Contents COPYRIGHT INFORMATION yCopyright yDisclaimer yAbout this manual IMPORTANT SAFETY INSTRUCTIONS yDisposal of old electrical and electronic equipment yImportant Recycle Instructions: INTRODUCTION yAbout This Manual yDescription, Features and Benefits yParts List CONTROLS AND FUNCTIONS yD8800/D8900/D8010W at a Glance yI/O Panel yKEYPAD yRemote control yTo install batteries in the remote control...
Page 3
Start using the projector - Operation ySelecting An Input Source ySelecting an Aspect Ratio yUsing the OSD Start using the projector - OSD Introduction yOSD Menu Tree yOSD Introduction - INPUT yOSD Introduction - PICTURE yOSD Introduction - LAMPS yOSD Introduction - ALIGNMENT yOSD Introduction - CONTROL yOSD Introduction - SERVICE Change Lamp...
DLP Projector - User’s Manual IMPORTANT SAFETY INSTRUCTIONS Thank you for your purchase of this quality product! For best performance, please read this manual carefully as it is your guide through the menus and operation. Read and Keep these instructions. 2.
DLP Projector - User’s Manual Disposal of old electrical and electronic equipment (Applicable throughout the European Union and other European countries with separate collection programs) This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it.
Equipped with precision optics, the D8800/D8900/D8010W include zoom, focus and lens shift controls for a throw range of 1.85:1 to 2.40:1. For a smaller throw distance (1.56:1 to 1.86:1), the D8800/D8900/ D8010W can be fitted with a varying optics package (optional) to meet different requirements. Exceptional scaling and film-to-video (3:2 pull-down) conversion is easily achieved.
Additional Features of the D8800/D8900/D8010W yHorizontal and vertical lens shift. yKeystone adjustment. Parts List Your D8800/D8900/D8010W is shipped with the following items, if any items are missing or damaged, please contact your dealer or Vivitek Customer Service. Accessory Box List D8800/D8900/D8010W...
DLP Projector - User’s Manual CONTROLS AND FUNCTIONS D8800/D8900/D8010W at a Glance yAir outlet Warm air exits the projector through this vent. Ensure that it is not blocked. yAir inlet Internal fans draw cool air into the projector through this vent.
Provides a standard, 15-pin VGA-style connection to either an RGB or component high-definition source, or to a personal computer. The D8800/D8900/D8010W automatically detect the input signal resolution. yRS-232 9-pin D-sub connector for interfacing with a PC or home theater automation/control system.
DLP Projector - User’s Manual KEYPAD POWER INPUT AUTO SYNC ASPECT OPEN CLOSE SHUTTER LENS FOCUS ZOOM SHIFT MENU EXIT yPOWER Use the button to turn on/off the projector. yINPUT Press to select a video source. HDMI, DVI, VGA, Component / BNC Composite, S-Video or 3D-SGI. Press this to re-acquire the current active source.
DLP Projector - User’s Manual Remote control Use this button to turn the projector on. Use this button to turn the projector off. POWER FOCUS Focuses the projected images. ZOOM Zoom in/out the projected image. TEST PATTERN FOCUS ZOOM Use this to enter test pattern menu. TEST PATTERN LENS SHIFT...
DLP Projector - User’s Manual To install batteries in the remote control STEP 1 STEP 2 STEP 3 Slide the battery compartment cover in the direction of the arrow to remove it. 2. Install two AA batteries with the correct polarity. 3.
Throw Distance (TD) = Screen Width (W) x Throw Ratio (TR) Two models of the D8800/D8900/D8010W are available, one with 1.56-1.86:1 lens and the other with 1.85-2.40:1 lens With optional zoom adaptors throw ratios of 1.24 – 3.0 can be achieved. The standard D8800/D8900/D8010W offer throw ratios between 1.85:1 and 2.40:1.
DLP Projector - User’s Manual Modes of installation Frontal projection - desktop installation Advantages: easy to install can be easily moved or adjusted easy to operate. Disadvantage: occupies floor space and limits seating capacity. Rear projection - desktop installation Advantage: the projector is completely hidden from plain view the projector can be easily operated this setup usually offers better reduction of ambi-...
