Making And Receiving Calls; Battery Duration; When To Purchase A New Battery Pack; Choose The Dialing Mode - Sony SPP-N1001 Operating Instructions Manual

Prepare the battery pack
Insert the battery into the handset and charge first before you start using your phone.
1
Slide open the battery compartment lid of the handset.
2
Connect the battery connector with correct polarity (black wire goes on
lower side and red wire goes on upper side).
3
Insert the battery pack, and close the lid.
4
Place the handset on the base unit.
The LINE/CHARGE lamp lights up when the handset is properly seated
on the charge terminals of the base unit. Charge the battery pack for
more than 12 hours so that the battery is fully charged. The LINE/
CHARGE lamp remains lit even after charging is completed.
1
2
BP-T50
Black

Battery duration

A fully charged battery pack lasts for about:
• 10 hours when you use the handset continuously.
• 30 days when the handset is in standing by.
Notes
• The battery pack will gradually discharge over a long period of time, even if not in use.
• If you leave the battery pack in the handset without charging it, the battery pack will be
completely discharged. It may require several times of charging to recover to its full capacity.
• If the battery runs out completely, the setting of dialing mode, the speed dial numbers and the
digital security code will be erased. If this happens, charge it on the base unit for over 12 hours.
Then choose the dialing mode, set the ringer type, reprogram the speed dial numbers, and
assign a new digital security code (see "Resetting the digital security code"). You may need to
charge the battery several times before it is recharged to its full capacity.
To obtain the best performance from battery
Do not place the handset on the base unit after each call. The battery works best if the
handset is returned to the base unit after two or three calls. However, do not leave the
handset off the base unit for a long period of time as this will completely discharge
the battery pack.

When to purchase a new battery pack

If the battery lasts only a few minutes even after 12 hours of charging, the usable
life of the battery has expired and needs replacement. Contact your local Sony
authorized dealer or service center, and ask for Sony BP-T50 rechargeable battery
pack.
Note
Battery life may vary depending on usage condition and ambient temperature.

Choose the dialing mode

For the telephone to work properly, select an appropriate dialing mode (tone or
pulse). The default setting is tone.
TALK/BATT
LOW lamp
1, 4
2
Note
Do not allow more than 20 seconds to elapse between each step of the procedure.
3
4
Red
LINE/CHARGE
lamp
1
Press (PGM).
The TALK/BATT LOW lamp
flashes.
The dialing keys light up.
2
Press (* TONE).
You hear a confirmation beep.
3
Press (1) for pulse dialing or
(2) for tone dialing.
4
Press (PGM).
You hear a long confirmation
beep and the TALK/BATT LOW
lamp goes off.

Making and receiving calls

Making calls
(FLASH)
TALK/BATT
VOL
LOW lamp
switch
2
4
(* TONE)
(REDIAL/PAUSE)
Microphone
(CHANNEL/RINGER)
Receiving calls
1
When you hear the phone ring;
• Press (TALK) (or any key except (OFF)).
or
• Pick up the handset from the base unit when the handset is placed on
the base unit.
The TALK/BATT LOW lamp lights up.
2
When you're done talking, replace the handset on the base unit or press
(OFF).
The TALK/BATT LOW lamp goes off.
Additional tasks
To Do this
Adjust the handset Set the VOL switch to H (high), M (middle) or L (low).
volume
Press (* TONE) after you're connected.
Switch to tone
dialing temporarily
The line will remain in tone dialing until disconnected.
While the handset is not in use, press (CHANNEL/RINGER). Each
Set the ringer type
press of (CHANNEL/RINGER) switches the ringer type by one of
four type.
Press (FLASH).
Switch to another
call ("call waiting
Press the button again to get back to the first caller.
service"*)
* You need to subscribe to the service from your telephone company.
Notes
• Do not cover the microphone during the conversation; otherwise, the other party cannot hear
your voice.
• If you hear beeps during the conversation, move closer to the base unit; otherwise, the call will
be disconnected after 15 seconds. Note that, however, you may not hear beeps if it's noisy on
the handset.
If interference occurs on the handset
When you press (TALK), the handset automatically searches for the channel with the
best reception. However, if you notice interference during a conversation, move
closer to the base unit.
If interference persists, press (CHANNEL/RINGER) to switch to another channel to
improve the sound quality of your telephone conversation.
Note
If you hear five short beeps when you press (CHANNEL/RINGER), move closer to the base unit.
If the handset battery becomes weak during a call
The handset will beep every three seconds with the TALK/BATT LOW lamp
flashing at the same time. Finish your call and charge the battery pack.
Caution
If this occurs, you cannot use the handset without charging it for more than one minutes.
Redialing
Press (TALK), and wait until the TALK/BATT LOW lamp lights up.
1
Press (REDIAL/PAUSE) to redial the number last dialed.
2
Note
If the number exceeds 32 digits, the beeps will alert you that the number cannot be dialed.
To erase the last phone number dialed
Press (REDIAL/PAUSE) twice.
The number will be erased from the memory, and you'll hear a long confirmation
beep.
1
Pick up the handset from the
base unit.
2
Press (TALK), and wait until
the TALK/BATT LOW lamp
lights up.
The dialing keys light up.
You then hear a dial tone. If
you hear beeps, move closer to
the base unit.
3
Dial the phone number.
4
When you're done talking,
press (OFF).
The TALK/BATT LOW lamp
goes off.