Programming The Remote; Programming The Remote With Codes - Harman Kardon AVR 5000 Owner's Manual

Programming the Remote

The AVR5000 is equipped with a powerful
remote control that will control not only the
receiver's functions, but also most popular brands
of audio and video equipment, including CD
players, TV sets, cable boxes, VCRs, satellite
receivers and other home-theater equipment.
Once the AVR5000's remote is programmed with
the codes for the products you own, it is possible
to eliminate most other remotes and replace
them with the convenience of a single universal
remote control.
Programming the Remote
with Codes
As shipped from the factory, the remote is fully
programmed for all AVR5000 functions, as well as
those of most Harman Kardon CD changers, DVD
players, CD players and cassette decks. In addition,
by following one of the methods below, you may
program the remote to operate a wide range of
devices from other manufacturers.
Note: The Input Selector button Video 4
cannot be programmed with codes as it functions
as input selector for the AVR only. Moreover, only
the default code "001" can be programmed on
the AVR Selector button .
Direct Code Entry
This method is the easiest way to program your
remote to work with different products.
1. Use the tables in the following pages to deter-
mine the three-digit code or codes that match
both the product type (e.g., VCR, TV), and the
specific brand name. If there is more than one
number for a brand, make note of the different
choices.
2. Turn on the unit you wish to program into the
AVR5000 remote.
3. Press and hold both the Input Selector
for the type of product to be entered (e.g., VCR,
TV) and the Mute button
time. When the Program/SPL Indicator
turns amber and begins flashing, release the but-
tons. It is important that you begin the next step
within 20 seconds.
4. If the unit you wish to program into the
AVR5000 remote has a remotable Power on/off
function, follow these steps:
a. Point the AVR5000's remote towards the unit to
be programmed, and enter the first three-digit
code number using the Numeric buttons
If the unit being programmed turns off, the cor-
rect code has been entered. Press the Input
Selector again, and note that the red
light under the Input Selector will flash three
times before going dark to confirm the entry.
b. If the product to be programmed does NOT
turn off, continue to enter the three-digit code
numbers until the equipment turns off. At this
point, the correct code has been entered. Press
the Input Selector
the red light under the Input Selector will
flash three times before going dark to confirm
the entry.
5. If the Power function of the unit to be pro-
grammed cannot be remoted, follow these steps
(max. 20 seconds after step 3 above, or else step
3 must be repeated first):
a. Enter the first three-digit code number using
the Numeric buttons
Input Selector
button of any transport function remotable
with the unit, e.g. Pause or Play
the unit being programmed starts that func-
tion, the correct code has been entered.
b. If the unit does not start the function whose
button was pressed, repeat steps 3 and 5a
above with the next three-digit code number
listed in the setup code table for that brand
and product type, until the unit reacts properly
on the transport function transmitted.
6. Try all of the functions on the remote to make
certain that the product operates properly. Keep
in mind that many manufacturers use a number
of different combinations of codes, so it is a good
idea to make certain that not only does the
Power control work, but that the volume, channel
and transport controls work as they should. If
functions do not work properly, you may need to
use a different remote code.
7. If the unit does not react to any code en-
tered, if the code for your product does not
appear in the tables in this manual, or if not all
functions operate properly, try programming the
remote with the Auto Search Method.
at the same
Note on Using the AVR5000 remote with a
Harman Kardon CD Recorder.
As shipped from the factory the remote is pro-
grammed for controlling Harman Kardon CD
players. But it is able to control most functions
of the CD Recorder CDR2 and CDR20 (see func-
tion list on page 44) too after the code "002" is
entered to the CD Selector button
described above. For returning to the CD player
control commands the code "001" must be
entered.
.
Auto-Search Method
If the unit you wish to include in the AVR5000's
remote is not listed in the code tables in this
manual or if the code does not seem to operate
properly, you may wish to program the correct
code using the Auto Search method that follows.
Note that the Auto Search method works only
with units whose Power functions can be
remoted:
1. Turn on the product that you wish to include in
the AVR5000 remote.
again and note that
2. Press and hold both the Input Selector
for the type of product to be entered (e.g., VCR,
TV) and the Mute
time. When the Program/SPL Indicator
turns amber and begins flashing, release the but-
tons. It is important that you begin the next step
within 20 seconds.
3. To find out if the code for your unit is pre-pro-
grammed, point the AVR5000 remote towards the
and press the
unit to be programmed, and press and hold the
again. Press the remote
button
from the remote's built-in data base, with each
. If
flash of the red light under the Input Selector
the device to be programmed turns off,immediate-
ly release the
one minute or more until the right code is found
and the unit turns off.
4. When the
after the unit turned off, the proper code will be
"overrun". That's why a function test should be
made: Turn the unit on again and, while the
Input Selector
button
too. When the unit turns off, the right code was
found, when not, the code was "overrun". To re-
find the correct, while the Input Selector
still lights red, press (not hold pressed) the
button
through the codes available and observe the
reaction of the unit at each press. As soon as the
unit turns off the correct code is found.
5. Press the Input Selector
note that the red light will flash three times
before going dark to confirm the entry.
6. Try all of the functions on the remote to make
certain that the product operates. Keep in mind
that many manufacturers use a number of differ-
ent combinations of codes, and it is a good idea
to make certain that not only the Power control
works, but the volume, channel and transport
controls, as appropriate. If all functions do not
as work properly, you may need to Auto-Search for
a different code, or enter a code via the Direct
Code Entry method.
button at the same
. This will send out a series of codes
indicating that a code has been sent. When
button . Note that it may take
button was not released in time
still lights red, press the
once, than the button
repeatedly to step backwards
again, and
PROGRAMMING THE REMOTE
once
39