Table of Contents
Advertisement
Advanced Features
Semi-OSD Settings
The semi-OSD system places one line messages
at the lower third of the video display screen
whenever the Volume, Input Source, Surround
mode or tuner frequency of any of the configura-
tion settings are changed. The semi-OSD system
is helpful in that enables you to have feedback
on any control changes or remote commands
using the video display when it is difficult to view
the front-panel displays. However, you may
occasionally prefer to turn these displays off for a
particular listening session. You may also want to
adjust the length of time the displays remain on
the screen. Both of those options are possible
with the AVR.
To turn off the semi-OSD system, you will need to
make an adjustment in the
ADVANCED
menu (Figure 23). To start the adjust-
SELECT
ment, press the OSD button
to bring the
to the screen. Press the
MASTER MENU
, until the on-screen ➞ cursor is next
Button
to the
line. Press the Set Button
ADVANCED
to enter the
ADVANCED SELECT
menu.
At the
ADVANCED SELECT
certain that the on-screen ➞ cursor is next to the
line by pressing the
SEMI OSD
as needed. Next, press the
›
button
that the word
is highlighted in the video
OFF
display.
Note that this setting is temporary and will
remain active only until it is changed or until the
AVR is turned off. Once the unit is turned off, the
semi-OSD displays will remain activated, even if
they were switched off for the previous listening
session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
Menu as outlined
ADVANCED SELECT
earlier, and press the
buttons
/
⁄
¤
needed, until the on-screen ➞ cursor is next to
the
line. Next,
SEMI-OSD TIME OUT
press the
‹
›
Buttons
until the desired time
/
in seconds is displayed. Note that unlike most of
the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
If you wish to make other adjustments in the
menu, press the
Buttons
/
⁄
¤
screen ➞ cursor is next to the desired setting or
the
BACK T O MASTER MENU
press the Set button
. If you have no other
adjustments to make, press the OSD Button
to exit the menu system.
48 ADVANCED FEATURES
Full-OSD Time Out Adjustment
The
FULL OSD
simplify the setup and adjustment of the AVR
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of
inactivity before they disappear from the screen
or Time Out. This Time Out is a safety measure to
prevent the menu text from burning into the
CRTs in your monitor or projector, which might
happen if they were left on indefinitely. However,
some viewers may prefer a slightly longer or
shorter period before the Time Out display.
To change the Full-OSD Time Out, you will need
to make an adjustment in the
menu (Figure 23). To start the adjust-
SELECT
ment, press the OSD button
MASTER MENU
, until the on-screen ➞ cursor is next
button
to the
ADVANCED
⁄
to enter the
menu (Figure 23).
At the
ADVANCED SELECT
certain that the on-screen ➞ cursor is next to the
menu make
FULL OSD TIME OUT
Buttons
/
⁄
¤
buttons
‹
›
buttons
/
/
⁄
¤
so
played in seconds. Note that unlike most of the
other options in this menu, this is a permanent
setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments in the
menu, press the
on-screen ➞ cursor is next to the desired setting
or the
BACK T O MASTER MENU
press the Set button
adjustments to make, press the OSD Button
to exit the menu system.
Bridge
as
DMP/
The
TM
When using Harman Kardon's optional
iPod docking station, the normal operation is to
have the iPod selected as the input source only
when it is specifically chosen. However, you may
set the AVR so that whenever the iPod is turned
on, the AVR will also turn on automatically and
set The Bridge as the input.
To change the setting, first make certain that the
ADVANCED SELECT
until the on-
on the screen, and then press the
Navigation Buttons
line and
pointing to
DMP AUTO POWER
Navigation Buttons
/
⁄
¤
is highlighted to have the AVR turn on in sync
with an iPod, or
menu system is used to
ADVANCED
to bring the
to the screen. Press the
⁄
line. Press the Set Button
ADVANCED SELECT
menu make
line by pressing the
as needed. Next, press the
until the desired time is dis-
Buttons
until the
/
⁄
¤
line and
. If you have no other
Auto Power
The
Bridge
TM
menu (Figure 23) is
/
⁄
¤
F until the cursor is
. Press the
F so that
O N
for standard operation.
OFF
Hide quick links:
Advertisement
Table of Contents
