Learning Codes; Erasing Learned Codes; Macro Programming - Harman Kardon AVR 510 Owner's Manual

Programming the Remote

Learning Codes

In addition to using codes from the remote's
internal code library, the AVR 510's remote is
able to "learn"codes from remotes that may
not be in the code library. In addition, you may
use this function to "learn over" the codes from
a preprogrammed device to add functions not
included in the preprogrammed codes. To learn
or transfer codes from an IR remote to the
AVR 510's remote, follow these steps:
1. Place the front of the original remote with
the code being sent so that it is facing the
IR Transmitter Window on the
AVR 510 remote "head-to-head. " The
remotes should be between one and three
inches apart.
2. Select the button on the remote that you
wish to use as the device selector for the
codes about to be entered. This may be any
of the Input Selectors .
3. Press the Input Selector button
chosen and the Learn button
same time. Hold these buttons until the
Program/SPL Indicator flashes amber
and the light under the device selector but-
ton turns red. Release the buttons.
4. Press the button on the AVR 510 remote that
you wish to program. Note that the
Program/SPL Indicator will stop
flashing.
5. Within five seconds, press and hold the but-
ton on the original remote that you wish to
"teach" into the AVR 510 remote. When the
Program/SPL Indicator turns green
three times, release the button. Note that the
Program Indicator will then begin to flash
amber again.
NOTE: If the Program/SPL Indicator
turns red during Step 5 or 6, the program-
ming was not successful. Repeat the steps to
see if the code will "take. "
6. Repeat Steps 4 though 6 for each button on
the source remote that you wish to transfer
to the AVR 510 remote.
7. Once all codes have been transferred from
the original source remote to the AVR 510
remote, press the Learn button
8. Repeat Steps 1 through 7 for any addi-
tional remotes you wish to "teach" into the
AVR 510 Remote.

Erasing Learned Codes

The AVR 510's remote allows you to remove or
erase, the code learned into a single button for a
single device, to remove or erase the code set for
all the codes that have been programmed into
specific device buttons, or to erase all commands
that have been learned to all devices.
To erase a single learned code from within a sin-
gle device's settings, follow these steps:
1. Press and hold both the Input Selector
within which the individual but-
ton to be erased has been programmed and
the Learn button
2. When the red LED under the Input Selector
turns red and the Program/SPL Indicator
flashes amber, release the buttons.
3. Press and release the Input Selector
again for the device within
at the
which the individual button to be erased has
been programmed.
4. Press the 7 button
5. Press and release the individual button for
which the code is to be erased. The
Program/SPL Indicator
two times and then return to amber.
6. To erase other buttons within the same device,
press them as noted in Step 5.
7. When all buttons to be erased have been
pressed, press the Learn button
complete the process.
To erase all codes within a single device, follow
these steps:
1. Press and hold both the Input Selector
for which you wish to erase the
codes and the Learn button
2. When the red LED under the Input Selector
turns red and the Program/SPL Indicator
flashes amber, release the buttons.
3. Press and release the Input Selector
again for the device whose
.
codes you wish to erase.
4. Press the 8 button
5. The Program/SPL Indicator
off and the red light under the Input
Selector will flash on and off once to indi-
cate that the codes have been erased.
To erase all codes that have been programmed
to all devices in the remote, follow these steps:
1. Press any Input Selector
which you wish to erase the codes and also
the Learn button
2. When the red LED under the Input Selector
turns red and the Program/SPL Indicator
3. Press and release the Input Selector
.
codes you wish to erase.
4. Press the 9 button
5. The Program/SPL Indicator
off and the red light under the Input
Selector will flash on and off once to
indicate that the codes have been erased.

Macro Programming

Macros enable you to easily repeat frequently
four times.
used combinations of commands with the press
of a single button on the AVR 510's remote con-
trol. Once programmed, a macro will send out
up to 19 different remote codes in a predeter-
will blink green
mined sequential order enabling you to auto-
mate the process of turning on your system,
changing devices, or other common tasks. The
AVR 510's remote can store up to five separate
macro command sequences: one that is
associated with the Power On button
four more that are accessed by pressing the
to
Macro buttons
1. Press the Mute button
Macro button
the Power On button
time. Note that an Input Selector will light
red, and the Program/SPL Indicator
will flash amber.
.
2. Enter the steps for the macro sequence by
pressing the button for the actual command
step. Although the macro may contain up to
19 steps, each button press, including those
used to change devices, counts as a step.
The Program/SPL Indicator
green to confirm each button press as you
enter commands.
four times.
37 PROGRAMMING THE REMOTE
will turn
for
.
flashes amber, release the buttons.
again for the device whose
four times.
will turn
.
38 and the
to be programmed or
at the same
will flash
and