring Ethernet PCs section in Appendix A.
8120-B1 User’s Guide Step 1. Connect the WAN port to ADSL network Using the phone cable (RJ-11), connect the WAN port to the ADSL network which has the high speed internet connection. Step 2. Connect the Ethernet cable Connect up to four single Ethernet computers or to a HUB/Switch directly to the device via Ethernet cable(s).
8120-B1 User’s Guide Getting Started with the Web pages The device includes a series of Web pages that provide an interface to the software installed on the device. It enables you to configure the device settings to meet the needs of your network. You can access it through a web browser on a PC connected to the device.
Page 14
8120-B1 User’s Guide Advanced Setup: provides information about the current configuration of various system features with options to change the configuration. It includes the sub menus: WAN, LAN, NAT, Security, Parental Control, Quality of Service, Routing, DNS, DSL, Interface Group, and IPsec.
8120-B1 User’s Guide Commonly used buttons The following buttons are used throughout the web pages: Button Function Click this button to refresh the information on this page to get the real time updated information. Click this button to create an entry into the list.
8120-B1 User’s Guide If the LEDs illuminate as expected, test your Internet connection from a LAN computer. To do this, open your web browser, and type the URL of any external website (such as http://www.yahoo.com). If the LEDs do not illuminate as expected, you may need to configure your Internet access settings using the information provided by your ISP.
8120-B1 User’s Guide Device Information The Device Information web page menu includes the following submenus: Summary Statistics Route DHCP (shown in router mode) Summary The Summary Page of the device shows the following information: Board ID, Software version, Bootloader (CFE) version, and LAN MAC address. Also, ADSL line upstream and downstream sync up rates, LAN IP address, Default Gateway, Primary DNS Server and Secondary DNS Server are shown as well.
8120-B1 User’s Guide Figure 7: WAN Port Information Statistics The Statistics Page of the device shows two interfaces: data transmissions in received direction and data transmissions in transmitted direction. Each interface shows information such as total bytes, packets, error count and drop count of LAN port, WAN port, ATM, and ADSL.
8120-B1 User’s Guide Route The Route Page of the device shows the route table. It contains Destination IP address, Gateway, Subnet Mask, Flag, Metric, Service, and Interface. Figure 12: Device Route Table Information The ARP Page of the device shows the ARP table mapping the IP address and related MAC address.
8120-B1 User’s Guide Advanced Setup The Advanced Setup menu includes the sub menus: WAN, LAN, NAT, Security, Parental Control, Quality of Service, Routing, DNS, DSL, Interface Group, and IPSec. Security Parental Control Quality of Service Routing Interface Group IPSec You can configure your internet connection from this page. This page displays the details of existing internet connection.
Page 22
8120-B1 User’s Guide To configure the WAN port, click Edit for existing internet connections or Add for creating new internet connections to get the configuration pages. If there are many services (protocols) in the single PVC interface, please enter the unique VLAN tag number to identify the service (protocol).
Page 23
8120-B1 User’s Guide Click Next to configure the Connection Type. Figure 18: WAN Connection Type Configuration Global Settings: Check the WAN protocol from PPP over ATM (PPPoA), PPP over Ethernet (PPPoE), MAC Encapsulation Routing (MER), IP over ATM (IPoA), and Bridging.
8120-B1 User’s Guide PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) Figure 19: WAN Connection, PPPoA or PPPoE Configuration To configure the PPPoA or PPPoE settings: Enter the User’s PPP Username and Password. Enter the Service Provider Name if any.
Page 25
8120-B1 User’s Guide Figure 20: WAN Service, PPPoA or PPPoE Configuration NAT, Firewall, IGMP Multicast and WAN service settings: Check to enable NAT, which allows multiple PCs in the LAN environment to surf the Internet simultaneously with the same WAN IP address.
8120-B1 User’s Guide MAC Encapsulation Routing (MER) Figure 22: WAN Connection, MER Configuration To configure the MER settings: Select “Obtain an IP address automatically” or “Use the following (fixed) IP address”. If the second option is selected, enter the WAN IP address and WAN Subnet Mask.
8120-B1 User’s Guide WAN service settings: Check to enable NAT which allows multiple PCs surfing Internet simultaneously by using the same WAN IP address. Check to enable Firewall. Check to enable IGMP Multicast to avoid multicast packet flooding to other LAN ports where using IGMP packet to get better efficiency in the Ethernet port is not necessary.