DLP Projector - User’s Manual Allow at least 50 cm clearance around the exhaust vent. The device need to have enough space to prevent issues as stated in this image. 50cm 50cm Or Greater Or Greater Side Way 70cm Or Greater Back Side 30cm Or Greater...
Lens Shift Vertical Lens Shift The D8800/D8900/D8010W have a lens shift capability which allows the vertical movement of the image without mov- ing the projector. Lens shift is generally expressed as a percentage of the screen height. For ceiling mounted projectors, the lens can be moved 50% (0.5V) downward, while the lens can be moved 50% (0.5V) up or down on a desktop mounted...
Connecting the projector to other devices. Proceed as follows to connect the D8800/D8900/D8010W to your video sources, external controller(s) - if present - and AC power. When connecting your equipment: •Use the correct signal cables for each source. •Ensure that the cables are securely connected.
If infrared signals from the remote control cannot reach the projector due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR repeater system to the IR INPUT on the D8800/D8900/D8010W to extend the range of the remote control.
RS-232 DTV set-top-box or other compo- nent (YPbPr) input source RS-232 Connection Connect a PC or home theater control/automation system (if present) to the RS-232 port on the D8800/D8900/D8010W. Use a standard, 9-pin serial cable, wired straight-through. HDMI DVI-D Desk Top or Notebook...
Connecting to AC Power The D8800/D8900/D8010W ship with various types of AC power cords. Choose the one that is appropriate to your locale. Plug the female end of the power cord into the AC receptacle on the rear of the projector (AC 100V ~ 240V); Then, connect the other end to your AC power source.
< > Language Enter Adjusting the Picture Orientation If the D8800/D8900/D8010W is installed behind the screen, you must change the picture orientation to match the installation method. Refer to “Modes of installation” on page 15. To do this, press MENU on the remote control.
DLP Projector - User’s Manual Lens Adjustments The D8800/D8900/D8010W gives you a great deal of control over the picture size, position and focus. Focus To focus the projected image, grasp the lens by the front ring and rotate it. Adjust foot Rotate the 4 feet on projector for image position.
DLP Projector - User’s Manual Start using the projector - Operation Selecting An Input Source When you turn on the D8800/D8900/D8010W, it switches to the last selected input and looks for a INPUT INPUT valid signal. Press on the remote control to select an input source directly.
DLP Projector - User’s Manual Start using the projector - OSD Introduction OSD Menu Tree HDMI High Bright Display Mode Presentation Video Input Selection Component / BNC Contrast 0~200 Brightness Composite S-Video Adaptive Contrast 3G-SDI Saturation PIP Option 0~200 PIP Input Film PIP Swap Gamma...
Page 27
DLP Projector - User’s Manual Front Standard Eco Network Power Rear Projection Mode Ceiling + Front Auto Power Off Ceiling + Rear Auto Power On Normal RS232 Projector Control Fan Mode Network Down IP Address Zoom Subnet mask Lens Control Network Focus Gateway...
DLP Projector - User’s Manual OSD Introduction - INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE INPUT Input Selection Enter Enter Test Pattern Enter Color Space < RGB-PC > Input Lock < Auto > Background < Logo > Video Standard < ----- >...
Page 29
YCbCr 4:2:2 128m Note: Signals are not supplied for D8800/D8900/D8010W, if it is not in the table. yPIP You can use this function to display multiple windows each containing an image. PIP Option Use this to turn the function On/Off.
Page 30
RGB-Video color space. For component SDTV and EDTV resolutions, REC601 is used. For other component video resolutions, REC709 is used. RGB: If Hsync or Vsync signals are present, the D8800/D8900/D8010W use the RGB-PC color space. Other- wise, REC601 is used for SDTV and EDTV sources, and REC709 for all other sources. Component: For SDTV and EDTV resolutions, the D8800/D8900/D8010W use the REC601 color space.
Page 32
DLP Projector - User’s Manual yColor to adjust the color temperature of the projected image. ySharpness The adjustment of sharpness primarily changes the value of high frequency detail. Use to adjust it. yNoise Reduction to adjust the noise of the projected image. This function is suitable for the elimination of image noise ...
