40 Tuner Operation; Basic Tuner Operation; Station Selection; Preset Tuning - Harman Kardon AVR 630 Owner's Manual

Multiroom Operation / Tuner Operation
when the Surround Back amplifier channels
are configured for Multiroom use, as shown on
page 36. This adjustment does NOT change the
volume level for any room where an ABUS mod-
ule is used, as that setting is only adjustable
using the A-BUS module's volume control or
built-in IR sensor.
Once the multiroom system is turned on, it will
remain on even if the AVR is placed in the
Standby mode in the main room by pressing the
Power Off Button or the System Power
Control on the front panel. To turn off the
multiroom system from the main listening room,
when the AVR is on press the Multiroom but-
ton and then the Set button
Press the buttons so that the Main
/
Information Display or OSD will display
.
Even when the AVR is turned off (to Standby
mode) and the multiroom system is turned off
too, the multiroom system may be turned on at
any time by pressing the Multiroom button
, or any of the Selector buttons
in the remote room.

40 TUNER OPERATION

Basic Tuner Operation

The AVR's tuner is capable of tuning AM, FM and
FM Stereo broadcast stations and receiving RDS
data. Stations may be tuned manually, or they
may be stored as favorite station presets and
recalled from a 30 position memory.

Station Selection

1. Press the AM/FM Tuner Select button
on the remote to select the tuner as an input.
The tuner may be selected from the front panel
by either pressing the Input Source Selector
until the tuner is active or by pressing the
Tuner Band Selector
.
2. Press the AM/FM Tuner Select button
or Tuner Band Selector
between AM and FM so that the desired
frequency band is selected.
3. Press the Tuner Mode button
remote or hold the Band Selector
front panel pressed for 3 seconds to select
manual or automatic tuning.
When the button is pressed so that
appears in the Main Information Display
each press of the Tuning Selectors
put the tuner in a scan mode that seeks the next
higher or lower frequency station with accept-
able signal strength. An
indication will momentarily appear when the sta-
tion stops at a stereo FM station, and an
indication will momentarily appear
when an AM or monaural FM station is tuned.
Press the Tuning buttons again to scan to the
next receivable station.
When the button is pressed so that
appears in the Main Information Display
each tap of the Selector will increased or
decrease the frequency by one increment. When
the tuner receives a strong enough signal for
adequate reception,
appear in the Main Information Display
4. Stations may also be tuned directly by press-
ing the Direct button
the Numeric Keys
station's frequency. Note that for entering num-
bers higher than 100 you need to enter only the
"1" rather than "10", the first "0" will be
added automatically. The desired station will
automatically be tuned after the latest number is
entered. If you press an incorrect button while
entering a direct frequency, press the Clear
button
NOTE: When the FM reception of a stereo
station is weak, audio quality will be increased
by switching to Mono mode by pressing the
at any time.
Tuner Mode button
ing the Band Selector
again to switch
that
Main Information Display
out.
on the

Preset Tuning

on the
Using the remote, up to 30 stations may be
stored in the AVR's memory for easy recall using
the front panel controls or the remote.
To enter a station into the memory, first tune the
station using the steps outlined above. Then:
will
1. Press the Memory button
remote. Note that two underscore lines will
appear in the Main Information Display
2. Within five seconds, press the Numeric
Keys
you wish to store this station's frequency. Once
entered, the preset number will appear in the
Main Information Display
3. Repeat the process after tuning any additional
stations to be preset.
Recalling Preset Stations
• To manually select a station previously entered
in the preset memory, press the Numeric Keys
that correspond to the desired station's
will
memory location.
.
• To manually tune through the list of stored
preset stations one by one, press the Preset
Stations Selector buttons
front panel or remote.
, and then pressing
that correspond to the
to start over.
on the remote or hold-
on the front panel so
appears momentarily in the
and then goes
on the
corresponding to the location where
.
on the
.