Related Manuals for Vivitek D859
Summary of Contents for Vivitek D859
- Page 1 User Manual Manual del usuario Manuel de l'utilisateur Benutzerhandbuch Gebruikershandleiding Manuale d'uso Handbok Käyttöohje D8 Series...
- Page 2 Copyright This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2011 Disclaimer The information in this document is subject to change without notice.
- Page 3 DLP Projector—User’s Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
- Page 4 Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. Allow at least 50 cm clearance around the exhaust vent.
- Page 5 DLP Projector—User’s Manual Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly.
- Page 6 Preface Main Features • Lightweight unit, easy to pack away and transport. • Compatible with all major video standards including NTSC, PAL, and SECAM. • A high brightness rating allows for presentations in daylight or in lit rooms. • Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images. •...
-
Page 7: Table Of Contents
DLP Projector—User’s Manual Table of Contents GETTING STARTED ................................1 ................................1 ACKING HECKLIST ............................... 2 IEWS OF ROJECTOR ARTS Front-right View ................................2 Top view—On-screen Display (OSD) buttons and LEDs ....................3 Rear view ..................................4 Bottom view..................................5 .............................. - Page 8 Preface LED E ..............................47 RROR ESSAGES ................................47 MAGE ROBLEMS ................................48 ROBLEMS ............................48 EMOTE ONTROL ROBLEMS ................................48 UDIO ROBLEMS ..........................48 AVING THE ROJECTOR ERVICED HDMI Q & A................................. 49 SPECIFICATIONS................................50 ................................. 50 PECIFICATIONS ........................52 ROJECTION ISTANCE VS ROJECTION...
-
Page 9: Getting Started
DLP Projector – User’s Manual ETTING TARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP P ROJECTOR WITH EMOTE CONTROL CABLE OWER CORD AAA BATTERIES) WITH TWO CD-ROM ARRYING CASE UICK TART UIDE ARRANTY ’... -
Page 10: Views Of Projector Parts
DLP Projector—User’s Manual Views of Projector Parts Front-right View ABEL ESCRIPTION EE PAGE IR receiver Receive IR signal from remote control Height-adjuster button Push to release height adjuster Height adjuster Adjusts level of projector Lens Projection Lens Focus ring Focuses the projected image Zoom ring (*) Enlarges the projected image See Top view—On-screen Display (OSD) buttons... -
Page 11: Top View-On-Screen Display (Osd) Buttons And Leds
DLP Projector – User’s Manual Top view—On-screen Display (OSD) buttons and LEDs TEMP POWER LAMP ABEL ESCRIPTION PAGE Turns the projector On or Off (POWER) SOURCE Detects the input device AUTO Optimizes image size, position, and resolution ▲ (Up cursor) / Navigates and changes settings in the OSD KEYSTONE Quick Menu –... -
Page 12: Rear View
DLP Projector—User’s Manual Rear view 3 4 5 6 7 8 12 13 14 15 16 17 ABEL ESCRIPTION EE PAGE AC IN Connect the POWER CABLE (USB) Connect the USB CABLE from a computer 12V TRIGGER (*) Connect the DC 12V OUT Connect a LAN CABLE from Ethernet VIDEO IN Connect the COMPOSITE CABLE from a video device... -
Page 13: Bottom View
DLP Projector – User’s Manual Bottom view ABEL ESCRIPTION EE PAGE Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling Tilt adjustor Rotate adjuster lever to adjust angle position. Height adjustor Adjuster drops down when adjuster button is pushed. Height adjustor button Push to release adjustor. -
Page 14: Remote Control Parts
DLP Projector—User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. - Page 15 DLP Projector – User’s Manual ABEL ESCRIPTION EE PAGE IR transmitter Transmits signals to projector Status LED Lights when the remote control is used Laser Press to operate the on-screen pointer Up arrow when connected through USB to a PC Right Right arrow when connected through USB to a PC Down...