8120-B1 User’s Guide Bridging Figure 25: WAN Connection, Bridging Configuration To configure the Bridging settings: Check “Enable Bridge Service” to enable bridge service. Enter the Service Name for this bridging interface. Click Next. The WAN Setup Summary page shows all of the parameters. Please refer to Figure 21: WAN Summary, PPPoA or PPPoE Configuration on page 20 for reference.
8120-B1 User’s Guide Figure 26: LAN Configuration To configure LAN: Enter the IP address which the CPE in the LAN will use to connect to the device. For example, enter 192.168.1.1 Enter the Subnet Mask. For example, enter 255.255.255.0 Check to enable UPnP feature. (shown in router mode) Check to Enable IGMP Snooping.
8120-B1 User’s Guide NAT (Network Access Translation) The NAT feature provides the basic firewall feature to avoid hacker attacks from a remote site. There are four more setting pages including: Virtual Server, Port Triggering, DMZ Host, and ALG to provide specified service for remote users.
8120-B1 User’s Guide Global Settings: Select a Service from the predefined list or enter the name of Custom Server. Enter the Server IP Address located in the LAN to provide the service to remote party. Enter the Start External Port # and End External Port # that open to let remote parties access the service.
8120-B1 User’s Guide Figure 30: Add a Rule of Port Triggering Global Settings: Select an application from the predefined list or enter the name of Custom Application. Enter the Start Trigger Port # and End Trigger Port # that open to let remote parties access the service.
8120-B1 User’s Guide Figure 31: Add a Rule of DMZ Host Global Settings: Enter the DMZ Host IP address. Click Save/Apply. An ALG (Application Layer Gateway) is a method to allow specific applications to pass through the NAT firewall. Figure 32: ALG Configuration Global Settings: Check to select SIP ALG enabled.
8120-B1 User’s Guide Security IP Filtering The device can block the packet in outgoing and incoming directions. By default, all outgoing IP packets from LAN is allowed to surf the Internet, but some IP packets can be blocked by setting up filters.
Page 35
8120-B1 User’s Guide Global Settings: Enter the Filter Name. Select the Protocol from the selection list. Enter the Source IP Address and Subnet Mask (range of IP addresses) of packet. Enter the Source Port: one port or multi ports (port range).
Page 36
8120-B1 User’s Guide Figure 36: Add - Incoming IP Filter Setup Global Settings: Enter the Filter Name. Select the Protocol from the selection list. Enter the Source IP Address and Subnet Mask (range of IP addresses) of packet. Enter the Source Port: one port or multi ports (port range).
8120-B1 User’s Guide Parental Control This feature allows you to configure some of the PCs in LAN to surf the Internet in specific time period and also setup the URL filter list. Figure 37: Parental Control Configuration Global Settings: Click Add to add a rule of schedule for parental control.
8120-B1 User’s Guide URL Filter The device can screen and filter the URL packet. Figure 39: URL Filter Setup Global Settings: Select to either exclude or include the URL in the list. Click Add to add an URL entry. Check Remove and click Remove to remove the specified entry.
8120-B1 User’s Guide Quality of Service The Quality of Service feature provides a method to prioritize the packet and arrange a better efficiency of bandwidth. In other words, some traffic such as voice or video handles a higher priority than others such as data to get near real time response.
8120-B1 User’s Guide Queue Configuration You can configure a maximum of 16 QoS queues to provide different service levels. Figure 42: Quality of Service Queue Configuration Global Settings: Click Add to add a class of Qualify of Service. Check Remove and click Remove to remove the specified entry.
8120-B1 User’s Guide QoS Classification You need to define one or more classes of data traffic and set the priority for each of classes. Figure 44: Quality of Service Classification Setup Global Settings: Click Add to add a class of Qualify of Service.
Page 42
8120-B1 User’s Guide The screen creates a traffic class rule to classify the upstream traffic and to assign the queue priority which defines the precedence and type of service. A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect.
8120-B1 User’s Guide Routing This section shows the IP addresses or address routes for the computers connected to the gateway to reach different destinations, such as the local network, the gateway, or the Internet. The Routing feature provides three more setting pages including Default Gateway, Static Route, and RIP.
