Setting The Clock (Remote Control Only); Listening To The Ipod - Sharp XL-DH320NH Operation Manual

Setting the clock (Remote control
only)
CD
USB
In this example, the clock is set for the 24-hour (0:00)
display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button.
Press the or button to select 24-hour or 12-
hour display and then press the MEMORY button.
The 24-hour display will appear.
"0:00"
(0:00 - 23:59)
The 12-hour display will appear.
"AM 12:00"
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
"AM 0:00"
(AM 0:00 - PM 11:59)
4
To adjust the hour, press the
then press the MEMORY button. Press the
button once to advance the time by 1 hour. Hold it
down to advance continuously.
5
To adjust the minutes, press the
then press the MEMORY button. Press the
button once to advance the time by 1 minute.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
The "CLOCK" will appear or time will be displayed when
the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as
follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK"
does not appear in step 2, step 3 (for selecting the 24-hour
or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Clear all the programmed contents. [Refer to "Factory
reset, clearing all memory" on page 21 for details.]
2
Perform "Setting the clock" from step 1 onwards.

Listening to the iPod

Supported iPod models:
● iPod nano (software 1.2 above)
● iPod mini (software 1.2 above)
● iPod (5
● iPod (4
● iPod nano (2
● iPod nano (3
● iPod nano (4
● iPod classic (software 1.0.3 above)
● iPod touch (software 1.1 above)
● iPod touch (2
Caution:
Please update your iPod unit to the latest software version
from Apple's homepage before using it.
Notes:
● Once the iPod is connected to the unit it will begin
● The iPod unit cannot be charged whilst the main unit is
Auto power on function:
When you press any of the following buttons, the unit turns
on.
● iPod button on the remote control: The unit turns on
●
■ iPod adaptor connection
Choose the iPod adaptor that fits your iPod. Your iPod will
or button and
fit snuggly into the correct adaptor. If your iPod is not
or
mentioned below, an iPod adaptor may have been
included with your iPod unit.
or button and
or
Adaptor No.
Notes:
● iPod nano 2G, iPod nano 3G, iPod classic and iPod
● If you have an iPod that does not have an iPod 30 Pin
● iPhone is not supported by this system.
E-6
th
generation) (software 1.3 above) (Dock
connector equipped Click Wheel model)
th
generation) (software 3.0.2 above) (Dock
connector equipped Click Wheel model)
nd
generation) (software 1.0.0 above)
rd
generation) (software 1.0.3 above)
th
generation) (software 1.0.3 above)
nd
generation) (software 2.1 above)
charging.
in the stand-by mode or during USB mode.
and the iPod function is activated.
/ button on the main unit: The unit turns on and
playback of the last function will start (iPod, CD,
TUNER, USB, AUDIO IN).
The marking shows
which iPod fits
iPod iPod Description
9 5G iPod (with video)
9 U2 iPod with video
9 iPod classic
10 5G iPod with video
10 iPod classic
A iPod mini
A 4G iPod & U2 iPod
A iPod photo & colour U2
iPod
A iPod with colour display
B 4G iPod
B iPod photo
B iPod with colour display
touch are not compatible with the iPod adaptors listed
above. Please use the adaptor supplied with your iPod
unit.
connector, you can use an audio cable to connect it to
the AUDIO IN socket.
9
Capacity
30GB
30GB
80GB, 120GB
60GB & 80GB
160GB
4GB & 6GB
20GB
20GB & 30GB
20GB
40GB
40GB & 60GB
60GB