-
Page 16: Remote Control Operating Range
DLP Projector—User’s Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. -
Page 17: Setup And Operation
DLP Projector – User’s Manual ETUP AND PERATION Inserting the Remote Control Batteries Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the battery with the positive side facing up. Replace the cover. Caution: 1. -
Page 18: Connecting Input Devices
DLP Projector—User’s Manual Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector. -
Page 19: Starting And Shutting Down The Projector
DLP Projector – User’s Manual Starting and Shutting down the Projector Connect the power cord to the projector. Connect the other end to a wall outlet. POWER LED on the projector light. Turn on the connected devices. Ensure the LAMP LED not a flashing POWER orange. - Page 20 DLP Projector—User’s Manual When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has cooled down.
-
Page 21: Setting An Access Password (Security Lock)
DLP Projector – User’s Manual Setting an Access Password (Security Lock) You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 18 and Setting the OSD Language on page 19 for help on using OSD menus.) Important: Keep the password in a safe place. - Page 22 DLP Projector—User’s Manual You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password.
-
Page 23: Adjusting The Projector Level
DLP Projector – User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. •... -
Page 24: Adjusting The Zoom, Focus And Keystone
DLP Projector—User’s Manual Adjusting the Zoom, Focus and Keystone Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size .(*) Use the Image-focus control (on the projector only) to sharpen the pro- jected image Use the KEYSTONE buttons (on the projector or the remote control) to... -
Page 25: Adjusting The Volume
DLP Projector – User’s Manual Adjusting the Volume Press the Volume +/- buttons on the remote control. The volume control appears on the display. Volume Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-. TEMP POWER LAMP Press the MUTE button to... -
Page 26: On-Screen Display (Osd) Menu Settings
DLP Projector—User’s Manual (OSD) M CREEN ISPLAY ETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. -
Page 27: Setting The Osd Language
DLP Projector – User’s Manual Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cursor ▲▼ button until Language is highlighted. 3. -
Page 28: Osd Menu Overview
DLP Projector—User’s Manual OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. – 20 –... -
Page 29: Osd Sub-Menu Overview
DLP Projector – User’s Manual OSD Sub-Menu Overview Note: ot available in some models . (*) N – 21 –... -
Page 30: Image Menu
DLP Projector—User’s Manual Image Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change values for settings. -
Page 31: Advanced Feature
DLP Projector – User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the Advanced menu. -
Page 32: Color Manager
DLP Projector—User’s Manual Color Manager Press (Enter) / ► to enter the Color Manager sub menu. ESCRIPTION Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Select to enter the Green Color Manager. Green Press the ◄►... -
Page 33: Computer Menu
DLP Projector – User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Com- puter menu. Press the cursor ▲▼ button to move up and down in the computer menu. Press ◄► to change values for settings. -
Page 34: Video/Audio Menu
DLP Projector—User’s Manual Video/Audio Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu. Press ◄► to change values for settings. ESCRIPTION Video AGC Press the ◄►... -
Page 35: Audio
DLP Projector – User’s Manual Audio Press (Enter) / ► to enter the Audio sub menu. ESCRIPTION Press the ◄► buttons to adjust the audio volume. Volume (Range: 0~8) Mute Press the ◄► buttons to turn on or off the speaker. Press the cursor ◄►... -
Page 36: Installationi Menu
DLP Projector—User’s Manual Installation I Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press ◄►... -
Page 37: Advanced Feature
DLP Projector – User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation I menu. Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced menu. -
Page 38: Presentation Timer
DLP Projector—User’s Manual Presentation Timer The Presentation Timer function can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Press (Enter) / ► to enter the Presentation Timer sub menu. ESCRIPTION Timer Press the cursor ◄►... -
Page 39: Installation Ii Menu
DLP Projector – User’s Manual Installation II Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu. ESCRIPTION Auto Source Press the cursor ◄►... -
Page 40: Advanced Feature
DLP Projector—User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced menu. -
Page 41: Osd Menu Setting
DLP Projector – User’s Manual OSD Menu Setting ESCRIPTION Menu Position Press ◄► button to select different OSD location. Translucent Menu Press ◄► button to select OSD background translucent level. Menu Display Press ◄► button to select OSD timeout delay. Peripheral Test ESCRIPTION Remote Control Test... -
Page 42: Lamp Hour Reset
DLP Projector—User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 43 to reset the lamp hour counter. ESCRIPTION Press ◄► to select Off, DLP-Link or IR. 3D Sync Invert Press ◄► to turn 3D Sync Invert On or Off. –... -
Page 43: Network
DLP Projector – User’s Manual Network ESCRIPTION Network State Displays the network connection status. Press ◄► to turn DHCP On or Off. DHCP Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields. IP Address Enter a valid IP address if DHCP is turned off. - Page 44 DLP Projector—User’s Manual For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, Brightness and Contrast settings. Also, projector status information, such as: Video-Source, Sound-Mute, etc .