8120-B1 User’s Guide Click Add to add the static route path. Check Remove and click Remove to remove the specified entry. Figure 48: Add Static Route Configuration Global Settings: Enter the Destination Network Address and Subnet Mask (range). Check Use Gateway IP Address and enter the IP address where packet will be forwarded to.
8120-B1 User’s Guide The DNS feature provides two more setting pages including DNS server setting and Dynamic DNS. DNS Server Figure 50: DNS Configuration Global Settings: Check Enable Automatic Assigned DNS checkbox. This router will accept the first received DNS assignment from one of the PPPoE or Static IP/DHCP interface. If the checkbox is not checked, enter the IP addresses of the static Primary DNS Server and Secondary DNS Server.
8120-B1 User’s Guide Global Settings: Click Add to add Dynamic DNS setting. Check Remove and click Remove to remove the specified entry. Figure 52: Add a Dynamic DNS Global Settings: Select the Dynamic DNS service provider from the list. Enter the Hostname.
8120-B1 User’s Guide Global Settings: Check to select the DSL modulation modes. Select the DSL phone line pair: inner pair or outer pair. The default setting is inner pair. Check to select the Capabilities, Bitswap and/or SRA (Seamless Rate Adaption).
Page 48
8120-B1 User’s Guide Figure 55: Add a Port Mapping Group Configuration Global Settings: Enter the Group Name. Select the available LAN ports from available LAN interfaces into grouped interface. The selected LAN interface will be removed from its original group and joined this new group.
8120-B1 User’s Guide IPSec This page provides VPN IPSec configuration. You can establish a VPN tunnel (IPSec) with remote site to secure the data traffic between two sites. Figure 56: VPN IPSec Tunnel Configuration Current settings will be shown. Click “Add New Connection” to add an entry.
Page 50
8120-B1 User’s Guide Select Subnet if there is a group of remote IP addresses access VPN tunnel or Single Address if one remote IP address only. Enter the remote IP address for VPN and its Subnet mask. Select the Key Exchange Method from AUTO (IKE) or Manual.
8120-B1 User’s Guide Diagnostics The Diagnostic web page provides the connection check in physical layer and upper layer. The result is helpful to figure out the problems if you have troubles surfing the Internet. Diagnostics This page will show up the result of diagnostics in physical layer like WAN port and also upper layer of IP protocol.
8120-B1 User’s Guide Management The Management web page menu comprises of: Settings System Log TR-069 Client Internet Time (shown in router mode) Access Control Update Software Save/Reboot Settings This page allows you to backup the current configuration of the device, update the configuration, and restore to the default configuration (factory setting).
8120-B1 User’s Guide Restore Default Figure 62: Restore Default Settings Click Restore Default Settings to restore the factory default settings. System Log This page allows you to view system log and also configure system log that way you want to see it.
8120-B1 User’s Guide Global Settings: Select to Enable or Disable log function. Select Log Level from the list. Select Display Level from the list. Select Mode from the list. Click Save/Apply to save the configuration. TR-069 Client This page allows you to access TR-069 ACS (Auto-Configuration Server). The ACS can provision, configure, and diagnostic the device from remote site.
8120-B1 User’s Guide Internet Time This page allows you to sync up to the real time clock from Internet. Figure 66: Internet Time Configuration Global Settings: Check to enable Automatically synchronize with Internet time servers. Click Save/Apply to save your settings.
8120-B1 User’s Guide Global Settings: Select the method by which you wish to access the router locally or remotely. The following are the methods available for local and remote access: HTTP ICMP (Ping) TELNET TFTP Click Save/Apply to save the configuration.
8120-B1 User’s Guide Password There are three levels of access accounts: admin, support, and user. The user name “admin” has unrestricted access to change and view configuration of the device. The user name “support” is used to allow an ISP technician to access the device for maintenance and to run diagnostics.
8120-B1 User’s Guide Update Software This page allows you to update the software (firmware). Figure 71: Management Configuration – Update Software Global Settings: Get the updated software (firmware) from your ISP or manufacturer. Click Browse… to specify the location and file name.
8120-B1 User’s Guide Appendix A - Configuring the Internet Settings This appendix provides instructions for configuring the Internet settings on your computers to work with the device. Configuring Ethernet PCs Before you begin By default, the device automatically assigns the required Internet settings to your PCs.