Page 33
DLP Projector - User’s Manual yOverscan Some consumers may use the image that input source is not 16:9, and some programs may not display the edges of the image. Use this function to hide the image edge by choosing one of the following three options: Crop Zoom 16:9...
DLP Projector - User’s Manual OSD Introduction - LAMPS INPUT PICTURE ALIGNMENT CONTROL SERVICE LAMPS Mode < Single > Power < > High Altitude < > Custom Power Level < ----- > Lamp 1 Status : Lamp 2 Status : yMode function to select single or dual lamp mode.
DLP Projector - User’s Manual OSD Introduction - ALIGNMENT INPUT PICTURE LAMPS CONTROL SERVICE ALIGNMENT Projection Mode < Front > Fan Mode < Normal > Lens Control Enter Lens Memory Enter Center Lens Execute Warp Enter Blanking Enter Edge Blend Enter yProjection Mode function to select the projection mode (Front, Rear,...
Page 36
DLP Projector - User’s Manual Pincushion / Barrel Press to correct pincushion/barrel distortion. Press to correct pincushion dis- tortion to correct image. Press to correct barrel distortion to correct image. Top Left Corner Press to correct top left corner image distortion.
Page 37
DLP Projector - User’s Manual yBlanking Use this function to adjust the edges of the image and hide unwanted sections of the screen. yTOP Press on the remote control to adjust the top blank- ing area on the projected image. yBottom Press on the remote control to adjust the bottom...
Page 38
DLP Projector - User’s Manual White Level Bottom Left Right Black Level Uplift Black Level Uplift is used to compensate for the lack of pure black output from projectors, due to light leak- ing to the projection screen. When projecting black , the hot area where the two images overlap project twice the projectors’...
DLP Projector - User’s Manual OSD Introduction - CONTROL INPUT PICTURE LAMPS ALIGNMENT SERVICE CONTROL Eco Network Power < > Auto Power Off < > Auto Power On < > Projector Control < ----- > Network Enter Start Up Logo <...
Page 40
DLP Projector - User’s Manual To connect to a network (LAN), refer to the following steps: Connect an RJ45 cable to LAN ports on the projector and a router or hub on the network. Projector (Ethernet) 2. On the control PC, open a web browser and enter the IP address of the projector. The Projector Web Server home page displays.
Page 41
DLP Projector - User’s Manual 3. Make any desired changes to projector settings, then Click Save. To connect to a stand alone PC or notebook, refer to the following steps: Connect an RJ45 cable to LAN ports on the projector and the PC (Laptop). HDMI DVI-D Desk Top or Notebook...
Page 42
DLP Projector - User’s Manual 3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP). 5. Click Properties. 6. Click Use the following IP address. Fill in the IP address and subnet mask. Make sure the IP address of the projector and PC are in the same network group.
Page 43
DLP Projector - User’s Manual 8. On the control PC, open a web browser and enter the IP address of the projector. The Projector Web Server home page displays. In the example, the projector resides at IP address 192.168.0.100. 9. Make any desired changes to projector settings, then Click Save. 10.
Page 44
DLP Projector - User’s Manual yStart Up Logo function to turn On/Off the start up logo. yTrigger The projector comes with one set of Trigger output. You can configure one devices connected to the projector via the trigger port to be automatically turned on when the projector is on. There will be a 2-3 second delay prior to activation to prevent operation of this function when the user is choosing the desired aspect ratio.
DLP Projector - User’s Manual OSD Introduction - SERVICE INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE Model : DP9675QDPxA Serial Number : C202XXXX00767 Software Version : MD05-GD02-Ub01- 9999-31-DPNE02-D02 Active/PIP Source : HDMI / Off Pixel Clock : 83 .30 MHZ Signal Format : 1280x800@60Hz H/V Refresh Rate : H: 49.578 KHZ V: 60 HZ...
Page 46
DLP Projector - User’s Manual yLamp 2 Time Display the lamp 2 usage time. When you change the new lamp. The lamp hours will re-calculate the time. yPower On Time Display the total On time for projector. Display only. yBlue Only Enabling this option will make the projector display only blue color to facilitate the process of image inspection for the service personnel.