- Page 45 DLP Projector – User’s Manual 3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP). 5. Click Properties. 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. –...
- Page 46 DLP Projector—User’s Manual 7. Press the Menu button on the projector. Select Installation II → Advanced → Network. After getting into Network, input the following: DHCP: Off IP Address: 10.10.10.10 Subnet Mask: 255.255.255.0 Gateway: 0.0.0.0 DNS Server: 0.0.0.0 10. Press (Enter) / ►...
- Page 47 DLP Projector – User’s Manual ATEGORY NPUT ENGTH IP Address Crestron Control IP ID Port Projector Name Projector Location Assigned To DHCP (Enabled) (N/A) IP Address Network Configuration Subnet Mask Default Gateway DNS Server Enabled (N/A) User Password New Password Confirm Enabled (N/A)
-
Page 48: Factory Reset
DLP Projector—User’s Manual Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory Reset sub menu and press (Enter) / ► to reset all the menu items to the factory default values (expect Language and Security Lock). -
Page 49: Maintenance And Security
DLP Projector – User’s Manual AINTENANCE AND ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. - Page 50 DLP Projector—User’s Manual Remove the three screws from the lamp module. Lift the module handle up. Pull firmly on the module handle to remove the lamp module. 6. G Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is...
-
Page 51: Resetting The Lamp
DLP Projector – User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. -
Page 52: Cleaning The Projector
DLP Projector—User’s Manual Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. -
Page 53: Using The Kensington ® Lock
DLP Projector – User’s Manual ® Using the Kensington Lock ® Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. -
Page 54: Troubleshooting
DLP Projector—User’s Manual ROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose con- nection. -
Page 55: Led Error Messages
DLP Projector – User’s Manual LED Error Messages OWER RROR ESSAGES LINK LINK Standby mode Over temperature Thermal break status error Lamp error Fan1 error Fan2 error Fan3 error Lamp door open DMD error Color wheel error In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. -
Page 56: Lamp Problems
DLP Projector—User’s Manual Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green. 4. -
Page 57: Hdmi Tmq & A
DLP Projector – User’s Manual HDMI Q & A Q. What is the difference between a “Standard” HDMITM cable and a “High-Speed” HDMITM cable? Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High-Speed cables. ․Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal. -
Page 58: Specifications
DLP Projector—User’s Manual PECIFICATIONS Specifications D851 D853W D855ST Model D850 D85AA~AE D85CWA~CWE D85ESTA~ESTH Display type TI DMD 0.55” TI DMD 0.55” TI DMD 0.65” TI DMD 0.55” Resolution WXGA 1280x800 SVGA 800x600 1024x768 1024x768 Projection distance 1 ~ 10 m 1.5 ~ 10 m 0.5 ~5 m Projection screen size... - Page 59 DLP Projector – User’s Manual D857WT D859 Model D85GWTA~GWTE D85IA~IE TI DMD 0.65” TI DMD 0.55” Display type Resolution WXGA 1280x800 XGA 1024x768 Projection distance 0.5 ~ 5 m 1 ~ 10 m 43.8” ~ 438” 30” ~ 300” Projection screen size...