8120-B1 User’s Guide Click OK twice to confirm your changes, and then close the Control Panel. Windows 2000 PCs In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. Double-click the Network and Dial-up Connections icon.
8120-B1 User’s Guide Appendix B - Troubleshooting This appendix suggests solutions for problems you may encounter in installing or using the device, and provides instructions for using several IP utilities to diagnose problems. Contact Customer Support if these suggestions do not resolve the problem.
8120-B1 User’s Guide Problem Troubleshooting Suggestion If you have not changed the password from the I forgot/lost my user ID or default, try using “admin” as both the user ID password. and password. Otherwise, to reset the device to the default configuration, press and hold the RES button on the rear panel of the device for 7 seconds.
8120-B1 User’s Guide address, such as that for www.yahoo.com (216.115.108.243). If you do not know the IP address of a particular Internet location, you can use the nslookup command, as explained in the following section. For most other IP-enabled operating systems, you can execute the same command at a command prompt or through a system administration utility.
8120-B1 User’s Guide Appendix C - Glossary Term Description 802.11 A family of specifications for wireless LANs developed by a working group of the IEEE. This wireless Ethernet protocol is often called Wi-Fi. 10BASE-T A designation for the type of wiring used by Ethernet networks with a data rate of 10 Mbps.
Page 65
8120-B1 User’s Guide types of data. See routing. Broadband A telecommunications technology that can send different types of data over the same medium. DSL is a broadband technology. Broadcast To send data to all computers on a network. DHCP Dynamic Host Configuration Protocol DHCP automates address assignment and management.
Page 66
8120-B1 User’s Guide File Transfer Protocol A program used to transfer files between computers connected to the Internet. Common usages include uploading new or updated files to a web server, and downloading files from a web server. Gbps Abbreviation of Gigabits per second, or one billion bits per second.
Page 67
8120-B1 User’s Guide Light Emitting Diode An electronic light-emitting device. The indicator lights on the front of the device are LEDs. MAC address Media Access Control address The permanent hardware address of a device, assigned by its manufacturer. MAC addresses are expressed as six pairs of hex characters, with each pair separated by colons.
Page 68
8120-B1 User’s Guide PPPoA Point-to-Point Protocol over ATM One of the two types of PPP interfaces you can define for a Virtual Circuit (VC), the other type being PPPoE. You can define only one PPPoA interface per VC. PPPoE Point-to-Point Protocol over Ethernet One of the two types of PPP interfaces you can define for a Virtual Circuit (VC), the other type being PPPoA.
Page 69
8120-B1 User’s Guide TFTP Trivial File Transfer Protocol A protocol for file transfers, TFTP is easier to use than File Transfer Protocol (FTP) but not as capable or secure. TKIP Temporal Key Integrity Protocol (TKIP) provides WPA with a data encryption function. It ensures that a unique...
Page 70
8120-B1 User’s Guide Wide Area Network Any network spread over a large geographical area, such as a country or continent. With respect to the device, WAN refers to the Internet. Web browser A software program that uses Hyper-Text Transfer Protocol (HTTP) to download information from (and...
8120-B1 User’s Guide Registration Card Innoband 8120-B1 Product Registration Name: Company: Address: City/State/Zip: Phone: E-mail: Serial Number: Purchased from: Date of Purchase: Please cut out the above Product Registration Card and send in with a self-addressed stamped envelope to: Innoband Technologies, Inc.
But if it does, the user will be required to correct the interference at user’s own expense. The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the equipment unless Innoband expressly approves the changes or modifications.
Page 76
8120-B1 User’s Guide FCC Part 68 Notice This equipment complies with Part 68 of FCC Rules. On the base unit of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. IF REQUESTED, THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.
Page 77
8120-B1 User’s Guide UL Safety Regulations Disconnect TNV circuit connector before removing cover or equivalent. Disconnect TNV circuit connector(s) before disconnecting power. Do not use this product near water for example, near a bathtub, washbowl, and kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
Appendix G - Contact information We would more than love to help if you have further technical questions, please visit our Website at http://www.innoband.com or send E-mail to support@innoband.com. To purchase accessories or replacement parts for this router, please visit http://www.innocow.com. Company Address...
Need help?
Do you have a question about the 8120-B1 and is the answer not in the manual?
Questions and answers