DLP Projector - User’s Manual Change Lamp The lifecycle of ordinary projection lamp typically lasts for 1200 hours before requiring replacement (different lamp con- figurations will affect lamp life). From the OSD Menu, you can go to “OSD Introduction - SERVICE” on page 45 to check how long a lamp has been used.
DLP Projector - User’s Manual To replace the projector lamp2 Loosen the fan. 2. Use a screw driver to loosen the screws as shown in the illustration and pull the lamp out. 3. Insert the new lamp in the direction shown in the il- lustration into the lamp assembly;...
5. Secure the lens in the lens holder by turning coun- terclockwise the lens to the “locked” position. 6. Check if the lens is really secured by trying to pull the lens out of the lens holder. Six models of lens for D8800(WUXGA) ■ Vivitek Part Number Lens...
Page 50
DLP Projector - User’s Manual Six models of lens for D8900(XGA) Vivitek Part Number Lens Zoom Ratio D88-ST001 Standard Lens 1.7 ~ 1.9 1.79 ~ 2.35 D88-WF18501 Wide Fix 1.85 D88-WZ01 Wide Zoom 1.85 ~ 2.50 1.3 ~ 1.85 1.41...
DLP Projector - User’s Manual Change Filter The filter should be changed every 3000 hours. To replace the Filter on the left side of the projector Remove the cover on the left side of the projector. 2. Remove the filter from it. 3.
DLP Projector - User’s Manual To replace the Filter on the right side of the projector Loosen the fan cover on the right side of the projec- tor. 2. Open the fan cover and remove the filter from it. 3. Insert a new filter and install the fan cover on the right side of the projector.
DLP Projector - User’s Manual Change the Color Wheel The color wheel is on the top side. j Loosen the top cover Slide the cover and remove it. k Loosen the color wheel’s screw. Ç m Replace the color wheel that you wanted.
LED Display Projector status Procedure No Problem Flashing Red (Cycles of 1) Cover Problem Contact local Vivitek Server Center Red (Cycles of 4) Fan Problem Contact local Vivitek Server Center System Error Contact local Vivitek Server Center Lamp1/Lamp2 LED LED Display...
DLP Projector - User’s Manual SPECIFICATIONS Model D8800 D8900 D8010W Display Type Brightness 8000 ANS Lumens 10,000 ANS Lumens 8000 ANS Lumens Native Resolution WUXGA (1920 x 1200) XGA (1024 x 768) WXGA (1280 x 800) Maximum Resolution WUXGA (1920 x 1200)@60Hz...
DLP Projector - User’s Manual SERIAL INTERFACE SPECIFICATIONS Transfer Specifications Item Specifications Transmission Speed 38400 bps Data Length 8 bit Parity None Stop Bit Flow Control None RS-232 Commands There are 2 types of commands: yKey commands yOperation commands All commands start with 2 letters as shown in the following: y“ky”...
DLP Projector - User’s Manual Code RS232 Key name Key Wording Description 0x9E LIGHT CLEAR 0x9A Not available. 0x9B SHUTTER Turn on or off the shutter. 0x9C ID SET Not available. Operations Commands The following example is the syntax for operations commands: op <operation>...
DLP Projector - User’s Manual Projection Distance and Screen Size Optional Lenses (D88-LOZ101) Long Zoom 1 Lens Features and Specifications • F • gth: 52.8-79.1mm •Lens Shift Position: 0-50% Vertical; +/-10% Horizontal •Screen Size: 50”-300” •Focus adjustable Rang ” ” Z •...
Page 67
DLP Projector - User’s Manual Optional Lenses (D88-SMLZ01) Semi Long Zoom Lens Features and Specifications • F • •Lens Shift Position: 0-50% Vertical; +/-10% Horizontal •Screen Size: 50”-300” F • ” ” Z • • ” ” T • •F-Number: 1.86 - 2.48 Projection Distance V.S.
Page 68
DLP Projector - User’s Manual Optional Lenses (D88-WF18501) Wide Fix Lens Features and Specifications • F • gth: 11.6mm L • t f i S • ” ” •Focus adjustable Rang ” ” Z • •Optical Performance Rang ” ” T •...