-
Page 60: Projection Distance Vs. Projection Size
DLP Projector—User’s Manual Projection Distance vs. Projection Size Projection Distance and Size Table D850 / D851 / D85AA～AE ROJECTION ROJECTION MAGE IAGONAL ISTANCE ISTANCE MAGE IDTH MAGE IGHT FFSET ( MM ) （ ） （MM） （MM） INCH INCH INCH 1300 1561 1951 2341... - Page 61 DLP Projector – User’s Manual D853W / D85CWA～CWE ROJECTION ROJECTION ISTANCE ISTANCE MAGE IAGONAL MAGE IDTH MAGE IGHT FFSET ( MM ) （ ） （MM） （MM） INCH INCH INCH 33.92 21.20 1310 1516 50.88 31.80 1964 2275 59.36 37.10 2292 2654 61.06 38.16...
- Page 62 81.41 50.88 1086 84.80 53.00 1131 101.76 63.60 1358 114.48 71.55 1527 127.20 79.50 1697 169.60 106.00 2263 D859 / D85IA～IE ROJECTION ROJECTION MAGE IAGONAL ISTANCE ISTANCE MAGE IDTH MAGE IGHT FFSET ( MM ) （ ） （MM） （MM） INCH...
-
Page 63: Timing Mode Table
DLP Projector – User’s Manual Timing Mode Table OMPOSITE IGNAL ESOLUTION OMPONENT / S-V HDMI IDEO NTSC 15.734 60.0 － － － － PAL/SECAM 15.625 50.0 － － － － VESA 720 x 400 37.9 85.0 － － 640 x 480 31.5 60.0 －... - Page 64 DLP Projector—User’s Manual OMPOSITE IGNAL ESOLUTION OMPONENT / S-V HDMI IDEO 1600 x 1200 75.0 60.0 － － 640 x 480 35.0 66.68 － － 832 x 624 49.725 74.55 － － Apple Mac 1024 x 768 60.24 75.0 － －...
-
Page 65: Projector Dimensions
DLP Projector – User’s Manual Projector Dimensions – 57 –... -
Page 66: Regulatory Compliance
DLP Projector—User’s Manual EGULATORY OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 67: Rs-232C Protocol
DLP Projector – User’s Manual PPENDIX RS-232C Protocol RS232 Setting Baud rate: 9600 Parity None check: Data bit: Stop bit: Flow Con- None trol Minimum delay for next command: 1ms Control Command Structure Header code Command code Data code End code Command Data ASCII... - Page 68 DLP Projector—User’s Manual 0:Cold VXXG0106 Get Color Temperature 1:Normal Pn/F 2:Warm 0:Cold VXXS0106n Set Color Temperature 1:Normal 2:Warm 0:PC 1:MAC VXXG0107 Get Gamma 2:Video Pn/F 3:Chart 4: B&W 0:PC 1:MAC VXXS0107n Set Gamma 2:Video 3:Chart 4: B&W Command Group 02 ASCII Function Description...
- Page 69 DLP Projector – User’s Manual VXXS0303n Auto Keystone On VXXG0304 Freeze On Pn/F VXXS0304n Freeze On VXXG0305 Volume n=0~8 Pn/F VXXS0305n Volume n=0~8 0:Front 1:Rear VXXG0308 Projection Mode Pn/F 2:Ceiling 3:Rear+Ceiling 0:Front 1:Rear VXXS0308n Projection Mode 2:Ceiling 3:Rear+Ceiling VXXG0309 Get vertical keystone value n= -30~30 Pn/F VXXS0309n...
- Page 70 2010 Vivitek Corporation. All rights reserved. All trademarks are the property of their respective owners. All specifications are subject to change without prior notice. 201009...