Zanussi ZGG 642 Instruction Booklet
Zanussi ZGG 642 Instruction Booklet

Zanussi ZGG 642 Instruction Booklet

Hide thumbs Also See for ZGG 642:

Advertisement

Quick Links

GAS HOB
ZGG 642
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB

Advertisement

Table of Contents
loading

Summary of Contents for Zanussi ZGG 642

  • Page 1 GAS HOB ZGG 642 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance...
  • Page 2: Important Safety Information

    Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727 727. Installation • This appliance must be installed and serviced by a Unstable or misshapen pans should not be used on competent person as stated in the Gas Safety the hob as unstable pans can cause an accident by (Installation and Use) Regulations Current Editions...
  • Page 3: Table Of Contents

    Contents For the Installer For the User Engineers technical data Important Safety Information Important safety requirements Description of the Hob Installation Operation Building In Maintenance and Cleaning Electrical connections Something Not Working? Wiring Diagram Guarantee/Customer Service Fault Finding European guarantee Commissioning Conversion from Natural Gas to LPG Environmental Information...
  • Page 4: Description Of The Hob

    Description of the Hob 1. Semi-rapid Burners 2. Rapid Burner 3. Auxiliary Burner 4. Control knobs...
  • Page 5: Operation

    Operation Hob burners To light a burner: Avoid cooking with potstones, earthenware push in the relevant control and turn it to maximum pots or cast iron plates. Also, avoid using aluminiun foil for protecting the top during position; operation. then adjust the flame as required. If the burner does not ignite, turn the control knob to To ensure maximum burner efficiency, you should only zero, and try again.
  • Page 6: Something Not Working

    Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
  • Page 7: Engineers Technical Data

    Instructions for the Installer Engineers technical data Rapid Burner OVERALL DIMENSIONS Heat Input 2.9 kW Natural Gas (9895 BTU/HR) 2.7 kW L.P.G. (9212 BTU/HR) Width: 580 mm. Depth: 510 mm. Semi-rapid Burner Heat Input 1.9 kW (6483 BTU/HR) CUT OUT DIMENSIONS Auxiliary Burner Width: 550 mm.
  • Page 8: Important Safety Requirements

    Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current The hob may be located in a kitchen, a kitchen/diner or Edition) and the IEE Wiring Regulations (Current bed sitting room, but not in a bathroom, shower room Edition).
  • Page 9: Installation

    Installation IMPORTANT This hob must be installed by a competent and qualified person only. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e.
  • Page 10: Building In

    Building In Building over a kitchen unit with Building over a cupboard or door drawer Proper arrangements must be taken in designing the If the hob is to be installed above a cupboard or drawer furniture unit, in order to avoid any contact with the it will be necessary to fit a heat resistant board below bottom of the hob which can be heated when it is the base of the hob on the underside of the work surface.
  • Page 11: Electrical Connections

    Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations.
  • Page 12: Wiring Diagram

    Wiring Diagram 220/240 A. IGNITOR SWITCH Brown B. IGNITOR UNIT Fault Finding SOCKET Preliminary Electrical Systems PLUG (with cover (face view) removed) Check Earth Wire Green/Yellow Blue Green START Yellow Isolate appliance and carry out: A: Earth Continuity Neutral Wire Blue check.
  • Page 13 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and replace if Light burner manually necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point Check position of the Check earth continuity electrode of appliance...
  • Page 14: Commissioning

    Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
  • Page 15: Guarantee/Customer Service

    Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ·...
  • Page 16: European Guarantee

    European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: •...
  • Page 20 35690-0402 11/06...

Table of Contents